| Products > Test Equipment |
| Sniffing the Rigol's internal I2C bus |
| << < (382/899) > >> |
| ted572:
[quote from marmad « Reply #1936 on: Today at 07:40:13 AM » from: ted572 on Today at 07:33:45 AM DS2000/DS2302 with updated FW 02.01.00.03 falls back to DS2202: My DS2072 with upgrade DS2302 falls back to DS2202 with max TB of 2 ns when I update FW from 01.01.00.02it to FW 02.01.00.03 per ’cybernet' using the Boot Method (Power ON + Help) as he recommends and describes for updating to this FW. BTW the S/N is still the original. . . . . . . . . . from marmad: There's no reason for using cybernet's modified FW to achieve 300MHz bandwidth anymore - it's a purchasable and installable option in the newest firmware (as is the CAN trigger/decode). Just look back through the last couple of pages for the keys needed to install either or both options in v.2 firmware. ---------------------------------------------------------------------------------------------------------------------------------------------------------- and [Quote from AndersAnd « Reply #1937 on: Today at 07:41:52 AM » Ted, you need to use DSHH when generating an all options enabled key for the new firmware instead of DSAZ used on older firmwares. So before upgrading to the new firmware I would uninstall all keys, then upgade to the new firmware and generate a new key using DSHH. Don't use any custom firmware to get 300 MHz anymore, you can get that with DSHH. ----------------------------------------------------------------------------------------------------------------------------------------- Fantastic ! Thank you both so much. I don't know how I missed all of this, as I thought that I read everything here. I didn't have a clue about this. And it was so easy. Thanks again, Ted |
| creyc:
--- Quote from: AndersAnd on November 04, 2013, 09:53:08 pm --- I notice the 500µV option for DS1000z has a different 3rd letter than the other options too. Is this a mistake too or is it supposed to be this way? Can't recall if there's a code table for DS1000z earlier in this topic similar to the on above for DS4000? I think I've missed it if there is. --- Quote ---DS1000z device options: DSAB - Advanced Triggers DSAC - Decoders DSAE - 24M Memory DSAJ - Recorder DSBA - 500uV Vertical --- End quote --- --- End quote --- Speaking of this 500µV option for the DS1000Z, it doesn't show up in the installed options menu before or after entering. Additionally, is there a code to remove this option? |
| m-joy:
Hello, i just bought the DS2072 with 70Mhz. Now i want to have all the cool stuff including maximum bandwidth. I downloaded the Rigon KeyGen v2.0b1. I am always reading of an DSHH option, but my keygen has only DSAH DSAR and DSAZ. So whats the best way to get this working? Can i easy remove this stuff wo waranty? Greetings |
| AndersAnd:
--- Quote from: m-joy on December 12, 2013, 08:47:36 am ---Hello, i just bought the DS2072 with 70Mhz. Now i want to have all the cool stuff including maximum bandwidth. I downloaded the Rigon KeyGen v2.0b1. I am always reading of an DSHH option, but my keygen has only DSAH DSAR and DSAZ. So whats the best way to get this working? Can i easy remove this stuff wo waranty? Greetings --- End quote --- Use this keygen http://riglol.3owl.com and just type DSHH even though it's not listed as an option. Leave the Privatekey box empty, it will fill out this itself. |
| m-joy:
--- Quote from: AndersAnd on December 12, 2013, 08:50:19 am --- --- Quote from: m-joy on December 12, 2013, 08:47:36 am ---Hello, i just bought the DS2072 with 70Mhz. Now i want to have all the cool stuff including maximum bandwidth. I downloaded the Rigon KeyGen v2.0b1. I am always reading of an DSHH option, but my keygen has only DSAH DSAR and DSAZ. So whats the best way to get this working? Can i easy remove this stuff wo waranty? Greetings --- End quote --- Use this keygen http://riglol.3owl.com and just type DSHH even though it's not listed as an option. Leave the Privatekey box empty, it will fill out this itself. --- End quote --- Great! Going to try that ;) so do i get 300Mhz or 200Mhz? I am a lil bit confused right now ;) Will that work on the latest firmware? Should i update to further FW in the future? Greets |
| Navigation |
| Message Index |
| Next page |
| Previous page |