Products > Test Equipment

Sniffing the Rigol's internal I2C bus

<< < (709/899) > >>

Jog:
Hello together,

sorry I am absolutly new but I hope I get help here. I bought a new DS2072a and try to "update" it into a ds2302a with all options, but without any success.

a) the firmware is 00.03. sp1 (from delievery on) so I can't downgrade into the 00.02. for the windows based upgrade (*IDN? with all info) = I became only the SN in 13! not 14 digits and nothing else.
b) rigkey under linux can only generate a key with a 14 digit SN (if I add a 0 at the end, it dosn't help and also the option DSA9) will not accepted due to his lenght and that because it fits?!

I work now since 2 days on a possibility and see no further possibilities  :'(

For every hints I'm very thankeful!

many thanks if anybody can help!

Mark_O:

--- Quote from: leppie on September 16, 2014, 05:19:16 am ---At over 100 pounds cheaper (perhaps translated to ~$150) the DS1054Z would be a real bargain if hackable.  :-+

Edit: $399 at tequipment!!! Even cheaper http://www.tequipment.net/Rigol/DS1054Z/Digital-Oscilloscopes/

--- End quote ---

A 4-channel scope, especially with the performance of the 1000z-series, is really mind-boggling at that price-point!  That becomes a no-brainer for those on a limited budget, looking for whatever they can find at a low price... unless they're sure they'll never need more than 2-channels, and are strapped for very dinero.

poorchava:
Hi, I'm thinking about purchasing DS1054 or DS1074 and obviously "upgrading" it. I am aware of the Riglol tool, but it needs a private key. I went through all the posts in this topic, but all this is greatly confusing.

In the end: what are the missing steps for upgrading the scope in the sequence below?

-upgrade FW to latest version
-read serial of the device
-get private key
-input serial and desired options into Riglol tool
-enjoy!

Does getting the private key still involve taking scope apart and dumping memory? I haven't seen any post that would say otherwise, but I just wanted to make sure.

frenky:

--- Quote ---1. Type in your unit's Serial Number.
2. Type in DSER for all options without the 500µV. This Option may not be in the Keygen's list, but it will work!
3. Do NOT enter anything for 'Privatekey', it will be inserted automatically for you (based on the DS1000z).
4. Press [GENERATE], and record the resulting Option Code.
5. When you are done enter the Option Code manually in the DS1000z using a single string without using any 'dash' (-) using Rigol's Procedure for activating the Trial Options in the D1000z.
--- End quote ---
https://www.eevblog.com/forum/testgear/is-rigol-ds1074z-hackable-to-increase-bandwidth-to-100/msg499411/#msg499411

PepeK:

--- Quote from: Jog on September 17, 2014, 11:11:10 am ---Hello together,

sorry I am absolutly new but I hope I get help here. I bought a new DS2072a and try to "update" it into a ds2302a with all options, but without any success.

a) the firmware is 00.03. sp1 (from delievery on) so I can't downgrade into the 00.02. for the windows based upgrade (*IDN? with all info) = I became only the SN in 13! not 14 digits and nothing else.
b) rigkey under linux can only generate a key with a 14 digit SN (if I add a 0 at the end, it dosn't help and also the option DSA9) will not accepted due to his lenght and that because it fits?!

I work now since 2 days on a possibility and see no further possibilities  :'(

For every hints I'm very thankeful!

many thanks if anybody can help!

--- End quote ---

Read this : https://www.eevblog.com/forum/testgear/rigol-mso2000-series-hacking/?topicseen

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod