| Products > Test Equipment |
| Question: Cheap pure sine wave genertor 1khz? |
| << < (5/19) > >> |
| Fungus:
--- Quote from: innkeeper on January 10, 2020, 09:57:22 pm --- --- Quote from: Gyro on January 10, 2020, 10:49:03 am ---You might get better than the quoted -124dB with some careful component value matching anyway... --- End quote --- i've actually ordered one of these .. figured its a start and maybe i can tweak it. --- End quote --- Ok, so -124dB is only "a start"? Got it. :-+ :-DD |
| innkeeper:
--- Quote from: MasterT on January 10, 2020, 10:53:54 pm --- (Attachment Link) I've build one recently, to test my 18-bits differential AD7984 board. I changed OPA to LM4562, and use 7370-18V-0.04mA lamp. Circuits does need "manual" tuning to get the lowest THD, but accounting simplicity it's not an obstacle. Results thd-2 ~0.0004% (-110dB) and thd-3 ~0.0002 (-114dB) at 4kHz. Not sure about 100kHz, ADC itself has thd-3 ~0.002% at this frequency. --- End quote --- that is amazing for such a simple circuit, i;ll have to throw that together and put it on the analyzer and check it out. thanks |
| innkeeper:
i've hit up victor from the diyaudio forum to see if he has any of his boards available. he is getting better then -150 Db. |
| MasterT:
--- Quote from: innkeeper on January 11, 2020, 03:13:46 am ---i've hit up victor from the diyaudio forum to see if he has any of his boards available. he is getting better then -150 Db. --- End quote --- What circuits? I've seen link to e-b https://www.ebay.com/itm/Low-Distortion-Audio-Range-Oscillator-1KHz-Sine-Wave-Signal-Generator-PCB-Board/262844562138, let's call it JFET-Wein, description says: --- Quote ---Low distortion coefficient of the sinusoidal oscillator circuit board, oscillation frequency: 1KHz, low distortion, distortion factor 0.0064% (- 124dB) --- End quote --- doesn't look right, in my math -120dB is 0.0001% ( or 1ppm), 0.0064% is about -84-85 dB, worse than cheapest sound card has. And NE5532 ? Common, be serious. Or is it CdS-Wein? http://www.redcircuits.com/Page82.htm Probably, just simplified version of https://www.analog.com/en/design-center/evaluation-hardware-and-software/evaluation-boards-kits/dc1858a.html#eb-overview I trust AD, performance is outstanding, but same with a price and complexity. Though -120 only: Table 1. Amplitude and Offset Options for DC1858A (SNR and THD Taken at f OSC = 2kHz) Range (V) R22 (kΩ) R18 (kΩ) C11 (μF) Sine Out (V P-P ) Offset (V) SNR (dB)* THD (dB)* 0 to 2.5 14 36.5 0.47 2.25 1.25 100 –119 0.5 to 4.5 22.6 12.1 0.47 3.6 2.5 103 –121 0 to 4.096 23.2 17.4 0.47 3.7 2.048 103 –121 0 to 5 28 12.1 0.47 4.5 2.5 104 –118 ±2.5 28 ∞ 0.47 4.5 0 104 –119 ±5 56.2 ∞ 0.47 9 0 107 –117 ±10 118 ∞ 0.1 18 0 100 –107 page 3 https://www.analog.com/media/en/dsp-documentation/evaluation-kit-manuals/dc1858af.pdf And most resistors precise 0.1% tolerance, they can't get -120dB with CdS even for single Tone generator using common 1% parts, and adjustable frequency doesn't go along with precision parts at all. |
| innkeeper:
@masterT victor sells is an updated version of this: https://www.diyaudio.com/forums/equipment-and-tools/205304-low-distortion-audio-range-oscillator-21.html#post3116055 update: i think this is the latest schematic https://www.diyaudio.com/forums/equipment-and-tools/205304-low-distortion-audio-range-oscillator-743.html#post5873578 i am sure there is a more up to date schematic in that thread, but that thread is over 8000 messages long here is the web page he put up just wiht the specs https://viccc42.wixsite.com/uld-audio |
| Navigation |
| Message Index |
| Next page |
| Previous page |