Products > Test Equipment
Sniffing the Rigol's internal I2C bus
dr.diesel:
--- Quote from: sacherjj on February 13, 2014, 12:25:00 pm ---Data point: DS4054 received from TEquipment on Tuesday has 00.02.00 Firmware and 1.2 Hardware.
--- End quote ---
FYI, firmware 2.01 is out, which fixed some protocol decoding issues I was having.
asrc1978:
Hello everybody,
Below you can find the instructions to migrate from standard DS2102 non A (100MHz) to an oscilloscope of 300MHz (DS2302) without any cable connection or teardown:
1) The original FW of my DS2102 System Information screen was:
Manufacturer: RIGOL TECHNOLOGIES
Model: DS2102
Serial: DS2A#########
Software version: 00.00.01
Hardware version: 1.0
2) At the begining I only use the software "Rigol Keygen v2.0b1" to generate the licence key marking/filling the following options in the software:
- Memory (56M)
- Serial Decode
- Advanced Triggers
- DS2202
- Official
- Option code = DSAZ
- Private Key = 8EEBD4D04C3771
The program generate the following licence key (don't use it in your DS2xxx because maybe don't work properly):
----------------------------------------------------
JDMNBSJ-W8SX28S-VLNA5W3-TAVGZYS
----------------------------------------------------
Introduce the licence key using Utility->Options->Setup->Editor (ON).
Link to download the software:
http://www.gotroot.ca/rigol/RiGen-2b1.zip
After enter de licence key and accept it you can restart the oscilloscope and observe in the menu "Installed Options" that new characteristics now are enable.
3) After the installation of new characteristics you can migrate the FW to v00.01.01.00.02. One good thing is that the "Installed Options" where there after migration.
Manufacturer: RIGOL TECHNOLOGIES
Model: DS2202
Serial: DS2A#########
Software version: 00.01.01
Hardware version: 1.0
In the "System Info" screen you can see perfectly the new model of the oscilloscope "DS2202" and in the "Installed Options" the following characteristics available:
- 56MB of memory available.
- Advanced Trigger options available (including Windows, NthEdge, HDTV, Delay, Timeout, Dur, USB).
- Decode (RS232, SPI and I2C, until now without CAN protocol).
- Bandwidth 100M and 200M.
4) We will migrate again the FW to the new version 00.02.01.00.03 (last version until February 13th 2014).
In this case the idea is to migrate the oscilloscope to the last version and then generate a new licence key, now using "Riglol 1.03c" web page and not any software.
The link is:
http://riglol.3owl.com
To do it you will need to complete again the following options:
Serial: DS2A#########
Options: DSCA (here only use the code of 300MHz version because we need only enable this option)
Privatekey: 8EEBD4D04C3771
Press "Generate" and you will obtain the new licence key:
----------------------------------------------------
FD74GJQ-KLSEP6S-RVSCZNN-878KAWA
----------------------------------------------------
Introduce the new licence key using Utility->Options->Setup->Editor (ON).
Restart and "bualá" you will obtain a 300MHz oscilloscope.
Please if you need something write to me!
Best regards,
Seba from Argentina.
danb35:
...or just install the current firmware, generate and install one license key. Is there something new that I'm missing here, or is this all documented in the "Rigol I2C bus" thread?
true:
--- Quote from: danb35 on February 14, 2014, 02:48:23 am ---...or is this all documented in the "Rigol I2C bus" thread?
--- End quote ---
...which has turned into the "I don't computer so help me keygen my scope" thread.
Yeah, all the info is in there, between the "help me" and "another success! I feel important" posts.
jorges:
Off-topic: @Seba, where did you buy your ds2102 from? I'm also in Argentina struggling to find something else than Owon, Siglent and the now-old ds1052e
Jorge
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version