Products > Test Equipment

ngscopeclient - Ultimate acquisition software / protocol decoder / debug tool ?

<< < (6/11) > >>

Antonio90:

--- Quote from: fredo_ on September 14, 2024, 07:44:28 am ---Hi Antonio90 ,


--- Quote from: Antonio90 on September 13, 2024, 11:55:46 pm ---The console says something about the scope answering "welcome to SDS824X HD" after asking for an ID.

--- End quote ---
I think SDS800X HD support as not yet been merged to ngscopeclient (it is in scopehal git repo, but the ngscopeclient sub-module does not point to the latest commit).
You need to either wait for Andrew to update the dependency or to manually checkout master branch of scopehal repo.

--- End quote ---
This might be the case. Unfortunately I don't really know what I'm doing, just following documentation step by step, so I'll wait.

azonenberg:

--- Quote from: Antonio90 on September 14, 2024, 07:53:38 pm ---Then the terminal just returns "ERROR: Unknown scope type"

--- End quote ---

Try again with the latest version on git, should have the 800 series support merged?

Antonio90:

--- Quote from: azonenberg on September 14, 2024, 09:28:56 pm ---
--- Quote from: Antonio90 on September 14, 2024, 07:53:38 pm ---Then the terminal just returns "ERROR: Unknown scope type"

--- End quote ---

Try again with the latest version on git, should have the 800 series support merged?

--- End quote ---

Thanks! Compiling now.

EDIT: Compiled and working (on Windows still). Thank you very much Andrew and @fredo_! Will test more tomorrow, it's already 1:45 AM here, and I need sleep. The "filter" section with the block programming interface is just genius BTW, really impressive piece of software.

fredo_:

--- Quote from: Antonio90 on September 14, 2024, 10:38:42 pm ---it's already 1:45 AM here, and I need sleep..

--- End quote ---
Same here, time to go to bed!

Furna:

--- Quote from: egonotto on September 12, 2024, 04:16:29 pm ---
--- Quote from: macaba on September 12, 2024, 02:34:55 pm ---Try

cd build
cmake --build . -j4

--- End quote ---

Hello,

Thanks it compiles now, but it's taking quite a while.

--- End quote ---

The "-j4" tells the compiler (ninja) to use 4 cores on your PC.
It is more than probable that your PC has more than 4 cores.
ninja by default uses all your available cores.
In short run "cmake --build ." without the "j" switch.
Please note that cmake in turn runs ninja => just run "ninja" as fredo_ suggested and advised in the yet unpublished doc mentioned by azonenberg


--- Quote from: egonotto on September 12, 2024, 04:16:29 pm ---Best regards
egonotto
PS: Now it's ready. But my SDS3000X HD is not recognized correctly via LAN.
ERROR: Unknown scope type

--- End quote ---


--- Quote from: azonenberg on September 14, 2024, 09:28:56 pm ---
--- Quote from: Antonio90 on September 14, 2024, 07:53:38 pm ---Then the terminal just returns "ERROR: Unknown scope type"

--- End quote ---

Try again with the latest version on git, should have the 800 series support merged?

--- End quote ---

Yup it is merged and seems to work.
I just cloned and compiled from scratch and  Siglent SDS824X HD is recognized ... I didn't try yet to really take a capture.
Wil let you know when I had it tested better.

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod