Products > Test Equipment

Sniffing the Rigol's internal I2C bus

<< < (382/899) > >>

ted572:
[quote from marmad « Reply #1936 on: Today at 07:40:13 AM »

    from: ted572 on Today at 07:33:45 AM    DS2000/DS2302 with updated  FW 02.01.00.03 falls back to DS2202:

        My DS2072 with upgrade DS2302 falls back to DS2202 with max TB of 2 ns when I update FW from 01.01.00.02it to FW 02.01.00.03 per ’cybernet' using the Boot Method (Power ON + Help) as he recommends and describes for updating to this FW.  BTW the S/N is still the original. . . . . . . . . .     

from marmad:  There's no reason for using cybernet's modified FW to achieve 300MHz bandwidth anymore - it's a purchasable and installable option in the newest firmware (as is the CAN trigger/decode). Just look back through the last couple of pages for the keys needed to install either or both options in v.2 firmware.
----------------------------------------------------------------------------------------------------------------------------------------------------------
and

 [Quote from AndersAnd « Reply #1937 on: Today at 07:41:52 AM »
 
Ted, you need to use DSHH when generating an all options enabled key for the new firmware instead of DSAZ used on older firmwares.
So before upgrading to the new firmware I would uninstall all keys, then upgade to the new firmware and generate a new key using DSHH.
Don't use any custom firmware to get 300 MHz anymore, you can get that with DSHH.
-----------------------------------------------------------------------------------------------------------------------------------------

Fantastic !   Thank you both so much.  I don't know how I missed all of this, as I thought that I read everything here.  I didn't have a clue about this.  And it was so easy.  Thanks again, Ted

creyc:

--- Quote from: AndersAnd on November 04, 2013, 09:53:08 pm ---
I notice the 500µV option for DS1000z has a different 3rd letter than the other options too.
Is this a mistake too or is it supposed to be this way?
Can't recall if there's a code table for DS1000z earlier in this topic similar to the on above for DS4000? I think I've missed it if there is.


--- Quote ---DS1000z device options:
DSAB - Advanced Triggers
DSAC - Decoders
DSAE - 24M Memory
DSAJ - Recorder
DSBA - 500uV Vertical
--- End quote ---

--- End quote ---

Speaking of this 500µV option for the DS1000Z, it doesn't show up in the installed options menu before or after entering.  Additionally, is there a code to remove this option?

m-joy:
Hello,
i just bought the DS2072 with 70Mhz. Now i want to have all the cool stuff including maximum bandwidth.
I downloaded the Rigon KeyGen v2.0b1.
I am always reading of an DSHH option, but my keygen has only DSAH  DSAR and DSAZ.
So whats the best way to get this working? Can i easy remove this stuff wo waranty?

Greetings

AndersAnd:

--- Quote from: m-joy on December 12, 2013, 08:47:36 am ---Hello,
i just bought the DS2072 with 70Mhz. Now i want to have all the cool stuff including maximum bandwidth.
I downloaded the Rigon KeyGen v2.0b1.
I am always reading of an DSHH option, but my keygen has only DSAH  DSAR and DSAZ.
So whats the best way to get this working? Can i easy remove this stuff wo waranty?

Greetings

--- End quote ---
Use this keygen http://riglol.3owl.com and just type DSHH even though it's not listed as an option. Leave the Privatekey box empty, it will fill out this itself.

m-joy:

--- Quote from: AndersAnd on December 12, 2013, 08:50:19 am ---
--- Quote from: m-joy on December 12, 2013, 08:47:36 am ---Hello,
i just bought the DS2072 with 70Mhz. Now i want to have all the cool stuff including maximum bandwidth.
I downloaded the Rigon KeyGen v2.0b1.
I am always reading of an DSHH option, but my keygen has only DSAH  DSAR and DSAZ.
So whats the best way to get this working? Can i easy remove this stuff wo waranty?

Greetings

--- End quote ---
Use this keygen http://riglol.3owl.com and just type DSHH even though it's not listed as an option. Leave the Privatekey box empty, it will fill out this itself.

--- End quote ---

Great!
Going to try that ;) so do i get 300Mhz or 200Mhz? I am a lil bit confused right now ;)
Will that work on the latest firmware? Should i update to further FW in the future?

Greets

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod