Products > Test Equipment

Tektronix THS7xxx Scope Hack/Teardown/Discussion - FW 1.16 found

<< < (74/95) > >>

Zucca:
Update the first post with mrprecision good work.

I still have on my list the FW upgrade without losing the cal data.
One day it will happen.

PIC18F2550:

--- Quote from: Zucca on August 29, 2021, 12:53:08 pm ---Update the first post with mrprecision good work.

I still have on my list the FW upgrade without losing the cal data.
One day it will happen.

--- End quote ---

thank zocca

I don't think this is an update problem ,my FW is FV:v1.16

mrprecision:

--- Quote ---hello mr precision, if you can add this option to read all mesured ?, i need this option because i using this oscilloscope for analyze frame of Protocol I2C/SPI/RS232/CANbus/JTAG please see the Picture canbus message of edc16c34 to my pic18f4580 this Picture is no full in ".bmp" files ,and see picture 2 of I2Cbus it full

thank to you for this soft and sorry for my bad enlish
--- End quote ---

I actual don't understand the problem. I only can read you what is shown in the display. Can someone help me to understand the problem?

PIC18F2550:

--- Quote from: mrprecision on August 30, 2021, 07:21:19 pm ---
--- Quote ---hello mr precision, if you can add this option to read all mesured ?, i need this option because i using this oscilloscope for analyze frame of Protocol I2C/SPI/RS232/CANbus/JTAG please see the Picture canbus message of edc16c34 to my pic18f4580 this Picture is no full in ".bmp" files ,and see picture 2 of I2Cbus it full

thank to you for this soft and sorry for my bad enlish
--- End quote ---

I actual don't understand the problem. I only can read you what is shown in the display. Can someone help me to understand the problem?

--- End quote ---

hello mr precision

you using the read fonction by address or by CMD/SETING name ? , try to use Horizontal Commands for set the number of full points in waveform
(2500 points) before reading

i use the C l'anguage for program my software , i can using the rs232 port if you can share the source file ? , i try to add new fontion by rewrite your code in C language

in "Programmer Manual" try to read all text from page 59 to 64 see (2.29) in page 59

--- Code: ---Waveform Commands
Waveform commands let you transfer waveform data points to and
from the instrument. Waveform data points are a collection of values
that define a waveform. One data value usually represents one data
point in the waveform record. When working with enveloped
waveforms, each data value is either the min or max of a max/min
pair. Before you can transfer waveform data, you must specify the
data format, record length, and waveform locations.

--- End code ---
and see (2.30) in page 60

--- Code: ---Waveform Data/Record Lengths. You can transfer multiple points for
each waveform record. You can transfer a portion of the waveform or
you can transfer the entire record. The DATa:STARt and DATa:STOP
commands let you specify the first and last data points of the
waveform record.When transferring data into the instrument you must specify the
location of the first data point within the waveform record. For
example, when DATa:STARt is set to 1, data points will be stored
starting with the first point in the record, and when DATa:STARt is
set to 500, data will be stored starting at the 500th point in the record.
DATa:STOP will be ignored when transferring data into the
instrument as the instrument will stop reading data when there is no
more data to read or when the record length has been reached.
When transferring data from the instrument you must specify the first
and last data points in the waveform record. Setting DATa:STARt
to 1 and DATa:STOP to 2500 always returns the entire waveform.

--- End code ---

thank to you and sorry for my bad english

1audio:
I think you are asking to pull the data from the scope in a format that would allow for decoding the various serial formats you mentioned.  Please confirm. And be more specific about the format you need the scope output in if not the native format Tek used..

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod