Products > Test Equipment

The Siglent SDG1000 and SDG800 thread

<< < (64/81) > >>

DG5SAY:

--- Quote from: tautech on December 06, 2016, 11:00:06 pm ---
--- Quote from: DG5SAY on December 06, 2016, 02:34:34 pm ---
--- Quote from: tautech on December 06, 2016, 08:25:11 am ---Haven't had a chance to update my SDG1010 yet but when I do if it defaults to Mandarin they'll be hearing about it.  :box:

--- End quote ---

After the update to 1.1.1.38R2 the default language after the first reboot is: Mandarin !  :-DD
And yes, I needed the help of Reply #309 !
Be sure that you set the default state to "Last" after change to English language.

--- End quote ---
Confirmed.  >:(
Why would they do that ?  :-//

--- End quote ---

because of "Yolo" (https://www.eevblog.com/2015/12/03/eevblog-826-siglent-ceo-eric-qin-visits-the-eevblog-lab/)

tautech:

--- Quote from: DG5SAY on December 08, 2016, 07:02:34 am ---
--- Quote from: tautech on December 06, 2016, 11:00:06 pm ---
--- Quote from: DG5SAY on December 06, 2016, 02:34:34 pm ---
--- Quote from: tautech on December 06, 2016, 08:25:11 am ---Haven't had a chance to update my SDG1010 yet but when I do if it defaults to Mandarin they'll be hearing about it.  :box:

--- End quote ---

After the update to 1.1.1.38R2 the default language after the first reboot is: Mandarin !  :-DD
And yes, I needed the help of Reply #309 !
Be sure that you set the default state to "Last" after change to English language.

--- End quote ---
Confirmed.  >:(
Why would they do that ?  :-//

--- End quote ---

because of "Yolo" (https://www.eevblog.com/2015/12/03/eevblog-826-siglent-ceo-eric-qin-visits-the-eevblog-lab/)

--- End quote ---
I doubt very much if Eric has any clue about this, but I do know this FW and its default to Mandarin is on his Product Managers desk.  :horse:

Pirapoense:

--- Quote from: DG5SAY on December 05, 2016, 05:15:30 pm ---
--- Quote from: Siglent America on December 02, 2016, 07:27:34 pm ---Some people might be interested in knowing -

There is a brand new FW update for the Siglent SDG1000 generators that removes the requirement of having to select a language at boot-up. (This is for models such as the SDG1025, SDG1050. This FW is not for the newer SDG1000X series of generators).

It can be found here:
http://siglentamerica.com/gjjrj-xq.aspx?id=4997&tid=15

--- End quote ---

OK, I updated to this version 1.1.1.38R2, seems to work fine, but the previous version 1.1.1.37R3 (more than one year old) also does not ask for the language at boot-up on my SDG1025!?

--- End quote ---

I also updated to 38R2 but comparing to 37R3 now I can not set dbm at Ampl menu because it appears the word "cancel" instead of "dbm". Any suggestion? Can I go back to 37R3? Regards.

rf-loop:

--- Quote from: Pirapoense on December 12, 2016, 12:57:02 pm ---
--- Quote from: DG5SAY on December 05, 2016, 05:15:30 pm ---
--- Quote from: Siglent America on December 02, 2016, 07:27:34 pm ---Some people might be interested in knowing -

There is a brand new FW update for the Siglent SDG1000 generators that removes the requirement of having to select a language at boot-up. (This is for models such as the SDG1025, SDG1050. This FW is not for the newer SDG1000X series of generators).

It can be found here:
http://siglentamerica.com/gjjrj-xq.aspx?id=4997&tid=15

--- End quote ---

OK, I updated to this version 1.1.1.38R2, seems to work fine, but the previous version 1.1.1.37R3 (more than one year old) also does not ask for the language at boot-up on my SDG1025!?

--- End quote ---

I also updated to 38R2 but comparing to 37R3 now I can not set dbm at Ampl menu because it appears the word "cancel" instead of "dbm". Any suggestion? Can I go back to 37R3? Regards.

--- End quote ---

Not tested with this model  (but with SDG5000).  Check that output level display is set for 50ohm.

Pirapoense:

--- Quote from: rf-loop on December 12, 2016, 01:39:30 pm ---
--- Quote from: Pirapoense on December 12, 2016, 12:57:02 pm ---
--- Quote from: DG5SAY on December 05, 2016, 05:15:30 pm ---
--- Quote from: Siglent America on December 02, 2016, 07:27:34 pm ---Some people might be interested in knowing -

There is a brand new FW update for the Siglent SDG1000 generators that removes the requirement of having to select a language at boot-up. (This is for models such as the SDG1025, SDG1050. This FW is not for the newer SDG1000X series of generators).

It can be found here:
http://siglentamerica.com/gjjrj-xq.aspx?id=4997&tid=15

--- End quote ---

OK, I updated to this version 1.1.1.38R2, seems to work fine, but the previous version 1.1.1.37R3 (more than one year old) also does not ask for the language at boot-up on my SDG1025!?

--- End quote ---

I also updated to 38R2 but comparing to 37R3 now I can not set dbm at Ampl menu because it appears the word "cancel" instead of "dbm". Any suggestion? Can I go back to 37R3? Regards.

--- End quote ---

Not tested with this model  (but with SDG5000).  Check that output level display is set for 50ohm.

--- End quote ---

You are absolutely right. It is necessary to "declare" what is the load (50 ohm in my case) to have the "dbm" in the Ampl menu.
Thanks and regards.

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod