Products > Test Equipment

Sniffing the Rigol's internal I2C bus

<< < (553/899) > >>

nmz787:

--- Quote from: alank2 on January 31, 2014, 01:56:47 pm ---nmz787 - use the scpi uninstall command (somebody posted a tool to do this not long ago) and then reboot your scope.  Then reinstall a new key without the 500uv option.

--- End quote ---

alank2,
Can you be a bit more specific about the tool. I'm new around here. I found the RUU tool, downloaded NI VISA 5.4, rebooted my PC, and attempted to connect, but then the RUU tool errored out and then crashed on my with an array-out-of-bounds error. (I was clicking connect too fast or something). After entering the correct IP address with the weird prefix and suffix, the :: stuff, it stopped complaining about not being able to find the instrument, and doesn't ask for the IP anymore upon starting the software and clicking connect. Now it just presents a message box "DSO not responding to query and/or command - RUU closing connection"

I'm downloading the UltraSigma installer now from the DS4000 Rigol page... I can't tell from the 'instructions' on RUU (which of course aren't in a README in the .zip) whether this is needed or not.

zombie28:

--- Quote from: tiagobaracho on February 01, 2014, 08:16:38 pm ---Guys... Sorry to bother..
I bought one Rigol DS2072A
It shows Software version 00.02.00 and Hardware version 2.0... Is that possible to use the 200 mhz and high memory settings ?
I have been reading a lot of pages in this thread but i could not find....
Thanks

--- End quote ---

You can use either my first firmware patch (https://mega.co.nz/#!FFk10SCY!UuWPXyqZwmca00pa2clOth1ryh1Z-AAgJg2yibfoUw0) with old keygen (riglol.3owl.com) or my newest patch from the post above with the new tirulerbach's keygen (if he decides to publish it).

alank2:

--- Quote from: nmz787 on February 01, 2014, 09:19:04 pm ---alank2, Can you be a bit more specific about the tool. I'm new around here.

--- End quote ---

https://www.eevblog.com/forum/testgear/sniffing-the-rigol%27s-internal-i2c-bus/msg375454/#msg375454

I don't know much about it, haven't tested it, but it says it can issue an uninstall command...

tiagobaracho:

--- Quote from: zombie28 on February 01, 2014, 09:25:36 pm ---
--- Quote from: tiagobaracho on February 01, 2014, 08:16:38 pm ---Guys... Sorry to bother..
I bought one Rigol DS2072A
It shows Software version 00.02.00 and Hardware version 2.0... Is that possible to use the 200 mhz and high memory settings ?
I have been reading a lot of pages in this thread but i could not find....
Thanks

--- End quote ---

You can use either my first firmware patch (https://mega.co.nz/#!FFk10SCY!UuWPXyqZwmca00pa2clOth1ryh1Z-AAgJg2yibfoUw0) with old keygen (riglol.3owl.com) or my newest patch from the post above with the new tirulerbach's keygen (if he decides to publish it).

--- End quote ---
Thanks man..
Have it been tested on DS2072A with   Hardware version 2.0 ? yours is 2.0 ?
Does its keeps even after reboot? IF i use DSHH ( add all) would it have any negative side ? I just ask because i saw that you can choose fewer options, so i thought " why would someone choose not all options ?
Which difference of both your versions ? the newest and the older ? i cannot use the newest unless tirulerbach's keygen is out right ? (sorry, i am into using it, not the hacking( i have not enough knowledge, but would love to use it and post back the results.
Thanks very much.

nmz787:

--- Quote from: alank2 on February 01, 2014, 09:29:34 pm ---
--- Quote from: nmz787 on February 01, 2014, 09:19:04 pm ---alank2, Can you be a bit more specific about the tool. I'm new around here.

--- End quote ---

https://www.eevblog.com/forum/testgear/sniffing-the-rigol%27s-internal-i2c-bus/msg375454/#msg375454

I don't know much about it, haven't tested it, but it says it can issue an uninstall command...

--- End quote ---


I ended up downloading the ~500 Mb Rigol Ultra Sigma software
--- Code: ---http://us.rigol.com/prodserv/DS4000/software/
--- End code ---
and after entering the IP address of the scope, and right-clicking on the unit, I found the SCPI terminal and issued
--- Code: ---:SYSTem:OPTion:UNINSTall
--- End code ---
, rebooted the scope, and found all options uninstalled (though I couldn't tell if this 100MHz unit reverted to 70MHz). Then I went back to the own3 site and put in the serial # and the options needed to reinstall. Removed the hyphens (-) from the pop-up messsage code, then pasted that just after this command in the SCPI terminal:
--- Code: ---:SYSTem:OPTion:INSTall licenseCode
--- End code ---

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod