Lecroy DDA-5005 - Firmware / HDD Image

• Lecroy DDA-5005 - Firmware / HDD Image
  Posted by sixtimesseven on 20 Nov, 2019 22:57
• Hi
  
  I have a Lecroy DDA-5005 with a faulty hard drive. Unfortunatly I did not find a image of the drive so far. Since the device is obsolete I doubt that Lecroy will hand over the image, but maybe someone has cloned one?
  
  Thank you very much!
• #1 Reply
  Posted by DaJMasta on 21 Nov, 2019 03:14
• You shouldn't really need it.  Get a new drive, install windows and take it from there.  Just recovered a WP7300 in that manner, and it's documented somewhat in the thread in the test equipment section.  Through the service menu it's possible to recal as well, though you want a separate partition for it (I think the defaults are FIRMWARE on C and USERDATA on D).
  
  Basically it's:
  Install XP
  Install chipset drivers
  Install XStream
  Install XStream drivers
  Install touch screen drivers
• #2 Reply
  Posted by sixtimesseven on 26 Nov, 2019 14:46
• Quote from: DaJMasta on 21 Nov, 2019 03:14

  You shouldn't really need it.  Get a new drive, install windows and take it from there.  Just recovered a WP7300 in that manner, and it's documented somewhat in the thread in the test equipment section.  Through the service menu it's possible to recal as well, though you want a separate partition for it (I think the defaults are FIRMWARE on C and USERDATA on D).
  
  Basically it's:
  Install XP
  Install chipset drivers
  Install XStream
  Install XStream drivers
  Install touch screen drivers
  

  
  Well I had a look in the thread but I cannot seem to find where to actually get the x-stream firmware and drivers?
  I haven't found anything on the Lecroy website as well. Do I have to ask them directly and hope they hand it out or is there a mirror somewhere?
  
  Thanks
  
• #3 Reply
  Posted by LateLesley on 27 Nov, 2019 22:10
• Could you get the software from here??
  
  https://teledynelecroy.com/support/softwaredownload/documents.aspx?sc=17
  
  (choose Disk Drive Analyzers (DDA 3xxx, 5xxx) )
  
  
• #4 Reply
  Posted by sixtimesseven on 28 Nov, 2019 09:41
• Ah... thank you. I seem to have overlooked that part 
• #5 Reply
  Posted by spilihps on 28 Nov, 2019 19:03
• Is that also a XP Embedded install?
  
  I was trying to get hold of all the software components to make a "rescue"disk for my LeCroy 454 incase of harddrive failure. I have everything but the xp embedded media.
  LeCroy wont send that.
• #6 Reply
  Posted by sixtimesseven on 28 Nov, 2019 19:08
• Quote from: spilihps on 28 Nov, 2019 19:03

  Is that also a XP Embedded install?
  
  I was trying to get hold of all the software components to make a "rescue"disk for my LeCroy 454 incase of harddrive failure. I have everything but the xp embedded media.
  LeCroy wont send that.
  

  
  I don't know about the 454 but the 7000 and 8000 series use the normal desktop win2000 or winXP afaik(?)
• #7 Reply
  Posted by spilihps on 28 Nov, 2019 19:24
• Ah i see! Does it have the key-sticker in it and all then? Then you are in luck!
• #8 Reply
  Posted by sixtimesseven on 28 Nov, 2019 19:46
• Even if you have no key sticker - win2k and xp and win7 keys are floating around in the www pretty freely these days. The good old days before online key validation
• #9 Reply
  Posted by coromonadalix on 29 Nov, 2019 02:11
• Yep  tons of keys are available 
  
  Hacked  cough cough  an Xp installation recently  with an dll injection ...  wga removal   cough cough  loll
• #10 Reply
  Posted by sixtimesseven on 07 Dec, 2019 01:38
• I'm trying to get the dam thing to work but the best I got so far is a kind of demo mode 
  
  https://www.eevblog.com/forum/testgear/upgrading-mainboard-in-lecroy-dda-3000-(aka-wavepro-7300a)/msg2818252/#msg2818252
  
  Maybe someone from this thread has a idea?