| Products > Test Equipment |
| Test Equipment Anonymous (TEA) group therapy thread |
| << < (25314/27435) > >> |
| grizewald:
More Datron 1071 As I said in my last post about this meter, there's no such thing as a perfect one when you're talking about something from the mid '70s. Mine was no exception, and although the meter powered up straight away when I received it and seemed to give plausible results when reading a few voltage references and precision resistors, it was obvious that the meter wasn't entirely happy. First task was to check the infamous Philips blue electrolytics. Sure enough, with one end freed from the PCB, they measured: Des. Printed Actual ESR Value Value C45 47μF 34μF 8.1Ω (Furthest away in the photo) C46 47μF 34μF 6.4Ω C47 33μF 28μF 8.1Ω C48 33μF 25μF 10.2Ω C49 10μF 9.7μF 4.5Ω C50 10μF 9.4μF 7.6Ω The replacements from Kemet and Vishay were a bit of a squeeze, but had rather better parameters: Des. New New Value ESR C45 50μF 0.22Ω C46 49.7μF 0.22Ω C47 32.2μF 1.38Ω C48 31.5μF 1.44Ω C49 11.7μF 0.55Ω C50 11.7μF 0.55Ω I then checked the various power rails and found out of tolerance voltages and excessive ripple, so it was time to turn my attention to that area of the meter. This is where the fun starts! The power supply is implemented on the board that runs across the rear of the meter. Between that and the rear of the case, Datron also crammed in all of the boards that handle the optional outputs, the front/rear relays and the two stacked toroid transformers. It's kind of packed in there as you can see from the photo below. The only way I could easily work on the power supply was to separate the rear of the case with all its boards from the rear PCB and remove the analogue, digital and current boards so that I had clear access to the solder side of the PSU. I wasn't keen on my chances of being able to put it all back together again without extensive photo documentation of what plug went where - there are no identifying labels on any of the plugs that connect everything together, so I took my time and took many photos along the way. Finally, the rear of the case was free! continues in next post (which will be after I've eaten some strawberries and cream )... |
| Specmaster:
--- Quote from: bd139 on July 17, 2022, 10:38:08 am ---465 should clean up nicely. Wonder if it works. Plug was cut off everything on the stand --- End quote --- Good all the knobs and shafts look to be OK, not bent from being clobbered or dropped, so it should clean up very nicely indeed, looking good so far. |
| bd139:
--- Quote from: mnementh on July 17, 2022, 03:52:39 pm --- --- Quote from: bd139 on July 17, 2022, 11:05:29 am --- ...In other news, frozen pigs just flew out of hell… it looks like it actually works. Have ID’ed the probe sensor doesn’t work properly on one of the channels but that’s an easy fix. Might even work with a clean. --- End quote --- For 20 quid...? Def territory! mnem :clap: --- End quote --- Not quite. Full clean and check out… Issues with channel switching. Looks like dirty switches and possibly a duff probe on my part. Hmm. |
| mnementh:
--- Quote from: grizewald on July 17, 2022, 10:02:15 am ---Greetings TEA folk! It's been far too long since I was here last, mainly due to a serious lack of time due to work pressure. As I'm on a nice long vacation from work at the moment, I spent a few days catching up on things here (as best one can for 2000+ pages) and have thoroughly enjoyed myself. Despite having been pretty much overloaded with work, my GAS problem has continued unabated. --- End quote --- Welcome back, BTW... it has been too long. A while ago I bought this T-shirt for my daughter: It reminded me of our conversations about the Koloboks. :-DD mnem *toddles off to shop some spray varnish* |
| Specmaster:
--- Quote from: bd139 on July 17, 2022, 11:29:40 am ---Put some bananas in before the potatoes too :) Solartron. Also works apart from two missing decimal points. I swapped a couple of the rather ancient LED displays around expecting that to be the issue but it wasn’t. Hopefully the main IC isn’t at fault :( Should read 9.6245. Got to go do some shopping now :( --- End quote --- If those LEDs are socket based, more than likely to be bad contacts, give it a shot of contact cleaner and a few insertions and extractions to wipe the contacts? |
| Navigation |
| Message Index |
| Next page |
| Previous page |