Products > Test Equipment
Sniffing the Rigol's internal I2C bus
<< < (536/899) > >>
AndersAnd:

--- Quote from: pillex on January 20, 2014, 11:05:02 pm ---From the posts begging from page 164 I understood that "tirulerbach" is the man to send the memory dump.
--- End quote ---
Just upload it to a file hosting site and link to the file in the forum so everyone working on it can have a look.
Several members has uploaded to https://mega.co.nz and posted the lniks in this topic.
Git:


--- Quote from: NikWing on January 13, 2014, 09:20:30 pm ---that's the 2 digits after the ds2d15, right?
then I also have one from week 46

--- End quote ---

Is it possible they are algorithmically generating ECC keys etc from digits 7 & 8 of the serial number if that is week number?

Git
cidcorp:

Well after receiving my DS1074Z-S (I a DS2102, but really need the extra 2 channels) I decided to try as is out of the box using the riglol keys generated.
Everything installed without a problem - all option installed.  I didn't reread the thread so I missed the little detail about the 500uV Vert unlock not working.
Sooo I installed the DSFR instead of the DSER (which I believe is everything except the 500uV)... if someone can confirm.

I will be doing the uninstall and reinstall with DSER to clear up a trace off set problem (goes to top of display and can't be brought down) when on the lowest vertical setting.

BTW this little guy is sooo cute.  Like a mini-me of the 4000 or 2000 scopes lol.

[1] Two questions though relating to the DS1000Z's - is there an EXTENDED system/info button trick like the DS2000 ie F7-F6-F7-etc (sorry going from memory which is horrible) for
HW revision FW revision info?
[2] Am I missing something or are both Left and Right menus permanently on screen???
granz:

--- Quote from: zombie28 on January 19, 2014, 11:08:34 am ---
AFAIK HW version '2.0' is not Rigol's term, it's just used on this forum to describe new version of DS2k(A) PCB. The newest HW version displayed by DS2kA scopes I've seen so far is 1.0.2.0.2 and it doesn't change after firmware upgrade (take a look at Flipp's screenshots before and after update).

--- End quote ---

Actually, Rigol does use the "2.0" term on the PCB silkscreen, but I assume that is just to specify the PCB revision.  I would guess that the hardware version shown (someone said set by the smd resistors), is based on the populated components.  So, even with the "2.0" PCB you may get different 1.0.2.0.x numbers.  Perhaps this is how they are trying to get away with a DS2302A model when they didn't sell a DS2302 model (tweaked input stage, etc.).  Anyhow, the 1.0.2.0.x number is the one that really matters and as you pointed out, it doesn't change with firmware changes.

alank2:

--- Quote from: cidcorp on January 21, 2014, 02:42:46 pm ---[1] Two questions though relating to the DS1000Z's - is there an EXTENDED system/info button trick like the DS2000 ie F7-F6-F7-etc (sorry going from memory which is horrible) for
HW revision FW revision info?
[2] Am I missing something or are both Left and Right menus permanently on screen???

--- End quote ---

#1 - I asked this question and no one could answer.  One person was able to do it, but he can't remember exactly how.
#2 - They are permanently on the screen, they don't hide.
Navigation
Message Index
Next page
Previous page
There was an error while thanking
Thanking...

Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod