Products > Test Equipment

Sniffing the Rigol's internal I2C bus

<< < (411/899) > >>

marmad:

--- Quote from: tirulerbach on December 19, 2013, 06:32:24 pm ---However, it would be nice, if a non-A-owner will remove his keys and try this procedure with the newest firmware (which is for both scopes, "a" and "non-a") to check if it still works.

--- End quote ---

BTW, there's a good chance that it still works - since it was never published before - and the A-models still use trial minutes. It's clearly part of some procedure that Rigol does at the factory to initiate the DSO (setting the clock for the first time, calibrating, initiating trial minutes, etc) which they never thought any owners would stumble upon. We only found it because the early firmware had a bug which reset trial minutes on a self-calibration - and so we thought we might also use it to restart the trial.

But no reason to try until your minutes run out - and hopefully a keygen will come soon anyway.

Pehtoori:
Hi everyone! Just read the whole thread, what a journey, my head is bit sore. Not my native language and have dyslexia so took 2 days straight, ok to be honest skipped German parts :D

Planning to buy Rigol DS2072A, but maybe waiting for the hack before ordering or if no one can get that JTAG dumbed try to step in. Would be my first with JTAG so don't hold your breath.

Maybe we should put fundraising to buy one and send it to (cybernet?). 20€/25$ each would take around 40 to donate. After it gets hacked sell it in ebay and funds goes to next target. Or to hacker, but that may make him legal target as hi is profiting from the activity.

MrsR:
Hi! guys,
Well I have had no luck in updating my DS2072 to a DS 2202.
I have tried 3 FW versions. 1.0.05, 1.0.03 and 2.001.0.03 ( NOT WRITTEN PROPERLY ) but I am sure you's will know what versions I am talking about.

 ON REFLECTION :-//

A)- Has anyone done the upgrades with a RIGOL official upgrade loaded.( mine is the larger memory )

B)- I noticed that the official key has 21 numbers and the NOT official key is 16.

C)- The NOT official generated upgrade is 4 groups of 7 letter/numbers the first two 7 letter/number groups are the same for all the upgrades.

D)- The official 4- 7 letter/number groups for the memory upgrade are completely different to the official ones.

E)- I have been wondering if I used the Key number on the RIGOL upgrade site would it generate the 4-7 letter/number group.

Anyone have any suggestions what to try next.    HELP!!!!! |O

AndersAnd:
@MrsR

Have you tried to uninstall all keys before installing a new one?
What 4 letter option did you use to generate your key?
Did you type in the correct serial number?
What key generator did you use? This one? http://riglol.3owl.com/
Can you post your generated key?

It's easier to help if you post the exact procedure you used.



--- Quote from: MrsR on December 20, 2013, 12:00:05 am ---B)- I noticed that the official key has 21 numbers and the NOT official key is 16.
--- End quote ---
What do you mean by 16 and 21 numbers? The keys consists of 28 alphanumeric values.

marmad:

--- Quote from: MrsR on December 20, 2013, 12:00:05 am ---A)- Has anyone done the upgrades with a RIGOL official upgrade loaded.( mine is the larger memory )

--- End quote ---

@MrsR: Yes. Upgraded to the new v.2 firmware with my official key for all options already installed - no problem. I used my serial number and the code DSEA in the Riglol key generator to generate a CAN license key. Installed with no problem. A couple of days later I did the same again using DSCA for the 300MHz option to measure waveform update rates at 1ns/div- again installed with no problem.

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod