Products > Test Equipment
Sniffing the Rigol's internal I2C bus
true:
--- Quote from: Zone1 on May 17, 2014, 03:54:52 am ---
--- Quote ---5. When you are done enter the Option Code manually in the DS1000z using a single string without using any 'dash' (-) using Rigol's Procedure for activating the Trial Options in the D1000z. As I recall the procedure is available on Rigol's Web Site under DS1000z.
--- End quote ---
I had some difficulty finding the procedures on Rigol's web site for a DS1074Z can someone help? I could not find that specific model.
--- End quote ---
It's also been documented a lot in this thread. Two ways:
1. On-screen input, it's pretty self-explanitory.
2. SCPI with :SYStem:OPTion:INSTall <key-without-dashes>
Zone1:
--- Quote ---I had some difficulty finding the procedures on Rigol's web site for a DS1074Z can someone help? I could not find that specific model.
--- End quote ---
It's also been documented a lot in this thread. Two ways:
1. On-screen input, it's pretty self-explanitory.
2. SCPI with :SYStem:OPTion:INSTall <key-without-dashes>
[/quote]
This is what I found for the On-screen process. Is this everything?
There is much discussion about finding files, downgrading firmware, copying to usb, loading etc when it appears to be a simple procedure of going to the riglol.3owl site getting a key and using the procedure below to enter 28 digits . Am I missing something?
--- Quote --- Now that you have your System information handy...
You'll need to know how to input the Unlock key, when the time comes.
Here is how you get to the menu to input the unlock key..
in your scope Press the "UTILITY" Button that is located at the top of the scope
Now.. Select the "OPTIONS" option by pressing the button to the right of the word "OPTIONS" (if you can't see "OPTIONS" find the very bottom blue arrow buttons and scroll down to get the option "OPTIONS")
at this stage you have the option to select "INSTALLED" (if you do, this will show you What options are Trial version and how much time is remaining on them.
this is the section that you want to come back to you , later, to confirm that the upgrade worked
FOR NOW
Select "SETUP"
NOW.. on this screen the top option will be called "EDITOR" if Editor is OFF (Switch it on, by Pressing the button to the right of EDITOR)
NOTE: if at any point the Menu Bar dissappears, You can make it re appear by Pressing the BLUE "MENU" Button at the top of all the other buttons on the right side of the screen
and just a quickie (if the menu thing gets annoying, you can set the time at which the menu will dissapear by selecting..
"DISPLAY" Button at the top
"MENU DISPLAY"
Select the Amount of "S" (Seconds you wish) or "Infinite"
NOW, back to the point
Under Utility/Options/Setup
Use the "Intensity" Knob, that is located at the very top of the Scope, next to the Blue "MENU" button
turn it to select your character that you need to input
Push the knob in until you get a click, this will select your character
THIS IS THE AREA WHERE YOU INSERT YOUR UNLOCK KEY
--- End quote ---
ted572:
--- Quote from: Zone1 on May 17, 2014, 03:54:52 am ---
I had some difficulty finding the procedures on Rigol's web site for a DS1074Z can someone help? I could not find that specific model.
--- End quote ---
Zone1: Please go to > https://www.eevblog.com/forum/testgear/sniffing-the-rigol%27s-internal-i2c-bus/msg425534/#msg425534
If you are still having trouble this should help you. It is for the DS1074Z and will give you (Sorry - Not 200 MHz - my Error, corrected 5/19/2014) "100 MHz BW", etc., and should get you going. If not please let me know. Cheers, Ted
linux-works:
confirmed that the web-based unlock procedure works fine for the latest shipping (from tequipment.net) 1074z.
thanks to everyone's good work on this; its what pushed me into this specific model/brand purchase ;-)
AndersAnd:
--- Quote from: ted572 on May 17, 2014, 11:34:27 pm ---
--- Quote from: Zone1 on May 17, 2014, 03:54:52 am ---
I had some difficulty finding the procedures on Rigol's web site for a DS1074Z can someone help? I could not find that specific model.
--- End quote ---
Zone1: Please go to > https://www.eevblog.com/forum/testgear/sniffing-the-rigol%27s-internal-i2c-bus/msg425534/#msg425534
If you are still having trouble this should help you. It is for the DS1074Z and will give you 200 MHz BW, etc., and should get you going. If not please let me know. Cheers, Ted
--- End quote ---
200 MHz? Doesn't DS1000Z only support 70 and 100 MHz options?
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version