| Products > Test Equipment |
| Sniffing the Rigol's internal I2C bus |
| << < (831/899) > >> |
| Howardlong:
--- Quote from: qwertymodo on September 16, 2016, 08:29:15 pm ---Just bought a MSO1074Z-S, and unfortunately it came with firmware 4.03.SP2. Board revision is 6.1.2, if that makes any difference. Obviously, me asking when riglol/rigup will support the new firmware is of no use to anybody, but is there anything I can do that would be helpful at this point? I haven't managed to grab the memory dump yet, but I do have the tools to do so, and I'll try to get that done this weekend. --- End quote --- It's definitely worth doing, I have the same model, it's my go-to field scope. It just takes a little patience, and care with the warranty sticker. My main negatives are the screen-only serial decodes, cluttered screen and slow UI, but for the money I'm certainly not going to complain, it gets the job done in a very compact and usable package |
| qwertymodo:
I have my memory dumps if they are of any use to anybody with the know-how to work toward updating rigup. There was a message somewhere earlier in this thread where somebody claimed to have gotten working licenses on 4.03.SP1 by dumping the memory while the Rigol logo was on-screen, so I took one then too. I'm willing to do anything else that might be useful. I already have a DS1054Z fully unlocked, so I'm not in any huge rush (though I would like to sell the '54 once I get the MSO unlocked). Sent from my m8wl using Tapatalk |
| psysc0rpi0n:
--- Quote from: Howardlong on September 19, 2016, 12:20:10 am --- --- Quote from: qwertymodo on September 16, 2016, 08:29:15 pm ---Just bought a MSO1074Z-S, and unfortunately it came with firmware 4.03.SP2. Board revision is 6.1.2, if that makes any difference. Obviously, me asking when riglol/rigup will support the new firmware is of no use to anybody, but is there anything I can do that would be helpful at this point? I haven't managed to grab the memory dump yet, but I do have the tools to do so, and I'll try to get that done this weekend. --- End quote --- It's definitely worth doing, I have the same model, it's my go-to field scope. It just takes a little patience, and care with the warranty sticker. My main negatives are the screen-only serial decodes, cluttered screen and slow UI, but for the money I'm certainly not going to complain, it gets the job done in a very compact and usable package --- End quote --- Are you sure the list of compatible JTAG adapters are in message #2413??? On page 97??? I found that message but it has no list of JTAG adapters. Anyway, I'm trying to find something cheaper than the Olimex LTD ARM-USB-OCD-H . This is quite expensive! I was thinking about this one which is a lot cheaper: http://dangerousprototypes.com/docs/Bus_Pirate_v3.6 Is this one suitable for this job? |
| hammy:
--- Quote from: psysc0rpi0n on September 19, 2016, 07:59:19 am ---Are you sure the list of compatible JTAG adapters are in message #2413??? On page 97??? I found that message but it has no list of JTAG adapters. --- End quote --- Yes, I'm sure, it was the first message from buergi: "Reply #2413 on: 11-01-2014, 18:59:55" There are also several other messages in this thread from various people with various jtag adapters. Just do a search inside this thread. Or do it the other way around. You found a cheap adapter? Search the forum if someone used this model before. Cheers hammy |
| psysc0rpi0n:
--- Quote from: hammy on September 19, 2016, 10:12:43 am --- --- Quote from: psysc0rpi0n on September 19, 2016, 07:59:19 am ---Are you sure the list of compatible JTAG adapters are in message #2413??? On page 97??? I found that message but it has no list of JTAG adapters. --- End quote --- Yes, I'm sure, it was the first message from buergi: "Reply #2413 on: 11-01-2014, 18:59:55" There are also several other messages in this thread from various people with various jtag adapters. Just do a search inside this thread. Or do it the other way around. You found a cheap adapter? Search the forum if someone used this model before. Cheers hammy --- End quote --- This is what I find in this thread at pos #2413. But I'll search by the date! See attachment |
| Navigation |
| Message Index |
| Next page |
| Previous page |