| Products > Test Equipment |
| SIGLENT SDS1102X-C, supported languages issue |
| << < (5/15) > >> |
| tv84:
:-+ Your parsing: --- Code: ---Reversing 1st part of the file [00000000-00000CF7]... XORing with 0xFF (incrementing pattern)... XORing with 0xFF from 0x0000067C until 0x00000CF7 00000000 - Main Checksum: FFFFE632 [00000004-00000CF7] CKSM OK 00000008 - Product_Type: SIGLENT_IE 00000028 - CFG Type: SDS1204CF 0000003C - Manufacturer_Name: SIGLENT 00000047 - CFG Flag_LongMemory: 00 00000048 - Product_ID: 10000 0000004C - Logo Image Size: 00000000 (0 pixels) 00000050 - USB_Prod_ID_PTP: EE39 00000052 - USB_Prod_ID_RAW: EE38 00000054 - USB_Prod_ID_TMC: EE3A 00000056 - USB_Vendor_ID: F4EC 00000058 - Prefix: SDS 0000005C - Logo_Manufacturer: Siglent 0000009C - CFG Flag_pic_machine: 01 0000009D - CFG Flag_sys_machine: 01 0000009E - CFG Flag_____USB_TMC: 01 0000009F - CFG Flag___SCPI/ERES: 00 000000A0 - CFG Fl_invert/neuter: 00 000000A1 - CFG Flag___skew/gate: 01 000000A2 - CFG Flag____vxi/roll: 00 000000A3 - CFG Flag___________A: 00 not_used(?) 000000A4 - CFG Flag___lang_mask: 1FFE 000000A6 - CFG Flag__lang_total: 1 000000A7 - CFG Flag_mach_series: 00 000000A8 - Machine Name 20 MHz: 000000B7 - Machine Name 40 MHz: 000000C6 - Machine Name 60 MHz: 000000D5 - Machine Name 100 MHz: SDS1102X-C 000000E4 - Machine Name 150 MHz: 000000F3 - Machine Name 200 MHz: SDS1202X-C 00000102 - Machine Name 250 MHz: 00000111 - Machine Name 300 MHz: 00000120 - Machine Name 50 MHz: 0000012F - Machine Name 70 MHz: 0000013E - CFG Flag___BW_change: 00 0000013F - CFG Flag_hide_set_BW: 01 00000140 - Machine Name 350 MHz: 0000014F - Machine Name 500 MHz: 0000015E - Machine Name 750 MHz: 0000016D - Machine Name1000 MHz: 0000017C - Machine Name2000 MHz: --- End code --- Let's try and cook some solution. |
| tv84:
What is the answer that you obtain to this SCPI command? MD5_PR? |
| tv84:
I could adjust other things but let's try only the language. Replace you .cfg with this one and report what happened to the language. |
| Othman:
Thanks for your reply I will try replacing the file tomorrow. Now i can not reach my scope |
| Othman:
--- Quote from: tv84 on August 25, 2022, 04:19:06 pm ---What is the answer that you obtain to this SCPI command? MD5_PR? --- End quote --- i have checked this command, i got sds1102X-C as a result. btw i can register this scope to be 200 MHz following the instructions that use key generator based on scope ID and scope serial number. i tried it and it worked and therefore MD5_PR? result in that case was 1202X-C then i returned back the 100 Mhz key. so if this would help for configure the scope model to X-E i can do it. |
| Navigation |
| Message Index |
| Next page |
| Previous page |