Products > Test Equipment

SIGLENT SDS1102X-C, supported languages issue

<< < (5/15) > >>

tv84:
 :-+ Your parsing:


--- Code: ---Reversing 1st part of the file [00000000-00000CF7]...
XORing with 0xFF (incrementing pattern)...
XORing with 0xFF from 0x0000067C until 0x00000CF7

00000000 - Main Checksum: FFFFE632 [00000004-00000CF7]  CKSM OK
00000008 - Product_Type: SIGLENT_IE
00000028 - CFG Type: SDS1204CF
0000003C - Manufacturer_Name: SIGLENT
00000047 - CFG Flag_LongMemory: 00
00000048 - Product_ID: 10000
0000004C - Logo Image Size: 00000000 (0 pixels)
00000050 - USB_Prod_ID_PTP: EE39
00000052 - USB_Prod_ID_RAW: EE38
00000054 - USB_Prod_ID_TMC: EE3A
00000056 - USB_Vendor_ID: F4EC
00000058 - Prefix: SDS
0000005C - Logo_Manufacturer: Siglent
0000009C - CFG Flag_pic_machine: 01
0000009D - CFG Flag_sys_machine: 01
0000009E - CFG Flag_____USB_TMC: 01
0000009F - CFG Flag___SCPI/ERES: 00
000000A0 - CFG Fl_invert/neuter: 00
000000A1 - CFG Flag___skew/gate: 01
000000A2 - CFG Flag____vxi/roll: 00
000000A3 - CFG Flag___________A: 00    not_used(?)
000000A4 - CFG Flag___lang_mask: 1FFE
000000A6 - CFG Flag__lang_total: 1
000000A7 - CFG Flag_mach_series: 00
000000A8 - Machine Name  20 MHz:
000000B7 - Machine Name  40 MHz:
000000C6 - Machine Name  60 MHz:
000000D5 - Machine Name 100 MHz: SDS1102X-C
000000E4 - Machine Name 150 MHz:
000000F3 - Machine Name 200 MHz: SDS1202X-C
00000102 - Machine Name 250 MHz:
00000111 - Machine Name 300 MHz:
00000120 - Machine Name  50 MHz:
0000012F - Machine Name  70 MHz:
0000013E - CFG Flag___BW_change: 00
0000013F - CFG Flag_hide_set_BW: 01
00000140 - Machine Name 350 MHz:
0000014F - Machine Name 500 MHz:
0000015E - Machine Name 750 MHz:
0000016D - Machine Name1000 MHz:
0000017C - Machine Name2000 MHz:

--- End code ---

Let's try and cook some solution.

tv84:
What is the answer that you obtain to this SCPI command?

MD5_PR?

tv84:
I could adjust other things but let's try only the language.

Replace you .cfg with this one and report what happened to the language.

Othman:
Thanks for your reply
I will try replacing the file tomorrow. Now i can not reach my scope

Othman:

--- Quote from: tv84 on August 25, 2022, 04:19:06 pm ---What is the answer that you obtain to this SCPI command?

MD5_PR?

--- End quote ---
i have checked this command, i got sds1102X-C as a result. btw i can register this scope to be 200 MHz following the instructions that use key generator based on scope ID and scope serial number.
i tried it and it worked and therefore MD5_PR? result in that case was 1202X-C  then i returned back the 100 Mhz key. so if this would help for configure the scope model to X-E i can do it.

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod