Products > Test Equipment

Sniffing the Rigol's internal I2C bus

<< < (361/899) > >>

cybernet:

--- Quote from: alank2 on December 09, 2013, 10:49:18 pm ---So are you loading these codes with 00.01.01.00.02 and then upgrading to 00.02.01.00.03 to utilize them?

--- End quote ---

no, i just upgraded to the new fw, and applied them.

alank2:

--- Quote from: cybernet on December 09, 2013, 10:50:31 pm ---no, i just upgraded to the new fw, and applied them.

--- End quote ---

With a diagnostic key or generated key?  Did you find the new point and crack the new algo?  Does the 00.02.01.00.03 firmware detect a Non-A model and accept normal keys?

AndersAnd:

--- Quote from: cybernet on December 09, 2013, 10:34:15 pm ---for FW 00.02.01.00.03 - on a DS2000 (NON A version only !)


--- Code: ---0x1C080    - DSEA - PROTOCOL ANALYSIS - CAN
0x1C040    - DSCA - BANDWIDTH - 300M Bandwidth (takes a reboot to show up in System Info)
0x1C020    - DSBA - (installs option, but i dont see it ?)
0x1C010    - DSAS - BANDWIDTH - 200M Bandwidth
<known codes still work - see elsewhere>

enable 0x1C0E7 -> all but 100/200M bandwidth-> DSHH
--- End code ---

--- End quote ---
Awesome :-+ DSAS also works with older SW versions according to http://riglol.3owl.com

--- Quote ---DS2000 device options:
first character: D = official, V = trial
DSAB - Advanced Triggers
DSAC - Decoders
DSAE - 56M Memory
DSAJ - 100MHz
DSAS - 200MHz
DSAZ - all options
--- End quote ---


--- Quote from: cybernet on December 09, 2013, 10:34:15 pm ---i wonder if 0x1C020 is the 50Ohm option, which my hw probably doesnt support.
--- End quote ---
Can't you tell a difference in the menu if the 50 Ohm option is enabled by a key or not, even if th HW doesn't support it in HW 1 doesn't support it?

AndersAnd:

--- Quote from: alank2 on December 09, 2013, 10:52:09 pm ---
--- Quote from: cybernet on December 09, 2013, 10:50:31 pm ---no, i just upgraded to the new fw, and applied them.

--- End quote ---
With a diagnostic key or generated key?  Did you find the new point and crack the new algo?  Does the 00.02.01.00.03 firmware detect a Non-A model and accept normal keys?

--- End quote ---
I beleive you can still use this keygen http://riglol.3owl.com and then just type DSAR DSHH instead of the usual DSAZ to enable all options on the new FW 00.02.01.00.03 for non-A DS2000, including CAN protocol analysis, 300 MHz BW (and maybe 50 ohm input option?).

iNoxxam:
Hello,
I have a DS2072 hardware 1 and can't do the update to http://www.filedropper.com/ds2302rilol and therefore no CAN.
The update procedures seems to run like it should, and then, when the scope reboots, everything is just like before. The software version did not move from 01.01.00.00.02.
I have a DS2A0000000001 serial, could that be an issue?

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod