Products > Thermal Imaging

FLIR E4 Wifi Resolution and Menu Hack Thread

<< < (231/246) > >>

Bud:
Enjoy your camera!

gearshredder:
Wow this thread is still going. Bud, you are doing amazing work.  :)

556:

--- Quote from: Weston on June 11, 2020, 05:10:36 am ---My flir E4 wifi arrived today and I the liberation procedure went smoothly! Thank you Bud for all the work do for the community on this!

For those looking on where to order the camera from, I ordered my flir E4 wifi from TEquipment a few months ago and it was backordered so it only recently shipped. The camera is hardware version 2.0L and software 3.16.0. The calibration card has a date of April 28, 2020, which is recent, so I would assume that there is no newer software than 3.16.0. I have not tried the advanced package yet.

For those not wanting to dig through endless pages of the thread:

I used the 3.12.0  files from here: https://www.eevblog.com/forum/thermal-imaging/flir-e4-wifi-resolution-and-menu-hack-thread/msg1397359/#msg1397359

and the new 3.16.0 dll from here: https://www.eevblog.com/forum/thermal-imaging/flir-e4-wifi-resolution-and-menu-hack-thread/msg2252082/#msg2252082

and instructions on how to put the camera in RNDIS mode from here (I had problems with the website so I had to access it through web archive) https://web.archive.org/web/20190409142550/https://fubar.gr/hacking-the-flir-e4/

This was done on a windows 10 desktop.

--- End quote ---

Thank you! I'm a total dumbass and did not realize that the download package contained the proper step by step guide (yea sometimes you should open the readme.txt  |O). I was endlessly searching the forum here for the 17-point guide everyone were refering to with no luck!

I just managed to unlock the E4 WiFi that arrived today. Calibration date 2021-11-25. HW version 2.0L and Software still 3.16.0.

By connecting the camera to my WiFi and using the IP-adress it got on the network (found it by checking the DHCP lease on my router, its hostname is IRCAMxxx) for FTP and Telnet i could bypass having to struggle with RNDIS at all. Installed the Basic package, will use that for a while before trying out the advanced one.

Bud, you truly are a hero. <3

Psi:

--- Quote from: 556 on January 07, 2022, 03:16:54 pm ---Thank you! I'm a total dumbass and did not realize that the download package contained the proper step by step guide (yea sometimes you should open the readme.txt  |O). I was endlessly searching the forum here for the 17-point guide everyone were refering to with no luck!

--- End quote ---

You're not the only one who's done that. Not by far!
I put off buying an E4 for years because every time I tried to search through the 100's of forum post for the one with all the steps I always gave up.
I didn't want to grab any of the files until I had found the post with the steps and read through it to make sure I grabbed the right files.   :palm:

It would be a good idea if someone can add a line to the first post saying something like...
'The step by step guide and instructions can be found in the readme text file inside the zip files'

tillmoss:
Hi, I’m new.
I have FLIR E5 WiFi with 3.16.0 firmware. Can I add this mod/hack to my camera? Where I can find a guide to do this?
I found only old guides for 2.x firmware. Is the same for 3.16.0?
I’m interested in advanced mod

In the conf.cfg I see this line “ .caps.config.name text "app E4" ” Must I change E4 to E5?


Thanks to all

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version