Products > Test Equipment

RuiDeng Riden RD6006P DC power supply

<< < (3/10) > >>

niekproductions:
@UniSoft

This looks very promising! Any measurements on load transients (voltage excursions upon applying a positive and negative load step)?
I'm curious how the linear end stage handles that.

UniSoft:
@niekproductions


--- Quote from: niekproductions on May 27, 2021, 01:11:39 pm ---Any measurements on load transients (voltage excursions upon applying a positive and negative load step)?
I'm curious how the linear end stage handles that.

--- End quote ---
You can see review, but in russian (use google translator)
https://mysku.ru/blog/aliexpress/85343.html
https://translate.google.com/translate?sl=ru&tl=en&u=https://mysku.ru/blog/aliexpress/85343.html

niekproductions:

--- Quote from: UniSoft on May 27, 2021, 04:10:20 pm ---You can see review, but in russian (use google translator)
https://mysku.ru/blog/aliexpress/85343.html
https://translate.google.com/translate?sl=ru&tl=en&u=https://mysku.ru/blog/aliexpress/85343.html

--- End quote ---

That is a very comprehensive review, thank you! Ordered one right away :D

duckduck:

--- Quote from: AaronR on February 04, 2021, 09:27:23 pm ---There is a driver you may need to download and install if you're on windows 10 standby,  I'll see which one it is.
OK I just looked this is the one that worked for me to get USB port working.
CH341SER
http://www.wch-ic.com/downloads/CH341SER_EXE.html

In my case my laptop connected no problem but I needed this serial to usb driver installed on the desktop.

--- End quote ---

Bought a RD6006P and was unable to connect to it via USB. Windows 10 version 21H1 running on x64.
Thank you AaronR (in the main RD6006 thread), installing the driver worked for me. I now see that the driver has loaded for my USB serial device. Hey people, make sure to select the new COM port that gets added. I wish Ruideng would make a note of this driver in their docs so I didn't waste time  |O

EDIT:

I installed the latest UniSoft firmware (1.38.1a). Looks good so far. I really like that I can read the input voltage now (it is larger) and it has an additional digit. Thank you UniSoft for your work!

UniSoft posts his firmwares in the main RD6006P thread. Here is the latest (the 60065 is for the RD6006P). Click on the link to go to his post where the firmware files are attached:


--- Quote from: UniSoft on May 30, 2021, 04:37:21 pm ---New BETA versions (p)
And new alpha (a) version for RD6006P

--- End quote ---

How do you install the UniSoft firmware? How do you use the new UI? sunkmail has you covered. Thank you sunkmail (et al.) for your work!


--- Quote from: sunkmail on February 25, 2021, 06:14:03 pm ---Hi Everyone,

I have been working on a reference document / manual for using the RD60xx series of power supplies loaded with UniSoft's custom firmware.

        RD60xx Custom Firmware Reference


<SNIP>

--- End quote ---

duckduck:

--- Quote from: Algasman on May 05, 2021, 06:57:07 pm ---Looks like an impressive piece of hardware!
Can some owner say something about the fan noise? Are the fans temperature controlled? (yes, but on/off or the hotter the faster?)
Three in total can make a lot of noise.

--- End quote ---

Fan in the back of the case that is sold for the unit is normally off until things get fairly warm, then it switches to low speed, then if the unit gets very hot it switches to high speed. The only way I can get it to high speed is to run it at full power 60V, 6A into my DC load which has a loud fan, and the RD is not very loud in comparison. Of course everything is easy to get to in the case so you can modify it however you like or use a different case / power supply / fan entirely.

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod