thnaks tautech for your replyCFG files when run open the instruments OS to accept significant OS changes from firmware like for a significant update or different branding than OEM....or a language change.
so updating the software could not solve this problem? what would you advise me for getting the CFG file, forgive my silly knowledge about this issue.
@tautech,Linux/Telnet noob here too scared to try. :scared:
Search the .cfg file inside your X-E and share it here.
[EDIT 2] the only cfg file seems to be "./usr/bin/siglent/firmdata0/sys_cfg.cfg" on my SDS1204X E . Not sure it will be usefull to the OP :-//
Reversing 1st part of the file [00000000-00000CF7]...
XORing with 0xFF (incrementing pattern)...
XORing with 0xFF from 0x0000067C until 0x00000CF7
00000000 - Main Checksum: FFFFD3E2 [00000004-00000CF7] CKSM OK
00000008 - Product_Type: SIGLENT
00000028 - CFG Type: SDS1004X-E
0000003C - Manufacturer_Name: SIGLENT
00000047 - CFG Flag_LongMemory: 00
00000048 - Product_ID: 10000
0000004C - Logo Image Size: 00000000 (0 pixels)
00000050 - USB_Prod_ID_PTP: EE39
00000052 - USB_Prod_ID_RAW: EE38
00000054 - USB_Prod_ID_TMC: EE3A
00000056 - USB_Vendor_ID: F4EC
00000058 - Prefix: SDS
0000005C - Logo_Manufacturer: Siglent
0000009C - CFG Flag_pic_machine: 01
0000009D - CFG Flag_sys_machine: 01
0000009E - CFG Flag_____USB_TMC: 01
0000009F - CFG Flag___SCPI/ERES: 01
000000A0 - CFG Fl_invert/neuter: 00
000000A1 - CFG Flag___skew/gate: 00
000000A2 - CFG Flag____vxi/roll: 01
000000A3 - CFG Flag___________A: 00 not_used(?)
000000A4 - CFG Flag___lang_mask: 1800
000000A6 - CFG Flag__lang_total: 11
000000A7 - CFG Flag_mach_series: 00
000000A8 - Machine Name 20 MHz: SDS1024X-E
000000B7 - Machine Name 40 MHz: SDS1044X-E
000000C6 - Machine Name 60 MHz: SDS1064X-E
000000D5 - Machine Name 100 MHz: SDS1104X-E
000000E4 - Machine Name 150 MHz: SDS1154X-E
000000F3 - Machine Name 200 MHz: SDS1204X-E
00000102 - Machine Name 250 MHz: SDS1254X-E
00000111 - Machine Name 300 MHz: SDS1304X-E
00000120 - Machine Name 50 MHz: SDS1054X-E
0000012F - Machine Name 70 MHz: SDS1074X-E
0000013E - CFG Flag___BW_change: 00
0000013F - CFG Flag_hide_set_BW: 01
00000140 - Machine Name 350 MHz:
0000014F - Machine Name 500 MHz:
0000015E - Machine Name 750 MHz:
0000016D - Machine Name1000 MHz:
0000017C - Machine Name2000 MHz:
thanks guys for sharingWhich thread ?
let me check and try
i have checked the Uboot os version on my SDS1102X-C. it is 8-1 . do you think the shell scripts on post 345 would work for this os version ?
sorry, noob here. i didn't get it how to do scan port of the host (scope) on my pc. could you please explain more?
thank you
Reversing 1st part of the file [00000000-00000CF7]...
XORing with 0xFF (incrementing pattern)...
XORing with 0xFF from 0x0000067C until 0x00000CF7
00000000 - Main Checksum: FFFFE632 [00000004-00000CF7] CKSM OK
00000008 - Product_Type: SIGLENT_IE
00000028 - CFG Type: SDS1204CF
0000003C - Manufacturer_Name: SIGLENT
00000047 - CFG Flag_LongMemory: 00
00000048 - Product_ID: 10000
0000004C - Logo Image Size: 00000000 (0 pixels)
00000050 - USB_Prod_ID_PTP: EE39
00000052 - USB_Prod_ID_RAW: EE38
00000054 - USB_Prod_ID_TMC: EE3A
00000056 - USB_Vendor_ID: F4EC
00000058 - Prefix: SDS
0000005C - Logo_Manufacturer: Siglent
0000009C - CFG Flag_pic_machine: 01
0000009D - CFG Flag_sys_machine: 01
0000009E - CFG Flag_____USB_TMC: 01
0000009F - CFG Flag___SCPI/ERES: 00
000000A0 - CFG Fl_invert/neuter: 00
000000A1 - CFG Flag___skew/gate: 01
000000A2 - CFG Flag____vxi/roll: 00
000000A3 - CFG Flag___________A: 00 not_used(?)
000000A4 - CFG Flag___lang_mask: 1FFE
000000A6 - CFG Flag__lang_total: 1
000000A7 - CFG Flag_mach_series: 00
000000A8 - Machine Name 20 MHz:
000000B7 - Machine Name 40 MHz:
000000C6 - Machine Name 60 MHz:
000000D5 - Machine Name 100 MHz: SDS1102X-C
000000E4 - Machine Name 150 MHz:
000000F3 - Machine Name 200 MHz: SDS1202X-C
00000102 - Machine Name 250 MHz:
00000111 - Machine Name 300 MHz:
00000120 - Machine Name 50 MHz:
0000012F - Machine Name 70 MHz:
0000013E - CFG Flag___BW_change: 00
0000013F - CFG Flag_hide_set_BW: 01
00000140 - Machine Name 350 MHz:
0000014F - Machine Name 500 MHz:
0000015E - Machine Name 750 MHz:
0000016D - Machine Name1000 MHz:
0000017C - Machine Name2000 MHz:
What is the answer that you obtain to this SCPI command?i have checked this command, i got sds1102X-C as a result. btw i can register this scope to be 200 MHz following the instructions that use key generator based on scope ID and scope serial number.
MD5_PR?
so may we need to do more changes i think. and i'm wondering if this would still work when updating to the newest version 1.3.26
Go to my .cfg file message and replace with the new file that I attached.thnak you for your reply
You can continue to use the script in the USB disk at boot.the script in the USB disk didn't work with me for the last fw version (1.3.26). it seems that with this FW the port 23 is closed while this port is open with the old FW as i notice that when doing port scan.
Or place a call to telnetd in a start script.
last update.
i have updated my scope to newest FW 1.3.26 version. and every think it is ok. i would to thank everybody who was generous and patient advising and helping me especially tv84 who did the important work for reconfiguration the scope.
thank you guys i really appreciate your efforts. and i'm pleased to help any body who might would face the same situation
One note.you might be right. this model may is different. however this thread is not about claiming that we have managed to configure the model X-C to be exactly like X-E model.
Still (afaik) it is not same as SDS1202X-E
One note.you might be right. this model may is different. however this thread is not about claiming that we have managed to configure the model X-C to be exactly like X-E model.
Still (afaik) it is not same as SDS1202X-E
instead of that the main aim for this thread is activating the english language option so this model can support english in UI as the model X-E do.
That was also the reason why I left both .CFG files in my previous post. Anyone can choose between X-C and X-E designations, both with all languages possible.Yes, somehow I think same about 200MHz bandwidth.
Is there a specific X-C firmware release? If there is, maybe the right thing would be to reflash the X-C firmware, now that we have the .CFG "corrected".
And, as rf-loop hints, you could try measure the max BW/performance the device can get. Because, one thing is certain, the 1202X-C designation is in the original .CFG file so this may indicate (for me, at least) that 200MHz is attainable.
Hi, that's awesome stuff. I have the SDS1104X-C and try to get English enabled as well. So far I used the mentioned scripts and telnet to connect to my scope and got the config file. Now my questions are: How do you parse the file and what did you change in order to enable English?
Keep up the great work.
I attached the .cfg file from the Siglent1104X-C.
5- share this file with "TV84" to do the magic job then you will replace the file with the new one that might "TV84" offer you.
i thought the CFG of SDS1202X-C model might be different from the SDS1102X-C. thanks for clarification.
No need to do this step. You just need to overwrite with the appropriate file (attached by me in a previous msg). The .cfg are the same for all scopes in the same situation. Make sure you rename the intended file to "sys_cfg.cfg" before overwriting, and sync.
5- share this file with "TV84" to do the magic job then you will replace the file with the new one that might "TV84" offer you.
No need to do this step. You just need to overwrite with the appropriate file (attached by me in a previous msg). The .cfg are the same for all scopes in the same situation. Make sure you rename the intended file to "sys_cfg.cfg" before overwriting, and sync.
Do you need to overwrite the configuration file by executing commands in telnet? that is, connect to the device via telnet and give a command to replace the file?
or can this be done from a flash drive in the oscilloscope menu?
dear alexkg have you managed to transform your scope? may i can ask you to share here the Acquisition mode menu of your scope, this is a submenu of the acquire menu. i think my scope miss the High Resolution option, can you confirm that with your scope!Correct.
dear alexkg have you managed to transform your scope? may i can ask you to share here the Acquisition mode menu of your scope, this is a submenu of the acquire menu. i think my scope miss the High Resolution option, can you confirm that with your scope!Correct.
To be equivalent to SDS1202X-E it needs the ERES menu.
dear alexkg have you managed to transform your scope? may i can ask you to share here the Acquisition mode menu of your scope, this is a submenu of the acquire menu. i think my scope miss the High Resolution option, can you confirm that with your scope!
dear alexkg have you managed to transform your scope? may i can ask you to share here the Acquisition mode menu of your scope, this is a submenu of the acquire menu. i think my scope miss the High Resolution option, can you confirm that with your scope!Correct.
To be equivalent to SDS1202X-E it needs the ERES menu.
Yeah.
The SDS1202X-C is not the Chinese version of the SDS1202X-E, not at all even it looks outside like it.
It's a bit different. It is also an "web shops only" model series and only for the Chinese domestic market. That model is also clearly slower than the X-E series what is also told in data sheet. Well, when you stretch a penny, you get a stretched penny.
Same for all these models:
SDS1104X-C 100 MHz
SDS1204X-C 200MHz
SDS1102X-C 100 MHz
SDS1202X-C 200MHz
In WFPS which is an indication of system speed.The SDS1202X-C is not the Chinese version of the SDS1202X-E, not at all even it looks outside like it.
It's a bit different. It is also an "web shops only" model series and only for the Chinese domestic market. That model is also clearly slower than the X-E series what is also told in data sheet.
I want to ask you to bring this data here, the difference in technical characteristics. Unfortunately, I did not find a difference in technical characteristics between the X-E and X-C versions. Externally, the devices are one to one, the difference is only in the name of the models :) we will be grateful if you share the information that you found, where it is said that the model for the domestic market is slower than the one that is exported.
dear alexkg have you managed to transform your scope? may i can ask you to share here the Acquisition mode menu of your scope, this is a submenu of the acquire menu. i think my scope miss the High Resolution option, can you confirm that with your scope!Correct.
To be equivalent to SDS1202X-E it needs the ERES menu.
Yeah.
The SDS1202X-C is not the Chinese version of the SDS1202X-E, not at all even it looks outside like it.
It's a bit different. It is also an "web shops only" model series and only for the Chinese domestic market. That model is also clearly slower than the X-E series what is also told in data sheet. Well, when you stretch a penny, you get a stretched penny.
Same for all these models:
SDS1104X-C 100 MHz
SDS1204X-C 200MHz
SDS1102X-C 100 MHz
SDS1202X-C 200MHz
I want to ask you to bring this data here, the difference in technical characteristics. Unfortunately, I did not find a difference in technical characteristics between the X-E and X-C versions. Externally, the devices are one to one, the difference is only in the name of the models :) we will be grateful if you share the information that you found, where it is said that the model for the domestic market is slower than the one that is exported.
Yes but we are talking about 2ch C model not 4ch.
There is already enough confusion with Siglent's alphabet soup of models even in the X-E range and the inconsistency of feature set in this model range/series.
Just compare SDS1202X-E with SDS11/1204X-E then drop in SDS2000X-E....it's a mess whereas they scream for some consistency of features. :scared:
They each have their place but it could be so much better.
****X-C models are just what they are, designed and built to a specific price point.
And all C versions are _only_ for China markets, not for Export. Lets hope Siglent do what they need do before whole mess. Also there is not Stretch penny and you get stretched penny. Outside China here is not any support for these models and must not be.100%
And all C versions are _only_ for China markets, not for Export. Lets hope Siglent do what they need do before whole mess. Also there is not Stretch penny and you get stretched penny. Outside China here is not any support for these models and must not be.100%
Further, Siglent penalties to China exporters are severe as we discovered when reporting a SDS2074X Plus exported to NZ.
Which is very reassuring that Siglent want to protect their worldwide distribution network from their China sellers export of China only models.
Will share some info by private email.And all C versions are _only_ for China markets, not for Export. Lets hope Siglent do what they need do before whole mess. Also there is not Stretch penny and you get stretched penny. Outside China here is not any support for these models and must not be.100%
Further, Siglent penalties to China exporters are severe as we discovered when reporting a SDS2074X Plus exported to NZ.
Which is very reassuring that Siglent want to protect their worldwide distribution network from their China sellers export of China only models.
Siglent is a listed company (Shanghai 688112:SHH) whose purpose is to generate profit for shareholders. It is not an aid organization.
"Siglent wants to protect its global distribution network from Chinese sellers who only export models made in China"
Right!
Everyone wants to protect themselves and their business and this is one extremely important thing in that. We cannot change the fact that China's domestic market is completely different from the foreign market of a Chinese company. They don't work the same way. Therefore, these two "worlds" should not be mixed without harmonized rules of the game.
Of course, when I know China to some extent, I can understand these merchants from some perspective, but understanding and accepting are two different things. Be that as it may, many of them are just supporting their families. But, it should be done in acceptable ways.
Also wfm/s speed is differentin your opinion what is the potential hardware difference between the X-C and X-E model that might lead to this specification difference?
Normal acquisition C model up to 50kwfm/s, Sequence acquisition up to 200kwfm/s
Normal acquisition E model up to 100kwfm/s, Sequence acquisition up to 400kwfm/s
R303Is This a resistor in the pcb ?