Products > Test Equipment
Sniffing the Rigol's internal I2C bus
Tilman:
--- Quote from: Purevector on June 27, 2014, 02:27:52 am ---Ok, I got 300MHz upgrade and all options working on my DS2072A which was not able to upgrade to 300MHz. Here is what I did:
1-Install all options, no bandwidth upgrade (NSEH) using rigup or the upgrade utility.
2-Use rigup to get license for NS8N (All options - 56M + 300MHz) and install on scope in any of the methods described in this thread.
The result will be a scope with all options AND 300MHz!!! Success! :-+
By the way, you can't use the upgrade utility to install NS8N since that program always uninstalls all options before installing new ones.
--- End quote ---
not working for me, NSEH -> License is unavliable....
only NSEQ works for me... |O
BTO:
MY God, 229 Pages and counting... I can't believe this thread is still going LOL
It's Alive... Alive.
Ok. to get serious for a second
I have a Rigol DS2072A,
it was loaded with the 2.0 Software from the factory,
it was originally 70 MHz
Now SUCCESSFULLY UPGRADED TO 300MHz
All options Unlocked and 56 Mpt Memory Depth
IF ANYONE NEEDS ANY HELP, I AM HERE TO HELP, and Im happy to do it
So.. Newbies if you have a DS200A
let me know
I know this is a Huge thread, I've gone through it in great detail
NO NEED TO DOWNLOAD ANYTHING
I'll supply it all From a Cloud
if enough people want it
I'll Just upload it for all of you to have access to , For.. Say,.. a Month or so, if you like
However it's easier if you guys just skype me, that's what a few people have been doing
There's 2 Main Issues that Get everyone
1. Make sure that your Scope is Set to COMPUTER for the USB Port,
if it's set to PictBridge and considering that the front USB is PictBridge, Your Scope wont detect
in the computer and you'll be scratching your head as to why
2. Putting the Scope into Firmware Update Mode is a little tricky and takes a correct explanation.
which is where skype comes in.
the answer to issues 1 is go to
UTILITY / IO SETUP / USB DEVICE Make sure the value says COMPUTER
the answer to 2 is
Start with Scope OFF
Now.. before switching it ON
Find the Power Button, DON'T PRESS IT YET, Put your left thumb on the power button
Now, with your Right Thumb find the ORANGE HELP Button, Put your thumb on it
Now.. Press the power button and STRAIGHT AWAY Press the HELP button,
don't wait to see the RIGOL screen
if you see the rigol screen you need to do it quicker
YOU WILL KNOW THAT YOU HAVE DONE IT CORRECTLY IF.......
the button in the top right corner labelled SINGLE Turns Solid Orange
that means the meter is upgrade Mode
Now pop in your USB stick and the CH 1 Button should flash Green
this indicates good communication with the USB Device and you just Wait 2 mins and it's done
if anyone needs any further assistance, Let me know
I'm at
martin@btotechnicalexperts.com.au
be cool guys
MrKrabs:
--- Quote from: samertje on June 27, 2014, 03:55:00 pm ---
--- Quote from: samertje on June 26, 2014, 04:27:04 pm ---Good day!
We received a Rigol DS4014 yesterday. I scanned and read through this huge thread and also found this directory:
http://www.gotroot.ca/rigol/
As I understand, to upgrade to 500MHz I need to use the DS2000A upgrade utility and the DS4000update_00.02.01.00.03.GEL
Can anyone confirm this?
Also want to upgrade my DG4062. How to do this?
Cheers
Sam
--- End quote ---
So I was wrong. I'm not finding the right info in this thread. Anyone please help?
Link to how to upgrade?
Hopless, but happy
Sam
--- End quote ---
For the DS4000, you only need MrKrab's firmware at http://www.gotroot.ca/rigol :)
samertje:
--- Quote from: MrKrabs on June 29, 2014, 11:23:45 pm ---
For the DS4000, you only need MrKrab's firmware at http://www.gotroot.ca/rigol :)
--- End quote ---
1. I used MrKrabs firmware on a compatible stick
2. Booted into blackscreen using help button
3. Entered the stick in the USB. Channel 1 didn't blink, but immeadiatly went solid together with run/stop button solid red
After this nothing happens. I hope this helps some of you...
Any help?
Thank you for all replies :)
BloodyCactus:
did you test the usb stick by saving a screen image to it to make sure the ds4k can see it properly?
on my ds2k, I had to wait a bit before putting the usb stick in, too quick and it did not seem to load. tried again, waited like 30 seconds after the button presses then put it in and it recognised it correctly right away.
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version