Products > Test Equipment

Siglent SDS1000X-HD - Bugs and "features" thread.

<< < (6/10) > >>

2N3055:

--- Quote from: BreakingOhmsLaw on April 07, 2024, 09:55:59 am ---
--- Quote from: 2N3055 on April 06, 2024, 10:53:56 pm ---I'll send you my address for the bottle. I trust you to pick something nice.

--- End quote ---
Please do, I am a man of my word.


--- Quote ---And if your reference for this is Keysight scope make note that their implementation is not correct[...]

--- End quote ---
Indeed. Come to think of it, I don't think I've ever used a non 7-bit I²C part in anger in the past 32 years as an EE. I completely forgot about the extended addressing.

Anyway, a fine bottle of scotch will find it's way to Croatia as soon as it knows where to go. :-+

--- End quote ---

My friend,
I was just joking. There is no need for it, really.
My biggest reward is that I could help. Really, pleasure is all mine.

That does not mean, that if you ever pass through Rijeka, Croatia, let me know, and we can have a sit down a have a proper drink!

As for 10 bit I2C, I never used one either... But I encountered one on some device once. And I was confused that Keysight didn't do it properly. Luckily, my trusty Pico did....

My best,
Siniša

skander36:
@BreakingOhmsLaw I suggest you to revise points #2 and #7.
On #2 clearly is not a bug. Veteran 66has explained why. If we using a Linux share we need to use this format.
On #7 you need to see if this incident can be reproduced. Usually an incident that can't be reproduced can't be called a bug. There were a few others incidents that crash the scope but I can't reproduced anymore. But also on all my scopes I encounter this at a moment in time.(Keysight, RTB2K, Micsig, Rigol).
Did you tried to reset to factory default, Secure erase, before reinstall the firmware?

skander36:
New Firmware for 1000X HD - 1.1.3.8
I did not find 1.1.3.6 even on Chinese site, maybe in new units from factory.

2024/06/14
1.1.3.8
1. Optimize UI, change "on/off" to "On/Off".
2. Solve the problem that some numbers from 200-223 cannot be entered in the first byte of the IP address.
3. Standard software functions of FG and LA.

2024/05/22
1.1.3.6
1. Solve the problem of trigger holdoff fails.
2. Solve the problem of CAN decoding causing crashes with a small probability. 3. Modify the kernel s olve the problem that scpi cannot be
used on a computer with keysight driver installed
4. Solve the problem of advanced trigger (Qualified, Nth
Edge, Delay, Setup/Hold) parameters are not recalled.
5. Solve the problem of delay trigger level setting error.
6. Solve the problem of when the edge is set to Alternating, trigger jitter will occur when entering the other trigger type.
7. Solve some known problems.
8. Optimize waveform capture rate.
9. Optimize self calibration speed.
10. Optimize UI.

Martin72:

--- Quote ---9. Optimize self calibration speed.
--- End quote ---

That would also be something for the SDS3000X HD.
If you start the Self-Cal there, you can confidently go shopping, vacuum the apartment, make dinner... ;)

skander36:

--- Quote from: Martin72 on June 28, 2024, 09:48:23 pm ---
--- Quote ---9. Optimize self calibration speed.
--- End quote ---

That would also be something for the SDS3000X HD.
If you start the Self-Cal there, you can confidently go shopping, vacuum the apartment, make dinner... ;)

--- End quote ---

It's take about 5 minutes now.
Also waveform update does not seem to be faster, but I will keep measure in future.

L.E. In dots mode I have obtained 128 K.

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod