| Products > Test Equipment |
| Ridiculously small Rigol DS1000z series font size |
| << < (28/35) > >> |
| markone:
--- Quote from: miguelvp on January 29, 2016, 03:33:58 pm ---of course the DISP command might be a special case because the scope might not be too busy. So depending what the scope is doing the waveforms probably hinders the transfer rate. --- End quote --- Honestly i never tinkered around this scope for external control, it was enough for me to take occasional snapshots on usb flash key, while i played a lot with front panel controls. I saw in other threads that lot of work has been done around DS1000Z boards by some capable guys that have already sniffed & scanned spotting lot of important things, i'm wondering if the command interface parser table is fully readable or is buried encrypted in the flash dumps. There is still margin to discover new commands ? |
| markone:
--- Quote from: miguelvp on January 29, 2016, 07:28:07 pm ---Have you tried this one btw? https://www.eevblog.com/forum/testgear/free-ds6000ds1000z-software/ I haven't had a chance to use it yet, comes with full source --- End quote --- Thanks a lot for the hint, i will give a try later. |
| miguelvp:
--- Quote from: markone on January 29, 2016, 07:45:55 pm --- --- Quote from: miguelvp on January 29, 2016, 03:33:58 pm ---of course the DISP command might be a special case because the scope might not be too busy. So depending what the scope is doing the waveforms probably hinders the transfer rate. --- End quote --- Honestly i never tinkered around this scope for external control, it was enough for me to take occasional snapshots on usb flash key, while i played a lot with front panel controls. I saw in other threads that lot of work has been done around DS1000Z boards by some capable guys that have already sniffed & scanned spotting lot of important things, i'm wondering if the command interface parser table is fully readable or is buried encrypted in the flash dumps. There is still margin to discover new commands ? --- End quote --- There is a programmer manual: DS2000 series: http://assets.tequipment.net/assets/1/26/Documents/Rigol/DS2072/ds2072_doc_5.pdf MSO1000z/DS1000z series: http://www.batronix.com/pdf/Rigol/ProgrammingGuide/MSO1000Z_DS1000Z_ProgrammingGuide_EN.pdf There might be new commands added on the firmware as they now support CAN bus on some scopes, but overall those docs have most of the commands, maybe there are others but you can look at all the Rigol threads and probably they are already found by others. |
| Karel:
--- Quote from: miguelvp on January 30, 2016, 01:39:23 am ---MSO1000z/DS1000z series: http://www.batronix.com/pdf/Rigol/ProgrammingGuide/MSO1000Z_DS1000Z_ProgrammingGuide_EN.pdf There might be new commands added on the firmware as they now support CAN bus on some scopes, but overall those docs have most of the commands, maybe there are others but you can look at all the Rigol threads and probably they are already found by others. --- End quote --- That one is from September 2014. Since there has been some firmware updates, the programming guide has been updated as well. The latest is from July 2015 and you can download it from the Rigol website. Technical documents should always be downloaded from the source, not from some shop. |
| markone:
--- Quote from: miguelvp on January 30, 2016, 01:39:23 am --- There might be new commands added on the firmware as they now support CAN bus on some scopes, but overall those docs have most of the commands, maybe there are others but you can look at all the Rigol threads and probably they are already found by others. --- End quote --- Those threads are so huuuge, i was hoping to gain a summary ;-) Of course i'm aware of official programming guide but i was referring to unknown commands kept "secret" by Rigol. I think that DZ1000Z scopes have enough power to be turned in a great remote USB scope, but i would bet that this is not what Rigol want. |
| Navigation |
| Message Index |
| Next page |
| Previous page |