Author Topic: Siglent SDS2000X-E  (Read 20753 times)

0 Members and 1 Guest are viewing this topic.

Offline oeweanTopic starter

  • Contributor
  • Posts: 39
  • Country: no
    • Adroit.no
Siglent SDS2000X-E
« on: December 05, 2018, 01:58:18 pm »
Siglent will release the SDS2000X-E on 10th December.
Will come in two flavors, 200MHz and 350MHz...

Norwegian distributor of test and measurement equipment....
Adroit.no
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #1 on: December 06, 2018, 02:52:08 am »
Siglent will release the SDS2000X-E on 10th December.
Will come in two flavors, 200MHz and 350MHz...
Added from later info:
All info is now available:
https://int.siglent.com/products-overview/sds2000x-e/
https://siglentna.com/digital-oscilloscopes/sds2000x-e/
https://www.siglenteu.com/digital-oscilloscopes/sds2000x-e/

--------------------------------------------------------------------

And many of the same features offered in SDS1004X-E.....
Bode plot
MSO option
AWG option
WiFi option

Waveform search
Navigate/History/Sequence
1Mpt FFT
Web browser etc etc

But plus:
2 GSa/s sampling
28 Mpts memory
50 ohm inputs
« Last Edit: September 16, 2019, 09:02:42 am by tautech »
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline tv84

  • Super Contributor
  • ***
  • Posts: 3213
  • Country: pt
Re: Siglent SDS2000X-E
« Reply #2 on: December 06, 2018, 10:50:40 am »
What are the main differences for the 1000X-E?
 

Offline rf-loop

  • Super Contributor
  • ***
  • Posts: 4065
  • Country: fi
  • Born in Finland with DLL21 in hand
Re: Siglent SDS2000X-E
« Reply #3 on: December 06, 2018, 01:16:03 pm »
What are the main differences for the 1000X-E?

You need split thinking to two separate pathway.
SDS1002X-E
SDS1004X-E

Even when SDS2xx2X-E is 2 channel it is not evolution of SDS1002X-E

It is better imagine it is more like half channel SDS1004X-E mutation- evolution (lot of similarities except BW samplerate and due to double samplerate memory is doubled so it is proportionally same.)

It is - imho - not any kind of big jump to up or side. Only more choices for customers  in the current product range at approximately the same level.
 
SDS5000X ... it is totally different case. It's proportionally big step out of the current product portfolio.
« Last Edit: December 06, 2018, 01:18:42 pm by rf-loop »
I drive a LEC (low el. consumption) BEV car. Smoke exhaust pipes - go to museum. In Finland quite all electric power is made using nuclear, wind, solar and water.

Wises must compel the mad barbarians to stop their crimes against humanity. Where have the wises gone?
 

Offline BillB

  • Supporter
  • ****
  • Posts: 615
  • Country: us
Re: Siglent SDS2000X-E
« Reply #4 on: December 06, 2018, 01:50:27 pm »
What are the main differences for the 1000X-E?
It is better imagine it is more like half channel SDS1004X-E mutation- evolution (lot of similarities except BW samplerate and due to double samplerate memory is doubled so it is proportionally same.)

I wonder why this is only offered as a two channel, and not four channel?  How much more popular are the two channel units vs. the four channel ones overall?



 

Offline tv84

  • Super Contributor
  • ***
  • Posts: 3213
  • Country: pt
Re: Siglent SDS2000X-E
« Reply #5 on: December 06, 2018, 02:42:17 pm »
You need split thinking to two separate pathway.
SDS1002X-E
SDS1004X-E

Even when SDS2xx2X-E is 2 channel it is not evolution of SDS1002X-E

So, it's a 1004 with 2 channels, more BW and memory. Other features are the same, so it takes advantage of their maturity (or lack of). I bet it has network security issues, bla, bla, bla...   :D

I don't find it bad. It widens the entry portfolio.

I'm waiting for the SDS5000 but now there are also the Rigols...   :-\
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #6 on: December 06, 2018, 06:29:47 pm »

I don't find it bad. It widens the entry portfolio.

This ^ and at a good price too, a 2ch 200 MHz 2 GSa/s DSO.......under $650 !  :o
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline tv84

  • Super Contributor
  • ***
  • Posts: 3213
  • Country: pt
Re: Siglent SDS2000X-E
« Reply #7 on: December 06, 2018, 07:19:58 pm »
Or 350 MHz...  ::)
 

Offline Performa01

  • Super Contributor
  • ***
  • Posts: 1594
  • Country: at
Re: Siglent SDS2000X-E
« Reply #8 on: December 06, 2018, 10:41:34 pm »
I'm waiting for the SDS5000 but now there are also the Rigols...   :-\
Apart from everything else, I can assure you that a 100MHz square wave looks very different on a true high bandwidth scope from what has been shown in the MSO5000 hacking thread. ;)
 
The following users thanked this post: JPortici, 2N3055

Offline rhb

  • Super Contributor
  • ***
  • Posts: 3476
  • Country: us
Re: Siglent SDS2000X-E
« Reply #9 on: December 07, 2018, 02:53:28 am »
With a 100 MHz square wave there isn't much time for the ringing  from a fast edge to die down. 

IMHO Leo Bodnar's  10 MHz, <40 pS rise time square wave pulser is more appropriate for torturing scopes into confessing.  I've subjected an MSOX3104T and an RTM3104 to it.  The "1 GHz" Keysight had a 436 pS rise time with 7% overshoot.  I sent it back.  An RTM3104 demo unit had a 350 pS rise time and 3% overshoot.  Until I installed the 1.300 FW update.  At which point it had 10% overshoot.  Reverting to 1.100 did not restore the 3% overshoot.  I shall let the reader draw their own conclusions.  I was quite shocked as my experience calibrating a Tek 465 led me to expect no more than 3% overshoot. So I went from delighted to horrified in a week.

I'm very skeptical of the Rigol DS1000E/Z  hacks as I've never seen any step responses.  Logically with a DSO, you build it, then you measure the AFE performance and apply a correction for component tolerances.  After that, if you want software BW updates you apply a 2nd digital filter.  The 1st filter is calibration  for that instrument.  The 2nd filter is a license option.

I recently bought a refurbished 485 on eBay.  I've not yet done the full cal procedure which is *very* long, but I plan to adjust it to under 1% overshoot, rise time be damned.  I don't care if it's only  300 MHz  at -3dB.  I want to be sure that any ringing is the DUT or user error.

My LeCroy DDA-125/LC684DLX has a <250 pS rise time and 20% overshoot. I plan to correct that with sensible anti-alias filters.  750 MHz for 4 channel mode and 1.5 GHz for 2 channel mode.

My Rigol DS1102E is 3% and my Instek MSO-2204EA is 5% both with rise time = 0.35/BW.  And an Instek GDS-2072E hacked to 200 MHz exactly matches the 2204EA both at full BW and at 100 MHz.

There's a long thread about Leo's pulser  here:

https://www.eevblog.com/forum/projects/yet-another-fast-edge-pulse-generator

with lots of screen shots on a wide variety of instruments.  And each unit comes with a printout of the step response on a very high BW scope.  It beats the pants off the Tek 106s  I bought to calibrate my 465 and Dumont 1060.
 
The following users thanked this post: tv84, JPortici

Offline MrW0lf

  • Frequent Contributor
  • **
  • Posts: 922
  • Country: ee
    • lab!fyi
Re: Siglent SDS2000X-E
« Reply #10 on: December 07, 2018, 08:56:17 am »
Just a word of caution for generic reader - if plan to poke actual DUTs with x10 probes then it may make sense to get probe => BNC M & BNC F-F adapter and stick Leo's pulser on the end of probe [possibly with additional 50Ω load], not directly on scope BNC with ext or int 50Ω.
 

Offline Performa01

  • Super Contributor
  • ***
  • Posts: 1594
  • Country: at
Re: Siglent SDS2000X-E
« Reply #11 on: December 07, 2018, 11:56:11 pm »
EDIT: Be aware that this is from a high bandwidth scope and of course not from an SDS2000X-E!

I thought I should back up my claims by showing an example:


Square 100MHz_Z2ns+FFT

This is a 100MHz square wave with <<100ps transition time.

Main timebase is 100ns/div in order to get a sufficiently detailed FFT from DC to 2GHz.
Zoom timebase is 2ns/div in order to get a detailed Y-t view.

Automatic measurements:
FOV = Overshoot after a falling edge.
ROV = Overshoot after a rising edge.
Rise & Fall times are not accurate because of limited scope rise time and also time measurement resolution limited to 20ps at that timebase.
« Last Edit: December 08, 2018, 01:33:36 am by Performa01 »
 

Offline 2N3055

  • Super Contributor
  • ***
  • Posts: 6454
  • Country: hr
Re: Siglent SDS2000X-E
« Reply #12 on: December 08, 2018, 12:40:14 am »
I thought I should back up my claims by showing an example:


Square 100MHz_Z2ns+FFT

This is a 100MHz square wave with <<100ps transition time.

Main timebase is 100ns/div in order to get a sufficiently detailed FFT from DC to 2GHz.
Zoom timebase is 2ns/div in order to get a detailed Y-t view.

Automatic measurements:
FOV = Overshoot after a falling edge.
ROV = Overshoot after a rising edge.
Rise & Fall times are not accurate because of limited scope rise time and also time measurement resolution limited to 20ps at that timebase.

Hello!

That is a nice square. What is the generator if I may ask?

And scope handles it quite well.. Frontend looks very decent here....

Take care!
 

Offline JPortici

  • Super Contributor
  • ***
  • Posts: 3452
  • Country: it
Re: Siglent SDS2000X-E
« Reply #13 on: December 08, 2018, 10:03:01 am »
was that the 5000? nice interface.
Looks like someone actually learned from their masters  ;)
The layout, the font sizes, the proportions, the choice of colours
« Last Edit: December 08, 2018, 10:05:27 am by JPortici »
 

Offline Performa01

  • Super Contributor
  • ***
  • Posts: 1594
  • Country: at
Re: Siglent SDS2000X-E
« Reply #14 on: December 08, 2018, 12:23:08 pm »
Since I don't want to further derail this thread, I've placed a similar post under the associated topic:

https://www.eevblog.com/forum/testgear/at-last-siglent_s-sds5054x-touchscreen/msg2023294/#msg2023294
 
 

Offline oeweanTopic starter

  • Contributor
  • Posts: 39
  • Country: no
    • Adroit.no
Re: Siglent SDS2000X-E
« Reply #15 on: December 09, 2018, 11:48:39 pm »
Tried to upload datasheet for the SDS2000X-E series, but file exceeded file size limit..
If interested you can download it from:
https://www.adroit.no/siglent-sds2202x-e-200mhz-2-kanals-oscilloskop.html#productattach
Norwegian distributor of test and measurement equipment....
Adroit.no
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #16 on: December 10, 2018, 12:04:43 pm »
All info is now available:
http://www.siglent.com/ENs/pdxx.aspx?id=2644&T=2&tid=1
https://www.siglentamerica.com/digital-oscilloscopes/sds2000x-e/
https://www.siglenteu.com/digital-oscilloscopes/sds2000x-e/

SDS2202X-E 200 MHz 2ch USD 619
SDS2352X-E 350 MHz 2ch USD 839

Options
USB AWG
USB WIFI
16ch MSO
« Last Edit: December 10, 2018, 12:24:33 pm by tautech »
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #17 on: December 10, 2018, 12:16:43 pm »
no 4 channel model because?
;D Exactly what I've asked.
You might guess by the front panel layout, one is coming.....
About that, I have zip info.  :(



« Last Edit: December 10, 2018, 12:18:34 pm by tautech »
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline oeweanTopic starter

  • Contributor
  • Posts: 39
  • Country: no
    • Adroit.no
Re: Siglent SDS2000X-E
« Reply #18 on: December 10, 2018, 01:30:54 pm »
Been told there is not going to be a 4 channel.
But who knows, if there is a demand?

Norwegian distributor of test and measurement equipment....
Adroit.no
 

Offline colorado.rob

  • Frequent Contributor
  • **
  • Posts: 419
  • Country: us
Re: Siglent SDS2000X-E
« Reply #19 on: December 10, 2018, 08:59:16 pm »
Are the MSO/LA signals available via LXI/SCPI?  Is serial decode still restricted to just what is on screen?  The 2000X series scope is a bit hobbled by the fact that the logic analyzer (digital signals, serial decoders) is not exposed via SCPI.  And serial decode is limited to just what is on screen.
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #20 on: December 11, 2018, 02:18:37 am »
Are the MSO/LA signals available via LXI/SCPI? 
They are in the current 2kX programming guide:
https://www.siglentamerica.com/wp-content/uploads/dlm_uploads/2017/10/Programming-Guide-1.pdf
P58

Quote
Is serial decode still restricted to just what is on screen?
 
Depends on how you use it.....use the Zoom mode where you can have seconds of data stream on the main window and just a tiny portion in the Zoom window where you can still scroll to any of the packets in the main window.

Quote
The 2000X series scope is a bit hobbled by the fact that the logic analyzer (digital signals, serial decoders) is not exposed via SCPI.
Only Decode as outlined above. Currently none of the Siglent DSO's apparently are able to access Decode via SCPI.
The same applies for Bode plot in the SDS1004X-E models as there is no SCPI command set to enable that.
It will require firmware changes to get  the SCPI command sets installed.
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline blacksheeplogic

  • Frequent Contributor
  • **
  • Posts: 532
  • Country: nz
Re: Siglent SDS2000X-E
« Reply #21 on: December 11, 2018, 03:14:39 am »
All info is now available:
https://www.siglentamerica.com/digital-oscilloscopes/sds2000x-e/

Options
16ch MSO

Maybe I'm missing it and it's in plain sight, but what is the sample rate on the digital channels?
 

Offline colorado.rob

  • Frequent Contributor
  • **
  • Posts: 419
  • Country: us
Re: Siglent SDS2000X-E
« Reply #22 on: December 11, 2018, 03:25:04 am »
Are the MSO/LA signals available via LXI/SCPI? 
They are in the current 2kX programming guide:
https://www.siglentamerica.com/wp-content/uploads/dlm_uploads/2017/10/Programming-Guide-1.pdf
P58
Thanks for sending that.  It has been a while since I looked for an update to the SCPI manual.  I also see that I have missed a couple firmware updates in the past year.

It says "D[X] — Digital channel. Only valid for SDS1000X-E series."  (Page 179, WAVEFORM command.)  Yes, one can control the MSO, but the digital waveforms cannot be retrieved from a 2000X for external analysis.  This means that only the 4 analog waveforms can be used in tools like sigrok -- and, as a 2000X owner, that makes me sad. :(

But that's certainly good news for the 1000X-E users.  And hopefully that means it works on the 2000X-E series as well.
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #23 on: December 11, 2018, 03:28:50 am »
All info is now available:
https://www.siglentamerica.com/digital-oscilloscopes/sds2000x-e/

Options
16ch MSO

Maybe I'm missing it and it's in plain sight, but what is the sample rate on the digital channels?
It's in the datasheet: P3 and 14.
Maximum waveform capture rate up to 1GSa/s, Record length up to 14 Mpts/CH
https://www.siglentamerica.com/wp-content/uploads/2018/12/SDS2000X-E_DataSheet_DS0102E-E01A.pdf

The 16 digital channels are provided with an external module, the same as used for SDS1004X-E models, the SLA1016 that connects into the front Sbus connector.
https://www.siglentamerica.com/accessory/sla1016/

Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #24 on: December 11, 2018, 03:39:41 am »
Are the MSO/LA signals available via LXI/SCPI? 
They are in the current 2kX programming guide:
https://www.siglentamerica.com/wp-content/uploads/dlm_uploads/2017/10/Programming-Guide-1.pdf
P58
Thanks for sending that.  It has been a while since I looked for an update to the SCPI manual.  I also see that I have missed a couple firmware updates in the past year.

It says "D[X] — Digital channel. Only valid for SDS1000X-E series."  (Page 179, WAVEFORM command.)  Yes, one can control the MSO, but the digital waveforms cannot be retrieved from a 2000X for external analysis.  This means that only the 4 analog waveforms can be used in tools like sigrok -- and, as a 2000X owner, that makes me sad. :(

But that's certainly good news for the 1000X-E users.  And hopefully that means it works on the 2000X-E series as well.
Check:
Read Waveform Data of Digital Example
P251
Will that work for you ?
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline colorado.rob

  • Frequent Contributor
  • **
  • Posts: 419
  • Country: us
Re: Siglent SDS2000X-E
« Reply #25 on: December 11, 2018, 04:47:29 am »
Check:
Read Waveform Data of Digital Example
P251
Will that work for you ?

Does that work for you on a 2000X?

For me

    scope.write("d1: wf? dat2")
    data = scope.read_raw()

(reading a digital channel waveform) has no obvious effect on the scope and just hangs the script, whereas

    scope.write("c1: wf? dat2")
    data = scope.read_raw()

(reading an analog channel waveform) works as expected, stopping the scope and returning a chunk of binary data.
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #26 on: December 11, 2018, 04:53:12 am »
Check:
Read Waveform Data of Digital Example
P251
Will that work for you ?

Does that work for you on a 2000X?
Sold mine.  :(
(Replacing with a SDS5kX soon  ;) )

Ok thanks for that info and code, I'll look into it.
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline blacksheeplogic

  • Frequent Contributor
  • **
  • Posts: 532
  • Country: nz
Re: Siglent SDS2000X-E
« Reply #27 on: December 11, 2018, 06:26:55 am »
It's in the datasheet: P3 and 14.
Maximum waveform capture rate up to 1GSa/s, Record length up to 14 Mpts/CH
https://www.siglentamerica.com/wp-content/uploads/2018/12/SDS2000X-E_DataSheet_DS0102E-E01A.pdf

The 16 digital channels are provided with an external module, the same as used for SDS1004X-E models, the SLA1016 that connects into the front Sbus connector.
https://www.siglentamerica.com/accessory/sla1016/

Thanks you. I'm considering something like this as a second MSO.
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #28 on: December 11, 2018, 06:58:45 am »
It's in the datasheet: P3 and 14.
Maximum waveform capture rate up to 1GSa/s, Record length up to 14 Mpts/CH
https://www.siglentamerica.com/wp-content/uploads/2018/12/SDS2000X-E_DataSheet_DS0102E-E01A.pdf

The 16 digital channels are provided with an external module, the same as used for SDS1004X-E models, the SLA1016 that connects into the front Sbus connector.
https://www.siglentamerica.com/accessory/sla1016/

Thanks you. I'm considering something like this as a second MSO.
20 days lead times means I'll have some by early Feb, let me know if you want to demo one.
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline MrW0lf

  • Frequent Contributor
  • **
  • Posts: 922
  • Country: ee
    • lab!fyi
Re: Siglent SDS2000X-E
« Reply #29 on: January 06, 2019, 10:42:54 pm »
Comparing new X-E to my other scopes... 100MHz square from Leo's SMA EXT trigger 40ps pulser. There is SMA => BNC adapter which may degrade fidelity somewhat. No attenuator.

SDS2352X-E 350MHz scope native 50Ω @ 2GSa/s


100MHz scope 50Ω passthru @ 1GSa/s


500MHz scope native 50Ω @ 2.5GSa/s


Might try later with less aggressive signals and supplied probe. If someone has specific request what to test can try. No point to make review as such because it's just as other X-E's only much faster.
« Last Edit: January 06, 2019, 10:45:43 pm by MrW0lf »
 

Offline pascal_sweden

  • Super Contributor
  • ***
  • Posts: 1539
  • Country: no
Re: Siglent SDS2000X-E
« Reply #30 on: January 07, 2019, 12:03:06 am »
Sold mine.  :(
(Replacing with a SDS5kX soon  ;) )

Do you mean DS5k from Rigol, or will there be SDS5kX soon from Siglent?
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #31 on: January 07, 2019, 12:43:15 am »
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline MavMitchell

  • Contributor
  • Posts: 29
  • Country: au
  • Not my real name
Re: Siglent SDS2000X-E
« Reply #32 on: January 07, 2019, 05:03:49 am »
Are you carrying nay Demo Units while you are in WA?
 

Offline Rerouter

  • Super Contributor
  • ***
  • Posts: 4694
  • Country: au
  • Question Everything... Except This Statement
Re: Siglent SDS2000X-E
« Reply #33 on: January 07, 2019, 05:24:07 am »
About lacking decoding over SCPI, It exists in the 1000X-E series, just as normal is undocumented. I suspect they should work for the 2000 series. I have not fully documented most of these yet, but they do exist,

Command    B1:DCCN    B1:DeCo_CAN
Command    B1:DCIC     B1:DeCo_IiC
Command    B1:DCLN    B1:DECO_LIN
Command    B1:DCSP    B1:DECO_SPI
Command    B1:DCUT    B1:DECO_UART
Command    B2:DCCN    B2:DECO_CAN
Command    B2:DCIC    B2:DECO_IIC
Command    B2:DCLN    B2:DECO_LIN
Command    B2:DCSP    B2:DECO_SPI
Command    B2:DCUT    B2:DECO_UART
Query          DCDI         DeCo_DIgital
Command    DCPA         DeCo_Param
Query          DCLR         DeCo_CleaR
Com / Que   DCST         DeCo_STatus
Query          DCVL         DeCo_VaLue

DCVL is the one you want, as best I can see it spits out the decoded stream, I have not yet figured out the formatting yet though,

Try the short commands first, some of the long commands where bugged in the 1000 series, and I expect it to be the same on the 2000
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #34 on: January 07, 2019, 05:36:01 am »
Are you carrying nay Demo Units while you are in WA?
Welcome to the forum.

Nah, sorry on holiday here and soon to catch a bird back to NZ.
Got a couple of units arriving in NZ in a few weeks so I’ll be sure to be posting something about them if they don’t end up presold.
Keep an eye on MrWOlf’s investigations.  :popcorn:
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #35 on: January 24, 2019, 01:33:46 am »
SDS2352X-E -3dB BW check  ~405 MHz   :o

SSG3021X source
N-BNC adapter and Siglent BNC cable.
SDS2kX-E internal 50 ohm termination
Cursors set on p-p @ 200 MHz




---------------------------------------------------------------
SDS2022X-E -3dB BW check = 250 MHz
50 ohm internal termination.
1V p-p @ 200 MHz from HP8654B

« Last Edit: March 27, 2019, 08:08:30 am by tautech »
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #36 on: February 25, 2019, 08:46:29 pm »
Defpom has a look at the 350 MHz SDS2352X-E:

https://youtu.be/7zJ8X51l0Go
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 
The following users thanked this post: TheDefpom

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #37 on: March 27, 2019, 04:54:32 am »
Firmware update for SDS2000X-E models.

Version 1.1.17R6
7.9 MB
https://www.siglentamerica.com/download/8436/

Changelog
1. Fixed the bug: If the oscilloscope is switched off when the CH1 menu is active, it remains without a menu when switching on again.
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #38 on: March 27, 2019, 07:30:59 am »
New SDS2022X-E, unpacked and with the new firmware.

520 MHz from HP sig gen. (substantially attenuated amplitude @ some 300 MHz past rated BW)  :o

Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #39 on: September 13, 2019, 01:38:14 am »
New firmware for SDS2000X-E models.

Version V1.1.19R2
8.3MB
https://int.siglent.com/upload_file/zip/firmware/Oscilloscope/SDS2000X-E_1.1.19R2_EN.zip

Release notes
1. Optimized communication between SDS2000X-E and SLA1016. This revision (and higher) requires the SLA1016
MUST be upgraded to 8.1.16 (or higher) first. Please take a look at ‘Compatibility with SLA1016’ at the end of
the release notes.
2. Optimized Bode Plot: Accuracy and Sensitivity Improvement, New Vari-level Mode for Testing Loop Response, Miscellaneous Function and UI Improvements.
3. Optimized FFT UI: Added Peaks, Markers, and search within FFT.
4. Optimize self-calibration for channels.
5. Optimized accessing USB drive so that when a USB drive is moved to a computer, Windows will not prompt a restoration of the USB drive.
6. Optimize WIFI connection: 63 characters can now be used for a WPA2 PSK key.
7. Added parity options of MARK/SPACE for UART of 9-bit Decode.
8. Optimized behavior of the cursors (x-axis): Added a mode that the cursors remain at the set position on the waveform when changing time base.
9. Added automatic reset to 0 for sample count for statistics after any timebase or voltage range changes.
10. Fixed the bug: The audible beeper activation would affect the voltage waveform displayed for CH2.
11. Fixed the bug of ROV measurement.
12. Fixed the bug: Normal trigger can show more-than-one trigger event on the display at one time.
13. Fixed the bug: Erratic triggering, randomly jumping between the first and the second edge of a signal.
14. Fixed the bug: The acquire time of history is reset to zero if the time reach 1 hour and 11 minutes. The delta time is also wrong if the period is longer than 1 hour and 11 minutes.
15. Fixed The SPI triggering issue: the 16-bit trigger wouldn't work for a gap >360 ns between the two 8-bit packets.
16. Fixed the bug: Save/Recall setup of trigger and scale issue. ( SalesForce ID:P-00199)(SalesForce ID P-00200)
17. Fixed the bug: Reading cursors by SCPI is not accuracy
18. Fixed the bug: In fine adjust mode, some scale such as 302 mV/DIV is in the wrong position.
19. Fixed the bug: LIN decoder doesn't decode frames with zero-length response.
20. Fixed the bug: If the Courser Offset is not a multiple of zoom time base, the cursor will be replaced when zoomed.
21. Fixed the bug: The measurements made with the cursor in Ref. Give wrong values for all the different probes of
X1.
22. Fixed the bug: Measures fairs with GATE give completely random values in signals of low frequency.
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline tv84

  • Super Contributor
  • ***
  • Posts: 3213
  • Country: pt
Re: Siglent SDS2000X-E
« Reply #40 on: September 13, 2019, 10:53:40 am »
 :-+  I see many of the problems identified here in the forums have been included.
 

Offline StasMa

  • Newbie
  • Posts: 4
  • Country: ua
Re: Siglent SDS2000X-E
« Reply #41 on: October 17, 2019, 03:31:08 pm »
yep
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #42 on: July 06, 2020, 07:06:00 am »
New firmware for SDS2000X-E models.

Version: V1.1.19R5
8.3 MB

https://int.siglent.com/upload_file/zip/firmware/Oscilloscope/SDS2000X-E_1.1.19R5_EN.zip

Release notes.
1. Added support for the SAG1021I USB Isolated AWG Module Hardware
2. Fixed the bug: Sometimes PNSU command returns invalid value (Need referring to the latest Program Guide)
3. Added 9 data bits for UART decoding
4. Fixed the bug of UART decoder with some special settings
5. Increased baud rate of UART trigger from 5 Mbps to 20 Mbps
6. Fixed the bug: The command ‘WF? DAT2’returns error length of waveform when digital is enable
7. Fixed the bug: CSV file of waveform has no indication of the trigger point in the data
8. Fixed the bug: After repowering all FFT markers are on just one peak
9. Fixed the bug: After repowering, signal level of CAN trigger can't be recalled
10. Fixed a few SCPI Commands errors:
     MATH: CURSOR_VALUE?
     C3:INVERT_SET? is missing
     HISTORY_LIST? is missing
     DIGITAL:LOW8_SWICHT, typo in name
     C5:COUPLING? typo in name
11. Fixed the Bode Plot bug: Sometime there isn't enough delay after the scope switches timebase values before it tries to take a measurement
12. Fixed the bug: Matlab can’ t import 14 M Matlab waveform files
13. Fixed the bug:‘WF?’ command ignores the length set by ‘WFSU’ for digital
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline rea

  • Contributor
  • Posts: 14
  • Country: af
Re: Siglent SDS2000X-E
« Reply #43 on: June 09, 2021, 06:02:18 am »
There is also firmware version 1.1.20R3 (that my SDS2000X-E came with).  Its being said to be the intermediate version that was created "to optimize the internal processes" (refactoring?) without any (hmm, may be yes, may be not ;) bug fixes/new issues.  And also "... as praparations for the further improvements" was mentioned, so it could be that the new firmware for SDS2000X-E could appear at some point at the Siglent download areas.

Since new devices come with it, I consider it to be stable enough for keen engineers to try it.  It came from Siglent representatives, but just as a lone .ADS file, not the usual zip with changelogs.

http://codelabs.ru/firmware/siglent/sds2000x-e/official/1.1.20R3/
 
The following users thanked this post: tautech, RoV, FrancisM

Offline tv84

  • Super Contributor
  • ***
  • Posts: 3213
  • Country: pt
Re: Siglent SDS2000X-E
« Reply #44 on: June 09, 2021, 08:19:30 am »
http://codelabs.ru/firmware/siglent/sds2000x-e/official/1.1.20R3/

Comparing with SDS2000X-E_1.1.19R2, these are the different files:
Code: [Select]
19/03/2021 13:50:02  82602724  [00156717-005D5F34]  sds1000b.app                                 
19/08/2019 18:08:06  073A3093  [00163D5A-005E1B47]  sds1000b.app                                 
17/08/2018 17:40:11  500FAC1D  [00803DA3-0080BAB9]  top_acq_fpga.bit                             
30/11/2020 09:19:13  7C7B7398  [0080E942-008157E0]  top_acq_fpga.bit                             
12/08/2019 18:47:20  105E9AEF  [00000069-0016158F]  top_sds2000x_e_fpga.bit                     
18/03/2021 09:00:18  0DE50569  [00000069-00153F4C]  top_sds2000x_e_fpga.bit                     
15/08/2019 11:30:21  BCA6A646  [00695A9E-006975EC]  ui_data/arabic_text_info.xml                 
25/11/2020 16:36:12  988957D4  [0068A522-0068C084]  ui_data/arabic_text_info.xml                 
22/07/2019 10:22:28  F80642D3  [00661F53-00665369]  ui_data/english_help_info.xml               
25/11/2020 16:36:13  4188EC72  [00656356-00659735]  ui_data/english_help_info.xml               
15/08/2019 11:30:20  A0CA22D3  [00676BDA-00678742]  ui_data/english_text_info.xml               
25/11/2020 16:36:12  46EF2F58  [0066B604-0066D17E]  ui_data/english_text_info.xml               
15/08/2019 11:30:20  4D4CC7DE  [006C0AD7-006C265E]  ui_data/french_text_info.xml                 
25/11/2020 16:36:11  1938CE93  [006B55A6-006B7145]  ui_data/french_text_info.xml                 
15/08/2019 11:30:20  E913CA3C  [00660398-00661F17]  ui_data/italian_text_info.xml               
25/11/2020 16:36:12  197C678B  [00654785-0065631A]  ui_data/italian_text_info.xml               
15/08/2019 11:30:20  A0CA22D3  [006687F3-0066A35B]  ui_data/japanese_text_info.xml               
25/11/2020 16:36:13  1EC3EBD1  [0065CBBF-0065E73A]  ui_data/japanese_text_info.xml               
15/08/2019 11:30:21  A0CA22D3  [00683B82-006856EA]  ui_data/korean_text_info.xml                 
25/11/2020 16:36:12  820AA2AD  [006785DF-0067A15A]  ui_data/korean_text_info.xml                 
22/07/2019 10:22:28  25C950F8  [0067378D-00676B9E]  ui_data/portuguese_help_info.xml             
25/11/2020 16:36:12  C693D355  [00667B6C-0066B5C8]  ui_data/portuguese_help_info.xml             
15/08/2019 11:30:20  80400B18  [006B4C15-006B679C]  ui_data/portuguese_text_info.xml             
25/11/2020 16:36:11  19001581  [006A96DE-006AB27A]  ui_data/portuguese_text_info.xml             
15/08/2019 14:52:17  BA26AB00  [006AFDEA-006B1CDE]  ui_data/russian_text_info.xml               
25/11/2020 16:36:13  D53886C8  [006A489E-006A67A7]  ui_data/russian_text_info.xml               
22/07/2019 10:22:29  5C36A722  [006AC754-006AFDAE]  ui_data/simp_help_info.xml                   
25/11/2020 16:36:13  CF0A1790  [006A1210-006A4862]  ui_data/simp_help_info.xml                   
15/08/2019 11:30:20  E356D421  [006AAA7F-006AC71B]  ui_data/simp_text_info.xml                   
25/11/2020 16:36:11  9CAEF00B  [0069F51C-006A11D7]  ui_data/simp_text_info.xml                   
15/08/2019 11:30:20  364466B7  [0068D77D-0068F305]  ui_data/spanish_text_info.xml               
25/11/2020 16:36:12  6E9E9F6C  [006821ED-00683D89]  ui_data/spanish_text_info.xml               
22/07/2019 10:22:29  28AB5506  [006B9804-006BCEB9]  ui_data/trad_help_info.xml                   
25/11/2020 16:36:13  CF9CC21D  [006AE2E2-006B1988]  ui_data/trad_help_info.xml                   
12/03/2021 09:51:01  252D17C4  [0068C0BD-0068F33C]  ui_data/trad_menu_info.xml                   
22/07/2019 10:22:28  50B7FBEE  [00697625-0069A89F]  ui_data/trad_menu_info.xml                   
15/08/2019 11:30:21  314D63E0  [0067EBF0-00680905]  ui_data/trad_text_info.xml                   
25/11/2020 16:36:12  4ACF25EA  [0067362C-00675362]  ui_data/trad_text_info.xml                   
16/07/2018 16:54:16  E23B57EF  [007D0479-007D5F3D]  www/BinToCSV_tool.zip                       
24/12/2019 09:26:27  9D21FF8B  [007CB3F5-007D2672]  www/BinToCSV_tool.zip                       
14/07/2018 15:16:18  BDD7A20C  [007597CD-0075A1BF]  www/Instrument/novnc/include/base.css       
29/04/2020 14:25:11  511068CF  [0074E289-0074EC5B]  www/Instrument/novnc/include/base.css       
14/07/2018 15:16:18  0177A851  [007565D8-00756FDA]  www/Instrument/novnc/include/base_mobile.css
29/04/2020 14:25:04  98A0800A  [0074B0B6-0074BA96]  www/Instrument/novnc/include/base_mobile.css
16/12/2019 14:53:28  4928B944  [007960B5-00798A3F]  www/Instrument/novnc/vnc_auto.php           
23/04/2019 16:26:22  F6DAD5CC  [007A1619-007A3C55]  www/Instrument/novnc/vnc_auto.php           
06/12/2019 10:45:29  D4DFFF19  [006B76DE-006B7C0B]  www/SCPI_control.php                         
13/07/2018 10:21:01  F7CB535A  [006C2BE8-006C312E]  www/SCPI_control.php                         
13/07/2018 10:21:01  DA06DD28  [007CEB1A-007CF178]  www/css/device/device_control.css           
29/04/2020 14:24:16  DB820B52  [007C3BE0-007C4228]  www/css/device/device_control.css           
06/12/2019 10:45:27  BF3A0A0E  [007C35EA-007C3B73]  www/css/welcome.css                         
13/07/2018 10:21:01  26D75603  [007CE536-007CEAAD]  www/css/welcome.css                         
06/12/2019 10:45:28  7615EC62  [007D867E-007E6AB0]  www/img/oem_logo.png                         
29/04/2020 14:24:29  BA4681C7  [0079AAE0-0079DD60]  www/js/device/t_table.js                     
31/08/2018 10:44:22  BCC6B03D  [007A5CF6-007A8EC3]  www/js/device/t_table.js                     
13/07/2018 10:21:04  D03B120A  [007B5103-007B53DB]  www/js/home_info.js                         
16/12/2019 14:26:11  C992D686  [007A9FCB-007AA2E9]  www/js/home_info.js                         
16/12/2019 14:53:28  3B557077  [007A4533-007A51F6]  www/js/lan_config.js                         
31/08/2018 10:44:22  85C57E94  [007AF696-007B0327]  www/js/lan_config.js                         
06/12/2019 10:45:28  577E70AE  [007BA347-007BA54E]  www/js/log_in.js                             
13/07/2018 10:21:04  872B6CB6  [007C5439-007C549A]  www/js/log_in.js                             
06/12/2019 10:45:29  1873D146  [007A8E3D-007A9A1C]  www/js/main.js                               
13/07/2018 10:21:04  A11D7515  [007B3F6E-007B4B54]  www/js/main.js                               
06/12/2019 10:45:28  FAE6C4E1  [006B7C35-006B82C0]  www/lan.php                                 
13/07/2018 10:21:03  7F4DEC6B  [006C3158-006C37E2]  www/lan.php                                 
06/12/2019 10:45:28  50415BFD  [007D26A4-007D2FA5]  www/lan_setting.php                         
13/07/2018 10:21:03  CB8B927E  [007D5F6F-007D686B]  www/lan_setting.php                         
04/12/2019 17:22:06  56E1BBCB  [007CA44C-007CB23D]  www/lighttpd.conf                           
06/12/2019 10:45:28  A93CF140  [007C49EC-007C4FC3]  www/login.php                               
31/08/2018 10:44:21  A84261DE  [007CF93C-007CFF09]  www/login.php                               
04/12/2019 17:22:07  02397584  [007C53A5-007CA41C]  www/php.ini                                 
08/04/2020 10:34:20  A99B4633  [006B7195-006B76AB]  www/welcome.php                             
13/07/2018 10:21:01  0C3FC166  [006C26AE-006C2BB5]  www/welcome.php                             
 

Offline rea

  • Contributor
  • Posts: 14
  • Country: af
Re: Siglent SDS2000X-E
« Reply #45 on: June 09, 2021, 03:24:46 pm »
And since it is really boring to live without SHELLCMD, here is the alternative that, I hope, will survive at least some of the future updates of Siglent firmware (and, once currently installed, it will survive all updates up to 1.1.20R3): http://codelabs.ru/firmware/siglent/sds2000x-e/php-cli/v1/
 

Offline RoV

  • Regular Contributor
  • *
  • Posts: 175
  • Country: it
Re: Siglent SDS2000X-E
« Reply #46 on: September 25, 2021, 01:38:32 pm »
There is also firmware version 1.1.20R3 (that my SDS2000X-E came with).  Its being said to be the intermediate version that was created "to optimize the internal processes" (refactoring?) without any (hmm, may be yes, may be not ;) bug fixes/new issues.  And also "... as praparations for the further improvements" was mentioned, so it could be that the new firmware for SDS2000X-E could appear at some point at the Siglent download areas.

Since new devices come with it, I consider it to be stable enough for keen engineers to try it.  It came from Siglent representatives, but just as a lone .ADS file, not the usual zip with changelogs.

http://codelabs.ru/firmware/siglent/sds2000x-e/official/1.1.20R3/

Thank you very much, rea.
The update solved the ugly bug of my post https://www.eevblog.com/forum/testgear/sds2202x-e-fpga-bug-or-broken/msg3518718/#msg3518718.
I wonder why Siglent is taking so long to put an official update on their site.

Offline RoV

  • Regular Contributor
  • *
  • Posts: 175
  • Country: it
Re: Siglent SDS2000X-E
« Reply #47 on: September 25, 2021, 10:34:40 pm »
Successfully applied hack to transform the SDS2202X-E to 2352X-E, thanks to information in the blog!
I can confirm that the hack actually changes both the bandwidth and the rise time, because I measured both configurations, 200 and 350 MHz. The attached reading was obtained with a Marconi 2019A source, with level corrected with an hp power meter. Input to the scope was done using the internal 50 ohm termination:
1282063-0
The final risetime is just below 1 ns, it was 1.2-1.5 ns before the hack. Test was done with a 45 ps rising edge
1282069-1
1282075-2
Also the original 200 MHz probe is better than I thought, reaching well the 350 MHz with a modest attenuation. I tested it using the supplied probe-to-BNC adapter, using a T adapter and an external 50 ohm load. This is a kind of measurement not as reliable as the previous one, so uncertainty is higher.
1282081-3

Offline RoV

  • Regular Contributor
  • *
  • Posts: 175
  • Country: it
Re: Siglent SDS2000X-E
« Reply #48 on: January 09, 2022, 10:40:15 am »
After so many months and in the presence of bugs, the official downloadable FW release for the SDS2202X-E is still stuck at 1.1.19R5, while new models are sold with newer versions. Version 1.1.20R3 was available AT LEAST from last june and thanks to user rea I could install it on last september.
But why don't they distribute updates? Perhaps tautech can help?

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #49 on: January 10, 2022, 08:30:36 am »
After so many months and in the presence of bugs, the official downloadable FW release for the SDS2202X-E is still stuck at 1.1.19R5, while new models are sold with newer versions. Version 1.1.20R3 was available AT LEAST from last june and thanks to user rea I could install it on last september.
But why don't they distribute updates? Perhaps tautech can help?
20R3 is still the current version as I got a copy just recently.
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline RoV

  • Regular Contributor
  • *
  • Posts: 175
  • Country: it
Re: Siglent SDS2000X-E
« Reply #50 on: January 10, 2022, 09:16:55 pm »
20R3 is still the current version as I got a copy just recently.

Thank you for your answer, tautech.
Good to know that 20R3 is still the current version, but why don't they publish it? If they distribute it, it must be tested and official.
 
The following users thanked this post: tautech

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #51 on: January 10, 2022, 11:43:58 pm »
20R3 is still the current version as I got a copy just recently.

Thank you for your answer, tautech.
Good to know that 20R3 is still the current version, but why don't they publish it? If they distribute it, it must be tested and official.
Probably as they're still working on it as I believe R3 was built to fix this issue:
https://www.eevblog.com/forum/testgear/sds2202x-e-calibrate-signal-problems-on-ch1/
It seems a firmware upgrade put the scope out of whack although I have not experienced in any of the firmware installs we often do.
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 

Offline RoV

  • Regular Contributor
  • *
  • Posts: 175
  • Country: it
Re: Siglent SDS2000X-E
« Reply #52 on: January 11, 2022, 10:23:28 pm »
Probably as they're still working on it as I believe R3 was built to fix this issue:
https://www.eevblog.com/forum/testgear/sds2202x-e-calibrate-signal-problems-on-ch1/
It seems a firmware upgrade put the scope out of whack although I have not experienced in any of the firmware installs we often do.
The issue you refer to is quite recent (Jan 2022), while 20R3 was mentioned for the first time by user rea in this message: https://www.eevblog.com/forum/testgear/siglent-sds2000x-e/msg3584977/#msg3584977, so it dates back at least to June 2021. According to rea it was installed by the factory in his new scope, so it was already used in production, but not distributed as a firmware upgrade (and still not today). I can also confirm that it solved the issue https://www.eevblog.com/forum/testgear/sds2202x-e-fpga-bug-or-broken/msg3518718/#msg3518718 that I posted in March 2021.
In the download section of I still see:

Offline FrancisM

  • Contributor
  • Posts: 26
  • Country: fr
Re: Siglent SDS2000X-E
« Reply #53 on: January 13, 2022, 08:52:04 am »
Hi RoV,

I wouldn't worry too much.
I guess that our chinese friends are working hard on a major fw release wich may well surprise us.

I hope you enjoy your "liberated" scope.

All the best,
Francis
 

Offline RoV

  • Regular Contributor
  • *
  • Posts: 175
  • Country: it
Re: Siglent SDS2000X-E
« Reply #54 on: July 18, 2022, 08:59:08 pm »
Successfully applied hack to transform the SDS2202X-E to 2352X-E, thanks to information in the blog!

After PM from one user, I realized that a detailed upgrade procedure wasn't available. So I am attaching a suitable Python 3 script, containing instructions.  :popcorn:
I used only '300' option.

Offline Rapto

  • Newbie
  • Posts: 4
  • Country: pl
Re: Siglent SDS2000X-E
« Reply #55 on: August 25, 2022, 10:43:24 am »
Successfully applied hack to transform the SDS2202X-E to 2352X-E, thanks to information in the blog!

After PM from one user, I realized that a detailed upgrade procedure wasn't available. So I am attaching a suitable Python 3 script, containing instructions.  :popcorn:
I used only '300' option.

Hi, thanks for the script.
So you used the "300M" option to get the upgrade to 2352X-E with 350MHz bandwidth?
If possible, could you check what your scope is displaying as "Product Type" in (press Utility button) > "System Status" menu after applying this patch?
What is the model reported by *IDN? SCPI command?

Thank you!
 

Offline RoV

  • Regular Contributor
  • *
  • Posts: 175
  • Country: it
Re: Siglent SDS2000X-E
« Reply #56 on: August 25, 2022, 09:40:20 pm »
So you used the "300M" option to get the upgrade to 2352X-E with 350MHz bandwidth?
If possible, could you check what your scope is displaying as "Product Type" in (press Utility button) > "System Status" menu after applying this patch?
What is the model reported by *IDN? SCPI command?

Yes, 300M.
See attachments  ;)
 
The following users thanked this post: Rapto

Offline Rapto

  • Newbie
  • Posts: 4
  • Country: pl
Re: Siglent SDS2000X-E
« Reply #57 on: August 26, 2022, 03:27:22 pm »
Thank you, that's very helpful. I made a silly mistake of using the code for "350M"  :palm: and now the scope has a blank field in place of its Product Type. Huh.... I wonder if it's possible to remove a license code...
 

Offline RoV

  • Regular Contributor
  • *
  • Posts: 175
  • Country: it
Re: Siglent SDS2000X-E
« Reply #58 on: August 26, 2022, 07:21:02 pm »
Thank you, that's very helpful. I made a silly mistake of using the code for "350M"  :palm: and now the scope has a blank field in place of its Product Type. Huh.... I wonder if it's possible to remove a license code...

No need, just insert the correct code. Only one remains enabled.
 
The following users thanked this post: Rapto

Offline Rapto

  • Newbie
  • Posts: 4
  • Country: pl
Re: Siglent SDS2000X-E
« Reply #59 on: August 26, 2022, 08:52:21 pm »
Thank you very much!   ^-^
Submitting a new code indeed worked and now my scope also reports SDS2352X-E - the upgrade seems to be successful.
For potential future readers of this thread, my config was:
Software Version: 1.1.19 R5
Uboot-OS version: 2.1
FPGA Version: 2019-08-12
Hardware version: 00-01
 

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #60 on: September 30, 2022, 09:03:31 am »
Spotted an update for these today.....finally the mystical version 20R3 !

https://int.siglent.com/upload_file/zip/firmware/Oscilloscope/SDS2000X-E_V1.1.20R3_EN.zip
8.4MB

The release notes only mention compatibility for later HW versions.
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 
The following users thanked this post: 7thSenpai

Offline MPX

  • Newbie
  • Posts: 2
  • Country: nl
Re: Siglent SDS2000X-E
« Reply #61 on: October 01, 2022, 11:48:39 am »
2202>2352

Software Version 1.1.20R3
UBoot-OS Version 2.1
FPGA Version 2021-03-17
Hardware Version 08-01

 

Offline RoV

  • Regular Contributor
  • *
  • Posts: 175
  • Country: it
Re: Siglent SDS2000X-E
« Reply #62 on: October 01, 2022, 08:03:58 pm »
Spotted an update for these today.....finally the mystical version 20R3 !

https://int.siglent.com/upload_file/zip/firmware/Oscilloscope/SDS2000X-E_V1.1.20R3_EN.zip
8.4MB

The release notes only mention compatibility for later HW versions.

I saw it a couple weeks ago. Downloaded, it is binary identical to the unofficial 20R3 found one year ago thanks to user rea here on eevblog.
Not really HW compatibility only: it has several improvements respect to 19R5. In particular, it solved a problem I had (see my post of sep 25 in this thread).
 
The following users thanked this post: tautech

Offline tautech

  • Super Contributor
  • ***
  • Posts: 28147
  • Country: nz
  • Taupaki Technologies Ltd. Siglent Distributor NZ.
    • Taupaki Technologies Ltd.
Re: Siglent SDS2000X-E
« Reply #63 on: February 28, 2024, 09:54:28 am »
New firmware for SDS2000X-E models

Version: V1.1.20R6
7.5 MB
https://int.siglent.com/upload_file/zip/firmware/Oscilloscope/SDS2000X-E_V1.1.20R6_EN_.zip

Release notes
Fixed the bug: The average of measurement is mistake for 35M points
Optimized the time of auto-setup
Avid Rabid Hobbyist
Siglent Youtube channel: https://www.youtube.com/@SiglentVideo/videos
 


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf