Products > Thermal Imaging

Uni-t UTi260B

<< < (41/62) > >>

aydd:

--- Quote from: aydd on December 28, 2022, 11:14:08 pm ---I saw vertical screen pictures interference on the screen 2 times. It's not a permanent situation. it may be normal to see this on a comprehensive thermal camera for the first time Unknown.. no photo sorry. I'll take it again

--- End quote ---

https://www.veed.io/view/8c477bae-a2be-44bc-b181-4f4959ff6890?sharingWidget=true&panel=share

this video please check.

but i got this. more parasites occurred than that. is this normal?

katzenhai2:

--- Quote from: aydd on December 30, 2022, 12:03:50 am ---https://www.veed.io/view/8c477bae-a2be-44bc-b181-4f4959ff6890?sharingWidget=true&

--- End quote ---
Good question. I don't own a Uni-T device. Maybe one of the other owners can compare it with their device.
This doesn't happen with my devices (from HIKMICRO). But could theoretically be normal and related to the used screen in the devices.  :-//

teddychn:

--- Quote from: Algoma on November 22, 2022, 03:20:08 pm ---Picked up one of these from the Nov11 sales, so far it has been excellent the first few times I've used it. Only trouble is that it doesn't charge on a USB-C charger. I've had to use the included USB-C to USB-A cable to charge it at fixed 5V

This one has a Firmware v1.2.10

After a full charge, I did hit a bug with all temperatures reading 0'C and center spot -275'C. All other general operations seemed normal. A reboot didn't fix. Then did factory reset from the menus with no change. Restarted and it froze up at EN/CN language selection on boot. Rebooted yet again and it now seems to have returned to normal operation.

--- End quote ---

I can't charge my UTi-260A with type-C charger as well. And it's firmware version was 1.0.20 too.

The manual claims turning on/off continuously can damage the device. I'm curious about the science in it. So we can only take it carefully for now.

aydd:

--- Quote from: teddychn on December 30, 2022, 06:13:32 am ---
--- Quote from: Algoma on November 22, 2022, 03:20:08 pm ---Picked up one of these from the Nov11 sales, so far it has been excellent the first few times I've used it. Only trouble is that it doesn't charge on a USB-C charger. I've had to use the included USB-C to USB-A cable to charge it at fixed 5V

This one has a Firmware v1.2.10

After a full charge, I did hit a bug with all temperatures reading 0'C and center spot -275'C. All other general operations seemed normal. A reboot didn't fix. Then did factory reset from the menus with no change. Restarted and it froze up at EN/CN language selection on boot. Rebooted yet again and it now seems to have returned to normal operation.

--- End quote ---

I can't charge my UTi-260A with type-C charger as well. And it's firmware version was 1.0.20 too.

The manual claims turning on/off continuously can damage the device. I'm curious about the science in it. So we can only take it carefully for now.

--- End quote ---

lcd screen problem

I noticed that it is affected by cell phone signals. If the device is nearby when the phone rings, these interferences exist :)

teddychn:

--- Quote from: aydd on January 03, 2023, 08:25:06 pm ---
lcd screen problem

I noticed that it is affected by cell phone signals. If the device is nearby when the phone rings, these interferences exist :)

--- End quote ---

I set my cell phone and UTI260A side by side. Then made a call to my  phone. Seemed nothing happened.

Navigation

[0] Message Index

[#] Next page

[*] Previous page