[SOLVED] Please help my brick Hantek DSO1062B at the day after I purchased!

[xthanhn]

Hi everyone,

Firstly, I am sorry about my english! Thank you very much!

I have just bought a hantek DSO1062B with hardware version and serial number as below picture




I made a backup as instruction of Mr.Tinhead in this link: https://www.eevblog.com/forum/testgear/hantek-tekway-dso-hack-get-200mhz-bw-for-free/msg86825/#msg86825
Solder UART pin.



After made some stupid things, I have chosen wrong file to download to uboot in supervivi menu and the device could not boot again. Nothing shows on UART when the device turned on

I search in the internet, buy a J-Link and download supervivi to NAND flash through SDRam and the UART come back 
I try to restore the backup which I have made from the begin but without success.

The backup in Tinhead's guide has only 3 files: boot.bin, kernel.bin and root.bin
But mine is 4 files: boot.bin, kernel.bin, root.bin and root2.bin 

I try to combine them by this command:

copy /B boot.bin + blank.bin + kernel.bin + root.bin + root2.bin + mizi_tag.bin fw_backup.bin

But the file "fw_backup.bin" is only 68.361.216 bytes while fw_backup.bin in TinHead's guide is 69.206.016 bytes, So the restore can not complete, it stands at 99% and can not boot too. (https://www.eevblog.com/forum/testgear/hantek-tekway-dso-hack-get-200mhz-bw-for-free/msg75015/#msg75015) 



When add more space to blank.bin file to get right size 69.206.016 bytes, the restore is completed but the device can not work too.



The problem is:
- How I combine the backup files to restore through supervivi
- Does anyone have backup bin file in 1 file only? Please send me.
- I have tried to write to NAND through openocd and J-Link but timeout, can not write 65.1MB to NAND
- How can I make the device work again?


I receive it in the morning and it stops working in the evening. It has been a week from now. I haven't used it to measure at least 1 time haha 

Does anyone have any ideas? Please help me to solve this problem.

Thank you very much  I have tried to do a lot of things but no luck 

[xthanhn]

#UPDATE

I have just restored dso_ready.bin to my DSO1062B, it can boot into linux. What can I do now?
I really need a complete backup bin file of DSO1062B, does anyone have it? 

Code: [Select]


##### EmbedSky BIOS for SKY2440/TQ2440 #####
Press Space key to Download Mode !
Booting Linux ...
Copy linux kernel from 0x00200000 to 0x30008000, size = 0x00200000 ... Copy Kernel to SDRAM done,NOW, Booting Linux......
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.30.4 (root@localhost.localdomain) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-176) ) #17 Sun Oct 9 14:24:29 CST 2011
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: TQ2440
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0
NR_IRQS:85
irq: clearing pending ext status 00080100
irq: clearing subpending status 00000003
irq: clearing subpending status 00000002
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61316KB available (3116K code, 333K data, 100K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 199.47 BogoMIPS (lpj=498688)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 296 bytes
NET: Registered protocol family 16
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4808000, irq 33
DMA channel 1 at c4808040, irq 34
DMA channel 2 at c4808080, irq 35
DMA channel 3 at c48080c0, irq 36
S3C244X: Clock Support, DVS off
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
yaffs Sep 30 2011 10:36:32 Installing.
msgmni has been set to 119
alg: No test for stdrng (krng)
io scheduler noop registered (default)
s3c2440-uart.0: tq2440_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: tq2440_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: tq2440_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=2, 20ns Twrph0=3 30ns, Twrph1=2 20ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "EmbedSky_Board_uboot"
0x000000200000-0x000000400000 : "EmbedSky_Board_kernel"
0x000000400000-0x000003ff8000 : "EmbedSky_Board_yaffs2"
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
mice: PS/2 mouse device common for all mice
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
Linux video capture interface: v2.00
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: starting watchdog timer
s3c2410-wdt s3c2410-wdt: watchdog active, reset abled, irq enabled
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: powered down.
s3c2440-sdi s3c2440-sdi: initialisation done.
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI UDA134X
No device for DAI s3c24xx-i2s
S3C24XX_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: UDA134X <-> s3c24xx-i2s mapping ok
s3c2440-sdi s3c2440-sdi: powered down.
ALSA device list:
  #0: S3C24XX_UDA134X (UDA134X)
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
s3c2410-rtc s3c2410-rtc: setting system clock to 2021-01-23 14:45:23 UTC (1611413123)
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs_read_super: isCheckpointed 0
VFS: Mounted root (yaffs filesystem) on device 31:2.
Freeing init memory: 100K
__init s3c24xxfb_probe
setting vert: up=26, low=4, sync=2
setting horz: lft=4, rt=14, sync=32
s3c2410fb_activate_var
S3C2410_LCDCON1_CLKVAL(default_display->setclkval)=1
Console: switching to mono frame buffer device 100x30
fb0: s3c2410fb frame buffer device
lcd_init
dso-lcd1 initialized
var.xres=800
var.yres=480
var.bits_per_pixel=8
var.xres_virtual=800
var.yres_virtual=480
fix.id=s3c2410fb
fix.smem_start=866123776
fix.smem_len=768000
fix.type=0
fix.type_aux=0
fix.xpanstep=0
fix.ypanstep=0
fisetting vert: up=18, low=13, sync=3
setting horz: lft=20, rt=6, sync=38
s3c2410fb_activate_var
S3C2410_LCDCON1_CLKVAL(default_display->setclkval)=1
x.ywrapstep=0
fix.line_length=800
argv[1]=16
var.xres=800    var.yres=480    var.bits_per_pixel=16
show logo,video_buf_size = 768000
bwscon:0x2201d110
fpga bank 221422
dso-fpga: install ok
bwscon:0x2201d110
fpga bank 221422
dso-fpga-la: install ok
dso-spi initialized
Init spi success!
New Log Write OK Length:21
dso-spi-la initialized
Init spi success!
New Log Write OK Length:21
s3c2440_clkcon=00FE7FF0
fpga download file_name :/dn.rbf
status: 0x1
fpga_down_load file name : /dn.rbf.
data DOWN finish.
dso-spi:FPGA_DOWNLOAD ok.
release
s3c2440_clkcon=00FE7FF0
fpga download file_name :/la_top.rbf
In spi_ioctl:arg=-1096999046
copy-from-user ok
dn_file_name:/la_top.rbf
in opt-download-fpga
nconfig: 0x1
status: 0x1
fpga_down_load file name : /la_top.rbf.
data DOWN finish.
dso-spi-la:FPGA_DOWNLOAD ok.
release
dm9000 Ethernet Driver, V1.31
dm9000 dm9000.0: read wrong id 0x002affff
dm9000 dm9000.0: read wrong id 0xffffdfff
dm9000 dm9000.0: read wrong id 0xffffffff
dm9000 dm9000.0: read wrong id 0x2b2affff
dm9000 dm9000.0: read wrong id 0xffffffff
dm9000 dm9000.0: read wrong id 0xffffffff
dm9000 dm9000.0: read wrong id 0xffffffff
dm9000 dm9000.0: read wrong id 0x2b2a2928
dm9000 dm9000.0: wrong id: 0x2b2a2928
dm9000 dm9000.0: not found (-19).
Try to bring eth0 interface up ...
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCSIFHWADDR: No such device
ifconfig eth0 hw ether 10:23:45:67:89:ab
Hantek GPIO(buzzer/speaker),(c)20110309
gpioG11 initialized
speaker on
ifconfig: SIOCSIFADDR: No such device
ifconfig eth0 192.168.100.155 netmask 255.255.255.0 up
/sbin/net_set: line 5: route: not found
add default gw 192.168.100.255
Done
Beep
dso-buzzer initialized
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c: slave address 0x10
pdata->frequency=6000
s3c2440-i2c s3c2440-i2c: bus frequency set to 9 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
s3c2410_udc: debugfs dir creation failed -19
s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes
g_serial gadget: Gadget Serial v2.4
g_serial gadget: g_serial ready
s3c2440_clkcon=00FF7FF0
fpga download file_name :/dn.rbf
status: 0x1
fpga_down_load file name : /dn.rbf.
data DOWN finish.
dso-spi:FPGA_DOWNLOAD ok.
release
no update file to foud
now run app .....
var.xres=800
var.yres=480
var.bits_per_pixel=16
var.xres_virtual=800
var.yres_virtual=480
fix.id=s3c2410fb
fix.smem_stsetting vert: up=26, low=4, sync=2
setting horz: lft=4, rt=14, sync=32
s3c2410fb_activate_var
S3C2410_LCDCON1_CLKVAL(default_display->setclkval)=1
art=866123776
fix.smem_len=768000
fix.type=0
fix.type_aux=0
fix.xpanstep=0
fix.ypanstep=0
fix.ywrapstep=0
fix.line_length=1600
argv[1]=8
var.xres=800    var.yres=480    var.bits_per_pixel=8

Please press Enter to activate this console. mkdir: can't create directory '/param': File exists
mkdir: can't create directory '/param/sav': File exists
mkdir: can't create directory '/param': File exists
mkdir: can't create directory '/param/sav': File exists
s3c2440_clkcon=00FF7FF0
now pwm_value:0
now pwm_value:56
▒*** Warning - bad CRC or NAND, using default environment



##### EmbedSky BIOS for SKY2440/TQ2440 #####
Press Space key to Download Mode !
Booting Linux ...
Copy linux kernel from 0x00200000 to 0x30008000, size = 0x00200000 ... Copy Kernel to SDRAM done,NOW, Booting Linux......
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.30.4 (root@localhost.localdomain) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-176) ) #17 Sun Oct 9 14:24:29 CST 2011
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: TQ2440
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0
NR_IRQS:85
irq: clearing pending ext status 00080100
irq: clearing subpending status 00000003
irq: clearing subpending status 00000002
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61316KB available (3116K code, 333K data, 100K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 199.47 BogoMIPS (lpj=498688)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 296 bytes
NET: Registered protocol family 16
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4808000, irq 33
DMA channel 1 at c4808040, irq 34
DMA channel 2 at c4808080, irq 35
DMA channel 3 at c48080c0, irq 36
S3C244X: Clock Support, DVS off
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
yaffs Sep 30 2011 10:36:32 Installing.
msgmni has been set to 119
alg: No test for stdrng (krng)
io scheduler noop registered (default)
s3c2440-uart.0: tq2440_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: tq2440_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: tq2440_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=2, 20ns Twrph0=3 30ns, Twrph1=2 20ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "EmbedSky_Board_uboot"
0x000000200000-0x000000400000 : "EmbedSky_Board_kernel"
0x000000400000-0x000003ff8000 : "EmbedSky_Board_yaffs2"
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
mice: PS/2 mouse device common for all mice
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
Linux video capture interface: v2.00
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: starting watchdog timer
s3c2410-wdt s3c2410-wdt: watchdog active, reset abled, irq enabled
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: powered down.
s3c2440-sdi s3c2440-sdi: initialisation done.
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI UDA134X
No device for DAI s3c24xx-i2s
S3C24XX_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: UDA134X <-> s3c24xx-i2s mapping ok
s3c2440-sdi s3c2440-sdi: powered down.
ALSA device list:
  #0: S3C24XX_UDA134X (UDA134X)
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
s3c2410-rtc s3c2410-rtc: setting system clock to 2021-01-23 14:46:53 UTC (1611413213)
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs_read_super: isCheckpointed 0
VFS: Mounted root (yaffs filesystem) on device 31:2.
Freeing init memory: 100K
llkil^Ckiall dso__init s3c24xxfb_probe
setting vert: up=26, low=4, sync=2
setting horz: lft=4, rt=14, sync=32
s3c2410fb_activate_var
S3C2410_LCDCON1_CLKVAL(default_display->setclkval)=1
Console: switching to mono frame buffer device 100x30
fb0: s3c2410fb frame buffer device
lcd_init
dso-lcd1 initialized
dvar.xres=800
var.yres=480
var.bits_per_pixel=8
var.xres_virtual=800
var.yres_virtual=480
fix.id=s3c2410fb
fix.smem_start=866123776
fix.smem_len=768000
fix.type=0
fix.type_aux=0
fix.xpanstep=0
fix.ypanstep=0
fisetting vert: up=18, low=13, sync=3
setting horz: lft=20, rt=6, sync=38
s3c2410fb_activate_var
S3C2410_LCDCON1_CLKVAL(default_display->setclkval)=1
x.ywrapstep=0
fix.line_length=800
argv[1]=16
var.xres=800    var.yres=480    var.bits_per_pixel=16
show logo,video_buf_size = 768000

bwscon:0x2201d110
fpga bank 221422
dso-fpga: install ok
bwscon:0x2201d110
fpga bank 221422
dso-fpga-la: install ok
dso-spi initialized
Init spi success!
New Log Write OK Length:21
dso-spi-la initialized
Init spi success!
New Log Write OK Length:21
s3c2440_clkcon=00FE7FF0
fpga download file_name :/dn.rbf
status: 0x1
fpga_down_load file name : /dn.rbf.
kialldata DOWN finish.
dso-spi:FPGA_DOWNLOAD ok.
release
s3c2440_clkcon=00FE7FF0
fpga download file_name :/la_top.rbf
In spi_ioctl:arg=-1090797702
copy-from-user ok
dn_file_name:/la_top.rbf
in opt-download-fpga
nconfig: 0x1
status: 0x1
fpga_down_load file name : /la_top.rbf.                                                                          data DOWN finish.
dso-spi-la:FPGA_DOWNLOAD ok.
release
dm9000 Ethernet Driver, V1.31
dm9000 dm9000.0: read wrong id 0x002a0028
dm9000 dm9000.0: read wrong id 0x2b2a2928
dm9000 dm9000.0: read wrong id 0xffffffff
dm9000 dm9000.0: read wrong id 0xffffffff
dm9000 dm9000.0: read wrong id 0xffffffff
dm9000 dm9000.0: read wrong id 0x6993bfaa
dm9000 dm9000.0: read wrong id 0x2b2a2928
dm9000 dm9000.0: read wrong id 0xff8d6c91
dm9000 dm9000.0: wrong id: 0xff8d6c91
dm9000 dm9000.0: not found (-19).
Try to bring eth0 interface up ...
ifconfig: SIOCGIFFLAGS: No such device
Hantek GPIO(buzzer/speaker),(c)20110309
gpioG11 initialized
speaker on
ifconfig: SIOCSIFHWADDR: No such device
ifconfig eth0 hw ether 10:23:45:67:89:ab
kifconfig: SIOCSIFADDR: No such device
ifconfig eth0 192.168.100.155 netmask 255.255.255.0 up
/sbin/net_set: line 5: route: not found
add default gw 192.168.100.255
Done
Beep
dso-buzzer initialized
illi2c /dev entries driver
as3c2440-i2c s3c2440-i2c: slave address 0x10
pdata->frequency=6000
s3c2440-i2c s3c2440-i2c: bus frequency set to 9 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
llInitializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
s3c2410_udc: debugfs dir creation failed -19
 s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes
dg_serial gadget: Gadget Serial v2.4
g_serial gadget: g_serial ready
ss3c2440_clkcon=00FF7FF0
fpga download file_name :/dn.rbf
status: 0x1
fpga_down_load file name : /dn.rbf.
o
data DOWN finish.
dso-spi:FPGA_DOWNLOAD ok.
release
no update file to foud
now run app .....
var.xres=800
var.yres=480
var.bits_per_pixel=16
var.xres_virtual=800
var.yres_virtual=480
fix.id=s3c2410fb
fix.smem_stasetting vert: up=26, low=4, sync=2
setting horz: lft=4, rt=14, sync=32
s3c2410fb_activate_var
S3C2410_LCDCON1_CLKVAL(default_display->setclkval)=1
rt=866123776
fix.smem_len=768000
fix.type=0
fix.type_aux=0
fix.xpanstep=0
fix.ypanstep=0
fix.ywrapstep=0
fix.line_length=1600
argv[1]=8
var.xres=800    var.yres=480    var.bits_per_pixel=8

Please press Enter to activate this console. [root@Hantek /]# kikillall dso
-/bin/sh: kikillall: not found
[root@Hantek /]# kimkdir: can't create directory '/param': File exists
mkdir: can't create directory '/param/sav': File exists
llmkdir: can't create directory '/param': File exists
mkdir: can't create directory '/param/sav': File exists
s3c2440_clkcon=00FF7FF0
now pwm_value:0
all dnow pwm_value:56
sdo
killall: dsdo: no process killed
[root@Hantek /]# killall dso
killall: dso: no process killed
[root@Hantek /]# killall dsod
[root@Hantek /]# release
sync
save exit: isCheckpointed 0
[root@Hantek /]# cp /mnt/udisk/dso.exe /
cp: can't stat '/mnt/udisk/dso.exe': No such file or directory
[root@Hantek /]# mount -f /mnt/udisk
mount: can't find /mnt/udisk in /etc/fstab
[root@Hantek /]# ls /etc/fstab
/etc/fstab
[root@Hantek /]# fstab
-/bin/sh: fstab: not found
[root@Hantek /]# /etc/fstab
-/bin/sh: /etc/fstab: Permission denied
[root@Hantek /]# cd /mnt/udisk
[root@Hantek udisk]# ls
[root@Hantek udisk]# cd ..
[root@Hantek /mnt]# ls
sd     udisk
[root@Hantek /mnt]# cd udisk
[root@Hantek udisk]# ;s
-/bin/sh: syntax error: unexpected ";"
[root@Hantek udisk]# ls
[root@Hantek udisk]# ls -i
[root@Hantek udisk]# ls -li
total 0
[root@Hantek udisk]# cd ..
[root@Hantek /mnt]# ls
sd     udisk
[root@Hantek /mnt]# cd ..
[root@Hantek /]# ls
OurLanguages     fpgabank.conf    logotype         sendspi-la
bin              help.db          logotype.dis     sys
cur_acq.type     home             lost+found       sys.inf
dev              i2c.log          mnt              tmp
disk_sta.info    icon             msg              tmpdst
dn.rbf           keyprotocol.inf  opt              tmpp
dso              la_top.rbf       param            usr
dso-fpga-bak.ko  language.img     proc             var
dso.exe          lib              protocol.inf
dst1202b         linuxrc          root
etc              logo             sbin
[root@Hantek /]#



[xthanhn]

Any one? 

[YetAnotherTechie]

If it's so new why don't you return it and pretend "it broke"?
You have 4 .bin files. I supose you need to flash one to each partition, but you are combining them and trying to send as one file 

[Fungus]

If it's so new why don't you return it and pretend "it broke"?

Because he has a conscience...?

[xthanhn]

If it's so new why don't you return it and pretend "it broke"?
You have 4 .bin files. I supose you need to flash one to each partition, but you are combining them and trying to send as one file 

Thank you for your idea but it is my fault 

I have try to flash one by one to each partition but I can not work at all.

[xthanhn]

If it's so new why don't you return it and pretend "it broke"?

Because he has a conscience...?

Thank you
My stupid problem has been solved 

[xthanhn]

I have contacted Hantek and after 3 days, they send me the factory file than my DSO1062B works again  Thank Caiyijun from Hantek!
If anyone has problem with similar model, p.m me, I will help if I can. Thank you all.

Weird is they send 1202BV firmware
Then I dont need to hack from 1062B to 1202BV at all haha 

ps: caiyijun@hantek.com in case anyone needs.

[Shiv]

Factory repair hack

[serjik69]

Hi xthanhn! Can you share or give me the firmware from 1202 for my 1062. My 1062 fails self-test, fails at step 23, maybe flashing to a newer version will fix the problem. Thank you very much