Products > Test Equipment

Siglent Technologies SDS1202X-E - FREQ MEASUREMENT CAPABILITIES....

<< < (2/2)

Hank69:
Thank to my repliers  ;-)
My projects are not complex circuits, just control and command of various "retirement projects" around the house and a few that are not in the "operate fast mode", but, with circuits operating in the sub 10 Hz range.  ME/WE may think ME/WE may need more scope than ME/WE think ME/WE may need....  I'LL STOP NOW   :scared:.... My Hantek DSO2D15 will, in reality, perform all I REALLY need to do.... (AND, it can measure 7.38 Hz very well)....

Roger Need:

--- Quote from: tautech on February 16, 2023, 08:01:43 am ---Typically 10 Hz is as low as you can go however for the 4ch version the recently added Counter allows for lower frequencies and the other rule of thumb is to have a full period displayed rather than just a part of one.
Frequency measure and HW counter start displaying instability below 10 Hz.
HW counter results are dependant on trigger levels and this can be used to advantage at times.

Some SDS1104X-E screenshots attached FYI showing simple measure, Statistics, Counter and at top right the HW counter.
Signal source SDG6022X

--- End quote ---

Tautech,

As a distributor you have contacts at the Siglent factory.  Have you heard if they will be updating the 1202X-E to have the FFT marker plotting and counter features of the 1104x-E?

Roger

tautech:

--- Quote from: Roger Need on February 17, 2023, 12:22:14 am ---
--- Quote from: tautech on February 16, 2023, 08:01:43 am ---Typically 10 Hz is as low as you can go however for the 4ch version the recently added Counter allows for lower frequencies and the other rule of thumb is to have a full period displayed rather than just a part of one.
Frequency measure and HW counter start displaying instability below 10 Hz.
HW counter results are dependant on trigger levels and this can be used to advantage at times.

Some SDS1104X-E screenshots attached FYI showing simple measure, Statistics, Counter and at top right the HW counter.
Signal source SDG6022X

--- End quote ---

Tautech,

As a distributor you have contacts at the Siglent factory.  Have you heard if they will be updating the 1202X-E to have the FFT marker plotting and counter features of the 1104x-E?

Roger

--- End quote ---
TBH I doubt they ever will.  :(
Plenty of time has gone by that several features from 4ch X-E may have been added but zip has been done.
There are more features in the 2ch SDS2202X-E but it costs more than the 4ch SDS1104X-E and still lacks some features those good little scopes have.

But later this year we will have further choices but sorry at this time can't disclose.  :-X

BillyO:
I maybe seeing things but I think I see the writing on the wall for end to 2ch scopes.

Hank69:
During the process to choose a scope that WILL read/measure a sub 10 Hz signal, I did discover during my "Scope go round" testing that the SDS1202X-E DOES measure these signals.  The attached pix shows that even though the top right "freq box" only displays an "f< 10Hz",  in the measurement option screen there is a bevy of options of which to choose that will display the data at the bottom info bar and is also measured with a cursor measurement - see pix....  The Hantek DSO2D15 which I also tested, did a very good job with these low frequencies, but, for just a "few" dollars more, the features and quality of operation of this Siglent model will be my scope of choice....

Navigation

[0] Message Index

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod