Products > Test Equipment
Sniffing the Rigol's internal I2C bus
<< < (391/899) > >>
Pinkus:
Just FYI if you have an older HW 1.0 DS2072 and if you are wondering if it works there.
I did upgrade my HW 1.0 DS2072 without any problems (was of course at 200 Mhz etc. before): I did uninstall all options first (SCPI command), then rebooted with pressed F6, then rebooted again with inserted USB stick with latest FW.
After the upgrade I pressed F6 again during the reboot.
Then I entered the new license number generated with DSHH key:
VoilĂ : 300 Mhz and all options including CAN available and working.

Thank you all!

EV:
Yes, it works now, Thanks!  :)
UberSteve:

--- Quote from: Pinkus on December 13, 2013, 09:55:51 pm ---Just FYI if you have an older HW 1.0 DS2072 and if you are wondering if it works there.
I did upgrade my HW 1.0 DS2072 without any problems (was of course at 200 Mhz etc. before): I did uninstall all options first (SCPI command), then rebooted with pressed F6, then rebooted again with inserted USB stick with latest FW.
After the upgrade I pressed F6 again during the reboot.
Then I entered the new license number generated with DSHH key:
VoilĂ : 300 Mhz and all options including CAN available and working.

Thank you all!

--- End quote ---

Just to add another data point, I went through the exact same scenario and now have 300Mhz with all options (inc. CAN), enabled. (serial number still intact also).

EV:
Ok, I installed also BW 300M option to my DS2202. Rise time tests are here:

https://www.eevblog.com/forum/testgear/first-impressions-and-review-of-the-rigol-ds2072-ds2000-series-dso/1860/
jkw13:

--- Quote from: Avotronics on November 26, 2013, 05:56:14 pm ---Can I get clarification; Are these all the models that these instructions cover?


DP832
DS1000z
DS2000
DS4000
DSA815

Read this topic, you will probably learn a lot and avoid some mistakes in the updating process. And maybe even be able to help other members out with questions or further hacking. Lazy people will skip this step.
Make sure your have updated your Rigol to the latest firmware version before entering any keys. Except for DP832 where Rigol has changed the keys in 01.08.00, so install firmware 01.06.00 before entering any keys. Then you can upgrade the firmware to 01.08.00 afterwards. Read here.
Go to studio25's RigLOL website: http://riglol.3owl.com or Avotronics's mirror site: http://rigol.avotronics.co.uk/riglol
Enter the Rigol serial number in the "Serial:" box.
Find the correct 4 letter code for your desired option in the tables at the above website (e.g. DSAZ to enable all options on DS2000 series scopes).
Enter this 4 letter code in the "Options:" box.
Don't enter anything into the "Privatekey:" box, but just hit generate and it will fill out the box automatically and then generate a valid license key in a pop-up window.
Enter this license key in the right menu on your Rigol (check your manual) and hit Apply.
Reboot, verify options installed and enjoy!

--- End quote ---

I think I've "bricked" my new DP832 by downgrading it to v1.06 and back to v1.08.
ADC cal doesn't work anymore, and the display meters are wrong.
Is there any way to recover from this do you think? Perhaps I did something wrong?
Does anyone know the ManualCal procedure?   :-BROKE
Thanks!
Navigation
Message Index
Next page
Previous page
There was an error while thanking
Thanking...

Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod