What is the purpose of the circuit? That doesn't look like a voltage regulator to me, it looks like a push on, push off switch? A bit of an odd way of doing one. Or does it vary the voltage by running the mosfet in linear mode?
I think this is the basic idea:
Falstad simulation
(Attachment Link)
Press the UP button to increase the load current and the DOWN button to decrease it.
The scope at the bottom shows the load current.
And here is the schematic from the first video (at around 1:27 in the video):
(Attachment Link)
Doesn't look like the MOSFET is being used correctly -- at the very least the source and drain need to be swapped if I'm not mistaken.
Thank you for the simulation exactly that's what I want, however I did swap the drain and source still didn't get any changes
Thank you for the simulation exactly that's what I want, however I did swap the drain and source still didn't get any changes
Are you sure you didn't blow your MOSFET?
I wouldn't be too surprised if it has failed short because IRFZ44 isn't really meant to operate in linear mode and that LED you are showing likely draws some non-trivial current. Also, in the second photo with the 3 LEDs in series I don't seem to see any current limiting resistor. You are running this from 2 Li-ion cells (a really really really BAD idea unless you enjoy some impromptu fireworks), so a lot of current is to be had for anything that could want to blow ...
You are also likely blasting the gate of that transistor with ESD. Granted, it is a relatively chunky device with a zener protected gate (assuming it is a genuine IRFZ44 and not some eBay/AliExpress special/fake) but it isn't going to survive that forever.
If it doesn't work, you need to start to debug. Throwing hands up in the air isn't a valid debugging technique.
- Use a current limited power supply, not a battery that can supply hundreds of amps (and blow up in your face doing so!) in case of an accidental short! If you don't have one, put at least a current limiting resistor in series!
- Put a current limiting resistor in series with the LED - that MOSFET has a very low resistance when it is fully conducting. That is likely to blow your LEDs
- Measure the voltage on the MOSFET gate - if it is constantly above the threshold voltage (about 3-4V for IRFZ44), it will be conducting and the LED will be on. If that is so, you may have a shorted switch, for example
- Remove the capacitor and verify that you can actually both turn the MOSFET on by putting positive voltage on the gate and turn it off by grounding it. If you can't, you have either wired something wrong (e.g. the MOSFET is reversed and the body diode is conducting) or the transistor is shorted.
Thank you pointing out.
If you have read, I mentioned I have tried so many other mosfets same number so I'm confident they work.
I'm using Riden PSU of course I'm aware not to blow anything up!
Thank you pointing out.
If you have read, I mentioned I have tried so many other mosfets same number so I'm confident they work.QuoteThat wasn't clear from your messages. I don't see you mentioning that anywhere above.U may need to read again! Changed all elements!!!I'm using Riden PSU of course I'm aware not to blow anything up!You can clearly see the alligator clip though.QuoteI have assumed that first photo you have posted (which clearly shows what looks like two 18650 cells) was yours.That shows u haven't read anything then That's taken from the youtube link provided!!QuoteIf you want meaningful help it would be very helpful to post both the schematic and pictures of your actual setup, not something that is almost completely unrelated to what you have in front of you.Again if U go through the whole thing you can clearly see I have PICTUREand SCHEMATICas well!
U may need to read again! Changed all elements!!!
I'm trying to make this adjustable voltage regulator with IRFZ44 push button, however it stopped working.
this worked only once I've changed all elements but no luck at all.
You can clearly see the alligator clip though.
QuoteI have assumed that first photo you have posted (which clearly shows what looks like two 18650 cells) was yours.That shows u haven't read anything then That's taken from the youtube link provided!!
U may need to read again! Changed all elements!!!
You wrote:QuoteI'm trying to make this adjustable voltage regulator with IRFZ44 push button, however it stopped working.
this worked only once I've changed all elements but no luck at all.
I guess my English is really not good enough to recognize how this implies that you have actually verified that your MOSFET isn't blown (or destroyed all of them).You can clearly see the alligator clip though.
So you show a picture that has a battery and second picture that isn't showing any power supply but alligator clips - and we are supposed to figure out what is that clip connected to somehow and that it isn't the battery?
Right, makes sense ...QuoteI have assumed that first photo you have posted (which clearly shows what looks like two 18650 cells) was yours.That shows u haven't read anything then That's taken from the youtube link provided!!
I didn't watch the videos. If you can't formulate your question clearly without us having to resort to piecing together what your problem actually is (like what Ledtester did) and watching unrelated youtube videos, maybe the problem is not on our side?
Maybe less attitude and more thought before hitting the keyboard would be advisable.