any one wants to test infiray P2 pro? 9 gram thermal camera with macro lens.

[Rambo Sonny]

recently I found out that Infiray has released a new smartphone thermal imager called P2 pro. I have five units in hand now. Does anyone has interest in testing it? I can provide it for free. If you have smartphone thermal imagers from other manufacturers, you can compare them and share your thoughts under post. But I only have five, so let's set a deadline: for all who left messages I want a try below this post before Oct 15,2022, we will select five lucky ones.

[thermalengineer]

hey,
Sounds good. I'd like to test it, is it really for free? Any other requirements?

Thanks.

[Rambo Sonny]

free samples, nothing special.

[gabiz_ro]

I want a try
If is available outside US

[mikeselectricstuff]

I have one of these on the way for review

[Fraser]

I will test any thermal camera that comes my way if it is of interest to this forum. It has to be a “no strings attached” arrangement though. I was recently asked to buy a camera and would receive a refund if I produced a review that pleased the supplier. I am not interested in those sorts of ‘deals’. I produce honest detailed written technical reviews such as the one I did on the DYT CA-10 system

https://www.eevblog.com/forum/thermal-imaging/review-dianyang-technology-ca10-circuit-board-thermal-analyzer-repair-rd/

Contact me if interested in my input.

Fraser

[kripton2035]

I want a try
If is available outside US

[tomasis]

i want to try it. Im available in Sweden.

[ArsenioDev]

I'll put this thing through the paces, have NIST calibrated blackbodies and a wild range of equipment to test and validate with, additional supplementary lenses and additional hardware.

[Giuss]

I'd like to try it, if available outside US

Thanks

[Vipitis]

If you have any left to throw my direction, I would tear it apart and try it on my 150mm lens to spot the moon.

[Rambo Sonny]

sure, it is avaliable to US

[Rambo Sonny]

no problem

[Rambo Sonny]

coool mate. want to know how you think about it. you can leave comments here when you get it.

[Nezocas]

recently I found out that Infiray has released a new smartphone thermal imager called P2 pro. I have five units in hand now. Does anyone has interest in testing it? I can provide it for free. If you have smartphone thermal imagers from other manufacturers, you can compare them and share your thoughts under post. But I only have five, so let's set a deadline: for all who left messages I want a try below this post before Oct 15,2022, we will select five lucky ones.

I would love to try it and also make an honest review on it.
I work every day in electronics repair, and that camera shows a lot of details to make the job easier.
Lets hope you chose a Portuguese country 

Regards

[Rambo Sonny]

for sure will. thanks friend

[thermalengineer]

noted. Do you know what's the difference between p2 and p2pro?

[Rambo Sonny]

P2 Pro has a magnetic lens, that allows you can use camera very close to the ciucuit board.

[svgurus]

If you are in contact with manufacturer, please tell them to speed up making t3 series available for iphones)

[Fraser]

For those unaware, the P2 maximum temperature measurement is 170 Celsius but the P2 Pro is capable of measurements up to 550 Celsius. The Pro model therefore has both the high sensitivity and low sensitivity ranges enabled in its firmware.

As has been stated, the Pro also comes with a neat close-up lens that attaches to the front of the camera using magnets.

Fraser

[RBsonic]

I'd like try it too. I have allready HT-301 (here is my review: https://www.eevblog.com/forum/thermal-imaging/hti-ht-301-384-x-288/msg2814034/#msg2814034), so I can compare it.

[radiskull2000]

I would be happy to try one so long as it comes with no strings attached.

[Rambo Sonny]

I will try

[Rambo Sonny]

thanks. that would be pretty cool

[RO]

Would like to test your infiray P2 pro