| Products > Test Equipment |
| Siglent .ads firmware file format |
| << < (81/85) > >> |
| gman76:
I have the scopes at the office on a corporate network. There’s a sneaky way to copy a file from the PC to an external usb drive so that it doesn’t get encrypted. Involves the file extension. |
| voronin_10:
Hi friend, i have bad osciloscome, a need to decompres ads file to arhive my osciloscp after flashing as brick, but U-boot is alive annd need 3 files this is console out: --- Code: ---Download Linux from USB to Nandflash... reading ro_uImage ** Unable to read file ro_uImage ** reading rootfs.img ** Unable to read file rootfs.img ** reading datafs.img ** Unable to read file datafs.img ** reading logo.bmp ** Unable to read file logo.bmp ** Booting from nand ... --- End code --- how to mount or extract this files of the update file? https://siglentna.com/download/15283/ siglent sds1102cml+ good update log --- Code: ---[00] U-Boot SPL 2013.01.01-svn29730 (Mar 27 2017 - 19:02:34) config ddr_pll_config()++ config ddr_pll_config()-- nand_init+++++ nand_init----- Lcd_Init()++ SetUpLCD()++ SetUpLCD()-- len=768052, height=480, width=800 Logo from nandflash: base=0x81000000; end=0x810bb81f; end-base=0xbb81f; rwsize=0xbb820; r=0x0 Lcd_Init()-- U-Boot 2013.01.01-svn29730 (Mar 27 2017 - 19:02:34) I2C: ready DRAM: 128 MiB NAND: 256 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Using default environment set_default_env::7864 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: <ethaddr> not set. Validating first E-fuse MAC cpsw Hit any key to stop autoboot (Re)start USB... USB0: scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Download Linux from USB to Nandflash... reading ro_uImage ** Unable to read file ro_uImage ** reading rootfs.img ** Unable to read file rootfs.img ** reading datafs.img ** Unable to read file datafs.img ** reading logo.bmp ** Unable to read file logo.bmp ** Booting from nand ... NAND read: device 0 offset 0x3080000, size 0x300000 3145728 bytes read: OK ## Booting kernel from Legacy Image at 80200000 ... Image Name: Linux-3.2.0+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2157768 Bytes = 2.1 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. init started: BusyBox v1.13.2 (2012-04-08 17:28:57 CDT) starting pid 519, tty '': '/etc/init.d/rcS' rS in /etc/init.d/rcS: line 15: setterm: not found starting pid 536, tty '/dev/ttyO0': '-/bin/sh' Processing /etc/profile... Done / # check_and_upgrade:starting... mount_fs: rw,sync,ubi1_0,/usr/bin/siglent/usr ubi1_0unattached attach_ubi:datafs attach_ubi:11 UBI device number 1, total 812 LEBs (103104512 bytes, 98.3 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) MOUNT_DIR_NAME = /usr/bin/siglent/usr TEST_RESTURN = is_fs_mounted 0 --- is_need_upgrade is_need_upgrade:not need upgrade check_and_upgrade:end... ++mount_check_copy_appdata: starting mount_fs: ro,sync,ubi2_0,/usr/bin/siglent/firmdata0 ubi2_0unattached attach_ubi:firmdata0 attach_ubi:9 UBI device number 2, total 400 LEBs (50790400 bytes, 48.4 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) MOUNT_DIR_NAME = /usr/bin/siglent/firmdata0 TEST_RESTURN = is_fs_mounted 0 --- --mount_check_copy_appdata: ending Load Fpga Success! ECC failed: 0 ECC corrected: 0 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00010000... Erasing 128 Kibyte @ 0 -- 0 % complete Erasing 128 Kibyte @ 20000 -- 50 % complete Erasing 128 Kibyte @ 20000 -- 100 % complete The Help file load OK!! I0101 00:00:10.805797 534 module.cpp:568] --------------------------------------------------------------------------------------- I0101 00:00:10.828555 534 module.cpp:569] Creat Log ----------------------------------------------------------------------------------------------------------------------------------- I0101 00:00:10.858596 534 module.cpp:464] rm -f /usr/bin/siglent/usr/log/Info_19700101-000010.534 I0101 00:00:11.086069 534 module.cpp:489] ----------------------------------------------------------------------------------------------------------------------------------- vxi11_main = 11206 init_lcd_driver()++ g_vinfo.xres = 800 g_vinfo.yres = 480 g_vinfo.bits_per_pixel = 16 E0101 00:00:13.605361 655 dev_interpreter.cpp:332] the device = /dev/sda mount fail I0101 00:00:13.653393 655 dev_interpreter.cpp:338] №ТФШUЕМ /usr/bin/siglent/usr/media/U-disk0 device = /dev/sda1 Erasing 128 Kibyte @ 0 -- 0 % complete Erasing 128 Kibyte @ 20000 -- 50 % complete Erasing 128 Kibyte @ 20000 -- 100 % complete Erasing 128 Kibyte @ 0 -- 0 % complete Erasing 128 Kibyte @ 20000 -- 50 % complete Erasing 128 Kibyte @ 20000 -- 100 % complete FileHeader.product_type == 10000 version_flag == 1 xml_upgrade_id = 10000 Archive: /usr/bin/siglent/usr/usr/upgrade/config.zip inflating: SDS1000_arm.app inflating: sds1000_fpga.rbf inflating: siglentlib.sh inflating: ti81xx.ko inflating: u-boot.img inflating: udc-core.ko inflating: update.sh inflating: upgrade.sh inflating: cfbcopyarea.ko inflating: cfbfillrect.ko inflating: cfbimgblt.ko inflating: da8xx-fb.ko inflating: datafs.img inflating: firmdata0.img inflating: g_usbtmc.ko inflating: gpib.ko inflating: help.bin inflating: libglog.so.0 inflating: MLO inflating: musb_hdrc.ko inflating: NSP_config_upgrade_info.xml inflating: ro_uImage inflating: rw_uImage update.sh starting ... ubi0:rootfs / ubifs ro,relatime 0 0 rootfs ro upgrade /usr/bin/siglent/usr/usr/upgrade/rw_uImage Erasing 128 Kibyte @ 0 -- 0 % complete Erasing 128 Kibyte @ 20000 -- 2 % complete Erasing 128 Kibyte @ 40000 -- 4 % complete Erasing 128 Kibyte @ 60000 -- 6 % complete Erasing 128 Kibyte @ 80000 -- 8 % complete Erasing 128 Kibyte @ a0000 -- 10 % complete Erasing 128 Kibyte @ c0000 -- 12 % complete Erasing 128 Kibyte @ e0000 -- 14 % complete Erasing 128 Kibyte @ 100000 -- 16 % complete Erasing 128 Kibyte @ 120000 -- 18 % complete Erasing 128 Kibyte @ 140000 -- 20 % complete Erasing 128 Kibyte @ 160000 -- 22 % complete Erasing 128 Kibyte @ 180000 -- 25 % complete Erasing 128 Kibyte @ 1a0000 -- 27 % complete Erasing 128 Kibyte @ 1c0000 -- 29 % complete Erasing 128 Kibyte @ 1e0000 -- 31 % complete Erasing 128 Kibyte @ 200000 -- 33 % complete Erasing 128 Kibyte @ 220000 -- 35 % complete Erasing 128 Kibyte @ 240000 -- 37 % complete Erasing 128 Kibyte @ 260000 -- 39 % complete Erasing 128 Kibyte @ 280000 -- 41 % complete Erasing 128 Kibyte @ 2a0000 -- 43 % complete Erasing 128 Kibyte @ 2c0000 -- 45 % complete Erasing 128 Kibyte @ 2e0000 -- 47 % complete Erasing 128 Kibyte @ 300000 -- 50 % complete Erasing 128 Kibyte @ 320000 -- 52 % complete Erasing 128 Kibyte @ 340000 -- 54 % complete Erasing 128 Kibyte @ 360000 -- 56 % complete Erasing 128 Kibyte @ 380000 -- 58 % complete Erasing 128 Kibyte @ 3a0000 -- 60 % complete Erasing 128 Kibyte @ 3c0000 -- 62 % complete Erasing 128 Kibyte @ 3e0000 -- 64 % complete Erasing 128 Kibyte @ 400000 -- 66 % complete Erasing 128 Kibyte @ 420000 -- 68 % complete Erasing 128 Kibyte @ 440000 -- 70 % complete Erasing 128 Kibyte @ 460000 -- 72 % complete Erasing 128 Kibyte @ 480000 -- 75 % complete Erasing 128 Kibyte @ 4a0000 -- 77 % complete Erasing 128 Kibyte @ 4c0000 -- 79 % complete Erasing 128 Kibyte @ 4e0000 -- 81 % complete Erasing 128 Kibyte @ 500000 -- 83 % complete Erasing 128 Kibyte @ 520000 -- 85 % complete Erasing 128 Kibyte @ 540000 -- 87 % complete Erasing 128 Kibyte @ 560000 -- 89 % complete Erasing 128 Kibyte @ 580000 -- 91 % complete Erasing 128 Kibyte @ 5a0000 -- 93 % complete Erasing 128 Kibyte @ 5c0000 -- 95 % complete Erasing 128 Kibyte @ 5e0000 -- 97 % complete Erasing 128 Kibyte @ 5e0000 -- 100 % complete Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000 Writing data to block 3 at offset 0x60000 Writing data to block 4 at offset 0x80000 Writing data to block 5 at offset 0xa0000 Writing data to block 6 at offset 0xc0000 Writing data to block 7 at offset 0xe0000 Writing data to block 8 at offset 0x100000 Writing data to block 9 at offset 0x120000 Writing data to block 10 at offset 0x140000 Writing data to block 11 at offset 0x160000 Writing data to block 12 at offset 0x180000 Writing data to block 13 at offset 0x1a0000 Writing data to block 14 at offset 0x1c0000 Writing data to block 15 at offset 0x1e0000 Writing data to block 16 at offset 0x200000 ++is 3.0 parition version U-Boot SPL 2013.01.01-svn29730 (Mar 27 2017 - 19:02:34) config ddr_pll_config()++ config ddr_pll_config()-- nand_init+++++ nand_init----- Lcd_Init()++ SetUpLCD()++ SetUpLCD()-- len=768052, height=480, width=800 Logo from nandflash: base=0x81000000; end=0x810bb81f; end-base=0xbb81f; rwsize=0xbb820; r=0x0 Lcd_Init()-- U-Boot 2013.01.01-svn29730 (Mar 27 2017 - 19:02:34) I2C: ready DRAM: 128 MiB NAND: 256 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Using default environment set_default_env::7864 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: <ethaddr> not set. Validating first E-fuse MAC cpsw Hit any key to stop autoboot (Re)start USB... USB0: scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Download Linux from USB to Nandflash... reading ro_uImage ** Unable to read file ro_uImage ** reading rootfs.img ** Unable to read file rootfs.img ** reading datafs.img ** Unable to read file datafs.img ** reading logo.bmp ** Unable to read file logo.bmp ** Booting from nand ... NAND read: device 0 offset 0x3080000, size 0x300000 3145728 bytes read: OK ## Booting kernel from Legacy Image at 80200000 ... Image Name: Linux-3.2.0+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2157776 Bytes = 2.1 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. init started: BusyBox v1.13.2 (2012-04-08 17:28:57 CDT) starting pid 520, tty '': '/etc/init.d/rcS' rS in /etc/init.d/rcS: line 15: setterm: not found starting pid 537, tty '/dev/ttyO0': '-/bin/sh' Processing /etc/profile... Done / # check_and_upgrade:starting... mount_fs: rw,sync,ubi1_0,/usr/bin/siglent/usr ubi1_0unattached attach_ubi:datafs attach_ubi:11 UBI device number 1, total 812 LEBs (103104512 bytes, 98.3 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) MOUNT_DIR_NAME = /usr/bin/siglent/usr TEST_RESTURN = is_fs_mounted 0 --- is_need_upgrade is_need_upgrade:need upgrade check_and_upgrade: upgrade start ... upgrade /usr/bin/siglent/usr/usr/upgrade/MLO upgrade /usr/bin/siglent/usr/usr/upgrade/u-boot.img Erasing 128 Kibyte @ 0 -- 0 % complete Erasing 128 Kibyte @ 0 -- 100 % complete Writing data to block 0 at offset 0x0 Erasing 128 Kibyte @ 0 -- 0 % complete Erasing 128 Kibyte @ 0 -- 100 % complete Writing data to block 0 at offset 0x0 Erasing 128 Kibyte @ 0 -- 0 % complete Erasing 128 Kibyte @ 0 -- 100 % complete Writing data to block 0 at offset 0x0 Erasing 128 Kibyte @ 0 -- 0 % complete Erasing 128 Kibyte @ 0 -- 100 % complete Writing data to block 0 at offset 0x0 Erasing 128 Kibyte @ 0 -- 0 % complete Erasing 128 Kibyte @ 20000 -- 6 % complete Erasing 128 Kibyte @ 40000 -- 13 % complete Erasing 128 Kibyte @ 60000 -- 20 % complete Erasing 128 Kibyte @ 80000 -- 26 % complete Erasing 128 Kibyte @ a0000 -- 33 % complete Erasing 128 Kibyte @ c0000 -- 40 % complete Erasing 128 Kibyte @ e0000 -- 46 % complete Erasing 128 Kibyte @ 100000 -- 53 % complete Erasing 128 Kibyte @ 120000 -- 60 % complete Erasing 128 Kibyte @ 140000 -- 66 % complete Erasing 128 Kibyte @ 160000 -- 73 % complete Erasing 128 Kibyte @ 180000 -- 80 % complete Erasing 128 Kibyte @ 1a0000 -- 86 % complete Erasing 128 Kibyte @ 1c0000 -- 93 % complete Erasing 128 Kibyte @ 1c0000 -- 100 % complete Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000 upgrade /usr/bin/siglent/usr/usr/upgrade/ro_uImage Erasing 128 Kibyte @ 0 -- 0 % complete Erasing 128 Kibyte @ 20000 -- 2 % complete Erasing 128 Kibyte @ 40000 -- 4 % complete Erasing 128 Kibyte @ 60000 -- 6 % complete Erasing 128 Kibyte @ 80000 -- 8 % complete Erasing 128 Kibyte @ a0000 -- 10 % complete Erasing 128 Kibyte @ c0000 -- 12 % complete Erasing 128 Kibyte @ e0000 -- 14 % complete Erasing 128 Kibyte @ 100000 -- 16 % complete Erasing 128 Kibyte @ 120000 -- 18 % complete Erasing 128 Kibyte @ 140000 -- 20 % complete Erasing 128 Kibyte @ 160000 -- 22 % complete Erasing 128 Kibyte @ 180000 -- 25 % complete Erasing 128 Kibyte @ 1a0000 -- 27 % complete Erasing 128 Kibyte @ 1c0000 -- 29 % complete Erasing 128 Kibyte @ 1e0000 -- 31 % complete Erasing 128 Kibyte @ 200000 -- 33 % complete Erasing 128 Kibyte @ 220000 -- 35 % complete Erasing 128 Kibyte @ 240000 -- 37 % complete Erasing 128 Kibyte @ 260000 -- 39 % complete Erasing 128 Kibyte @ 280000 -- 41 % complete Erasing 128 Kibyte @ 2a0000 -- 43 % complete Erasing 128 Kibyte @ 2c0000 -- 45 % complete Erasing 128 Kibyte @ 2e0000 -- 47 % complete Erasing 128 Kibyte @ 300000 -- 50 % complete Erasing 128 Kibyte @ 320000 -- 52 % complete Erasing 128 Kibyte @ 340000 -- 54 % complete Erasing 128 Kibyte @ 360000 -- 56 % complete Erasing 128 Kibyte @ 380000 -- 58 % complete Erasing 128 Kibyte @ 3a0000 -- 60 % complete Erasing 128 Kibyte @ 3c0000 -- 62 % complete Erasing 128 Kibyte @ 3e0000 -- 64 % complete Erasing 128 Kibyte @ 400000 -- 66 % complete Erasing 128 Kibyte @ 420000 -- 68 % complete Erasing 128 Kibyte @ 440000 -- 70 % complete Erasing 128 Kibyte @ 460000 -- 72 % complete Erasing 128 Kibyte @ 480000 -- 75 % complete Erasing 128 Kibyte @ 4a0000 -- 77 % complete Erasing 128 Kibyte @ 4c0000 -- 79 % complete Erasing 128 Kibyte @ 4e0000 -- 81 % complete Erasing 128 Kibyte @ 500000 -- 83 % complete Erasing 128 Kibyte @ 520000 -- 85 % complete Erasing 128 Kibyte @ 540000 -- 87 % complete Erasing 128 Kibyte @ 560000 -- 89 % complete Erasing 128 Kibyte @ 580000 -- 91 % complete Erasing 128 Kibyte @ 5a0000 -- 93 % complete Erasing 128 Kibyte @ 5c0000 -- 95 % complete Erasing 128 Kibyte @ 5e0000 -- 97 % complete Erasing 128 Kibyte @ 5e0000 -- 100 % complete Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000 Writing data to block 3 at offset 0x60000 Writing data to block 4 at offset 0x80000 Writing data to block 5 at offset 0xa0000 Writing data to block 6 at offset 0xc0000 Writing data to block 7 at offset 0xe0000 Writing data to block 8 at offset 0x100000 Writing data to block 9 at offset 0x120000 Writing data to block 10 at offset 0x140000 Writing data to block 11 at offset 0x160000 Writing data to block 12 at offset 0x180000 Writing data to block 13 at offset 0x1a0000 Writing data to block 14 at offset 0x1c0000 Writing data to block 15 at offset 0x1e0000 Writing data to block 16 at offset 0x200000 upgrade_app:starting upgrade_app:ending is_no_firmdata0_partition:partion 3.0 check_and_upgrade: upgrade end... rebooting U-Boot SPL 2013.01.01-svn29730 (Mar 27 2017 - 19:02:34) config ddr_pll_config()++ config ddr_pll_config()-- nand_init+++++ nand_init----- Lcd_Init()++ SetUpLCD()++ SetUpLCD()-- len=768052, height=480, width=800 Logo from nandflash: base=0x81000000; end=0x810bb81f; end-base=0xbb81f; rwsize=0xbb820; r=0x0 Lcd_Init()-- U-Boot 2013.01.01-svn29730 (Mar 27 2017 - 19:02:34) I2C: ready DRAM: 128 MiB NAND: 256 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Using default environment set_default_env::7864 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: <ethaddr> not set. Validating first E-fuse MAC cpsw Hit any key to stop autoboot (Re)start USB... USB0: scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Download Linux from USB to Nandflash... reading ro_uImage ** Unable to read file ro_uImage ** reading rootfs.img ** Unable to read file rootfs.img ** reading datafs.img ** Unable to read file datafs.img ** reading logo.bmp ** Unable to read file logo.bmp ** Booting from nand ... NAND read: device 0 offset 0x3080000, size 0x300000 3145728 bytes read: OK ## Booting kernel from Legacy Image at 80200000 ... Image Name: Linux-3.2.0+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2157768 Bytes = 2.1 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. init started: BusyBox v1.13.2 (2012-04-08 17:28:57 CDT) starting pid 519, tty '': '/etc/init.d/rcS' rS in /etc/init.d/rcS: line 15: setterm: not found starting pid 536, tty '/dev/ttyO0': '-/bin/sh' Processing /etc/profile... Done / # check_and_upgrade:starting... mount_fs: rw,sync,ubi1_0,/usr/bin/siglent/usr ubi1_0unattached attach_ubi:datafs attach_ubi:11 UBI device number 1, total 812 LEBs (103104512 bytes, 98.3 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) MOUNT_DIR_NAME = /usr/bin/siglent/usr TEST_RESTURN = is_fs_mounted 0 --- is_need_upgrade is_need_upgrade:not need upgrade check_and_upgrade:end... ++mount_check_copy_appdata: starting mount_fs: ro,sync,ubi2_0,/usr/bin/siglent/firmdata0 ubi2_0unattached attach_ubi:firmdata0 attach_ubi:9 UBI device number 2, total 400 LEBs (50790400 bytes, 48.4 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) MOUNT_DIR_NAME = /usr/bin/siglent/firmdata0 TEST_RESTURN = is_fs_mounted 0 --- --mount_check_copy_appdata: ending Load Fpga Success! ECC failed: 0 ECC corrected: 0 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00010000... Erasing 128 Kibyte @ 0 -- 0 % complete