Products > Test Equipment
Siglent .ads firmware file format
nicolad:
--- Quote from: tv84 on October 04, 2018, 09:02:12 pm ---How to open a telnet session in a Siglent when the root password is unknown?
Use the following scripts, according to each equipment.
They provide a root session via port 10101.
--- End quote ---
How do they work? Trying the one for SDG2000X but firmware update fails. Port 10101 is closed...
joeyjoejoe:
--- Quote from: tv84 on September 17, 2018, 09:35:22 pm ---
--- Quote from: janekivi on April 08, 2017, 10:40:18 am ---I can make the same trick here like when I was uploading LeCroy in to SDG1025
but who can try this and there may be the same check routine and instrument
will say "Not supported firmware, please reflash correct. Otherwise I will wait 15 min".
This is stupid, it will wait that time anyway before you can access flash menu...
So... do not be the first who is using this firmware file on SPD3303X-E
but this first hack may be needed to be tried out by someone.
SPD3303X-V100R001B01D02P03_with _E_header.zip
OK, I give this only individually after request. I can't test it.
--- End quote ---
A year ago nobody volunteered to confirm Janekivi's work so I resuscitated the challenge and was successfull! :popcorn:
Attached is the proof of a Siglent SPD3303X-E conversion to a SPD3303X model.
The method is simple:
1. Run the SCPI command in the X-E to enable the 1mV step:
FACTORY ON
2. Using EasyPower flash the required FW file from the attached ZIP. (ConvertFromX-E)
(3. If you want to rollback, flash the other file.)
The FWs are Siglent official versions with Prod_ID's swapped like janekivi suggested.
The HW version of the board where the test was done is 0.3.
ATTENTION: This may involve a certain risk so do it at your own responsability!
Enjoy!
--- End quote ---
Does the FACTORY ON have any feedback? Or after hitting "Query" it's OK that nothing is output?
tautech:
--- Quote from: joeyjoejoe on October 11, 2018, 12:38:56 am ---
--- Quote from: tv84 on September 17, 2018, 09:35:22 pm ---
--- Quote from: janekivi on April 08, 2017, 10:40:18 am ---I can make the same trick here like when I was uploading LeCroy in to SDG1025
but who can try this and there may be the same check routine and instrument
will say "Not supported firmware, please reflash correct. Otherwise I will wait 15 min".
This is stupid, it will wait that time anyway before you can access flash menu...
So... do not be the first who is using this firmware file on SPD3303X-E
but this first hack may be needed to be tried out by someone.
SPD3303X-V100R001B01D02P03_with _E_header.zip
OK, I give this only individually after request. I can't test it.
--- End quote ---
A year ago nobody volunteered to confirm Janekivi's work so I resuscitated the challenge and was successfull! :popcorn:
Attached is the proof of a Siglent SPD3303X-E conversion to a SPD3303X model.
The method is simple:
1. Run the SCPI command in the X-E to enable the 1mV step:
FACTORY ON
2. Using EasyPower flash the required FW file from the attached ZIP. (ConvertFromX-E)
(3. If you want to rollback, flash the other file.)
The FWs are Siglent official versions with Prod_ID's swapped like janekivi suggested.
The HW version of the board where the test was done is 0.3.
ATTENTION: This may involve a certain risk so do it at your own responsability!
Enjoy!
--- End quote ---
Does the FACTORY ON have any feedback?
--- End quote ---
Five not four digits on the PSU display. ;)
joeyjoejoe:
After FACTORY ON cmd is sent
PSU is no longer responsive via EasyPower - cannot do any sort of commands. Re-connecting to the device re-enables functionality.
Also, is this a "Normal Mode" FW update, or "Firmware mode"?
tautech:
Reboot PSU.
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version