Products > Test Equipment

Tek CSA7404/TDS7000 repair project (Upgraded memory/CPU)

<< < (153/194) > >>

Yroger:
My ppc battery is ok !!
nvram dallas acquisition board battery is ok !! This is what is displayed now. it looks like it's progressing...a little...
What is displayed in the last lines, I am not a programmer and I do not see what he is talking about ??



--- Quote ---]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
      ]]]]]]]]]]]  ]]]]     ]]]]]]]]]]       ]]              ]]]]         (R)
 ]     ]]]]]]]]]  ]]]]]]     ]]]]]]]]       ]]               ]]]]           
 ]]     ]]]]]]]  ]]]]]]]]     ]]]]]] ]     ]]                ]]]]           
 ]]]     ]]]]] ]    ]]]  ]     ]]]] ]]]   ]]]]]]]]]  ]]]] ]] ]]]]  ]]   ]]]]]
 ]]]]     ]]]  ]]    ]  ]]]     ]] ]]]]] ]]]]]]   ]] ]]]]]]] ]]]] ]]   ]]]] 
 ]]]]]     ]  ]]]]     ]]]]]      ]]]]]]]] ]]]]   ]] ]]]]    ]]]]]]]    ]]]]
 ]]]]]]      ]]]]]     ]]]]]]    ]  ]]]]]  ]]]]   ]] ]]]]    ]]]]]]]]    ]]]]
 ]]]]]]]    ]]]]]  ]    ]]]]]]  ]    ]]]   ]]]]   ]] ]]]]    ]]]] ]]]]    ]]]]
 ]]]]]]]]  ]]]]]  ]]]    ]]]]]]]      ]     ]]]]]]]  ]]]]    ]]]]  ]]]] ]]]]]
 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]       Development System
 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]
 ]]]]]]]]]]]]]]]]]]]]]]]]]]]       VxWorks version 5.3.1
 ]]]]]]]]]]]]]]]]]]]]]]]]]]       KERNEL: WIND version 2.5
 ]]]]]]]]]]]]]]]]]]]]]]]]]       Copyright Wind River Systems, Inc., 1984-1997

                               CPU: Tektronix HPP - PowerPC 740.  Processor #0.
                              Memory Size: 0x2000000.  BSP version 1.0.3.5.
                             WDB: Ready.

usrNvFsInit: NAME=/nvram BASE=0xfd0ff100 BPB=512 BPT=8 NB=8 BO=0
nvfs: STATUS: Mounting existing NVRAM file system
KERNEL: THERMAL CONTROL INITIATED
Executing startup script c:\dio_rst.vsh ...
dbFsIoctl: invalid code 3
    ################### topScript starts ###############################




         cd "dbfs:c:/dio_rst.vsh"

value = 0 = 0x0


value = 0 = 0x0

"value" is overloaded - Please select:
    1: value__C24RWHashDictionaryIteratorP13RWCollectable
    2: value__C24RWCollectableAssociation
    3: value__C24RWHashDictionaryIterator
    4: value__24RWCollectableAssociationP13RWCollectable
Enter <number> to select, anything else to stop: new symbol "value" added to symbol table.
value = 0x1d90c00: value = 0 = 0x0

Done executing startup script c:\dio_rst.vsh
KERNEL:  RUNNING TIME SLICED AT 10 TICKS PER SLICE!

--- End quote ---


--- Quote ---then run a clearDB ( see topscript)
--- End quote ---

Where can i find it?

charlyd:
@Yroger

replace your NVram and follow the procedure  as written many times here in the topic. 
99% of al the weird messages and corruption while booting are Dallas - NVram related !!


these errors like in the log are NVRam related it is not only the battery which is important .. just swap out.  the nvram

- booting ->  re-enter the right bootsetting
- clearDB -procedure (topscript.hw)  !!  unhide  system folders in windows and you l find vxboot dir in the root of c:\  ( make a complete copy before your edit anything )
- rebuild NVram content from you eeprom field cal.  by booting few times and follow the debug what is happening.

after putting back the remark in line # clearDB.....     2 more reboots should do the work

btw post here your boot settings please. so we can check if they are good

Yroger:
Good morning,
as said previously I have no Vxboot folder on the hard drive even when displaying the hidden folders and files of the system !! Maybe it's named differently as the scope is from the 8000 series... I only found files that looked a bit similar in the firmware folder see below:

[url=https://ibb.co/jDwsdNf][/url]

Thank you for help

charlyd:
ok.check in your boot settings after you connected to you debug port.  with a terminal progr. and check if the correct files is set.

charlyd:
i have a TDS7154 for repair with option  Available 60.  displayed
i guess it is TDSET2 because  ET2 is written on the back i have option software TDSET3 (TDSET2 is not downloadble anymore) but that does not clear my avail. 60 in the option screen  does anybody still have the install file TDSET2 or know how to get rit of the available 60. in the option screen list. when using TDSET3 software.

is this a registry setting or something? where Ethernet Compliance is getting filled in?

i still have old OS (chinese version) where parts of the option are visible in some folders as tdset2 folder, what do i need?

Navigation

[0] Message Index

[#] Next page

[*] Previous page