Erasing 128 Kibyte @ 20000 -- 50 % complete Erasing 128 Kibyte @ 20000 -- 100 % complete The Help file load OK!! I0101 00:00:10.685917 534 module.cpp:568] --------------------------------------------------------------------------------------- I0101 00:00:10.711039 534 module.cpp:569] Creat Log ----------------------------------------------------------------------------------------------------------------------------------- I0101 00:00:10.742288 534 module.cpp:464] rm -f /usr/bin/siglent/usr/log/Info_19700101-000010.534 I0101 00:00:10.832217 534 module.cpp:464] rm -f /usr/bin/siglent/usr/log/Warning_19700101-000013.534 I0101 00:00:11.008834 534 module.cpp:489] ----------------------------------------------------------------------------------------------------------------------------------- vxi11_main = 11130 init_lcd_driver()++ g_vinfo.xres = 800 g_vinfo.yres = 480 g_vinfo.bits_per_pixel = 16 I0101 00:00:12.443692 655 dev_interpreter.cpp:220] Udisk = U-disk0 not found notes Could not create log file: File exists COULD NOT CREATE LOGFILE '19700101-000012.534'! E0101 00:00:12.445013 655 dev_interpreter.cpp:395] the u-disk sum = -1 is error E0101 00:00:12.467742 655 dev_interpreter.cpp:406] the device = /usr/bin/siglent/usr/media/U-disk0 umount fail E0101 00:00:12.472785 655 dev_interpreter.cpp:421] not erase the udisk = U-disk0 I0101 00:00:13.544532 655 dev_interpreter.cpp:338] №ТФШUЕМ /usr/bin/siglent/usr/media/U-disk0 device = /dev/sda1 E0101 00:00:13.599209 655 dev_interpreter.cpp:332] the device = /dev/sda mount fail Erasing 128 Kibyte @ 0 -- 0 % complete Erasing 128 Kibyte @ 20000 -- 50 % complete Erasing 128 Kibyte @ 20000 -- 100 % complete Writing data to block 0 at offset 0x0 --- End code --- i am don't know how hide long code,sorry it is after i try update, iwant to copy log but i off it in momrnt :( and my osciloscope is u-boot mode permanently please help me to fix my mistake |
| tautech:
--- Quote from: voronin_10 on October 14, 2020, 07:55:40 pm ---Hi friend, i have bad osciloscome, and my osciloscope is u-boot mode permanently please help me to fix my mistake --- End quote --- Welcome to the forum. I have SDS1000CML+ recovery files. By PM please send me your email and we'll see what we can do to fix it. :) |
| tv84:
Here (without app). |
| voronin_10:
tv84 Thank you, ( P21R2.zip ) this file is very important, tautech Thank you, your file is best, but send this file to this forum, many people seach it i recover my siglent sds1102cml+ with cuted MLO file and original u-boot.img :-BROKE :-/O :-DMM :box: if you device send CC CC CC and uBoot (U-BOOT) dead, this istruction for you step 1) donload teratermpro23 (version 2.3) step 2) connect com to device and run and setup 115200, your device send CC CC word to terminal, step 3) cut in winhex original MLO file start buto to this code 140000EA14F09FE5, and save, your cuted file will start at 140000EA14F09FE5 step 4) terra term File -> Transfer -> XMODEM -> Send open cuted MLO file? program send this file to device step 5) File -> Transfer -> XMODEM -> Send open u-boot.img, program send this file to device, after on console you see word UBOOT# after, recover your device of standarts method this message of about CC CC and recover http://www.mantrid.ru/forum/showthread.php?t=1657 good luck friends by Peter Skip |
| Navigation |
| Message Index |
| Next page |
| Previous page |