Did you check that the Noiseblocker is specified for equivalent air flow and (more important) pressure ?
UrJTAG 0.10 #1869
Copyright (C) 2002, 2003 ETC s.r.o.
Copyright (C) 2007, 2008, 2009 Kolja Waschk and the respective authors
UrJTAG is free software, covered by the GNU General Public License, and you are
welcome to change it and/or distribute copies of it under certain conditions.
There is absolutely no warranty for UrJTAG.
jtag.c:518 main() Warning: UrJTAG may damage your hardware!
Type "quit" to exit, "help" for help.
jtag> cable jtagkey interface=0
Connected to libftd2xx driver.
jtag> frequency 5000000
Setting TCK frequency to 5000000 Hz
jtag> detect
IR length: 5
Chain length: 1
Device Id: 00100010011111100100000011001011 (0x227E40CB)
Manufacturer: Analog Devices (0x0CB)
Part(0): BF526 (0x27E4)
Stepping: 2
Filename: c:\program files (x86)\urjtag\data/analog/bf527/bf527
bfin-part-bfin.c:155 bfin_wait_ready() Warning: untested cable or frequency, set
wait_clocks to 21
jtag> initbus bf526_ezkit
jtag> readmem 0x00000000 0x001FFFFF output.dmp
Error: blackfin.c:87 bfin_bus_area() out of bounds: reading external memory not
supported
jtag>
Did you check that the Noiseblocker is specified for equivalent air flow and (more important) pressure ?
Air flow is a bit lower. I will measure the temperature inside after 1 hour of operating and share it here. I do not expect troubles, as the room temperature is max 25 degrees Celsius.
@PepeK
I was attempting to use urJTAG; as far as I know, urJTAG only runs with the one command window and the commands are different to (gdb).
I am doing it wrong? Anybody?
@PepeK
I was attempting to use urJTAG; as far as I know, urJTAG only runs with the one command window and the commands are different to (gdb).
I am doing it wrong? Anybody?
@Slappy_g
Your post gave me some hope as I have been trying to get the Olimex ARM-USB-OCD working on Windows 7 32 bit.
Following your post I swapped out the Olimax drivers for the WinUSB ones using Zadig, now I'm seeing a warning message about TD0 being stuck at 0.
Did you encounter this in your travels?
Do you know if its possible to test communication with the Olimex ARM-USB-OCD device without attaching it to a TAG connector?
I had that problem when I installed the 'H' version on Win 7 64 bit, and it all came down to the drivers
I stumbled across these drivers (H version) and after installing the drivers and following Slappy_g's excellent write up am now fully up and running
If you try and run the program NOT connected to the JTAG header it will come up with an error mmy WIN essage, but not the TDO stuck one.
Good luck, you will get there eventually!!
Andy
Just a point of advice for anyone looking to do this. Don't waste your time or money with the cheap chinese USB Blaster clones... I had an Olimex adapter overnighted and it is currently dumping the memory without issue (Running Ubuntu 14.04LTS 64bit). I'll report back after getting it dumped and trying to do the key generation whether I run into any problems, but so far it has been FAR less painless then mucking about with that chinese crap I bought the first time.
AND... COMPLETE SUCCESS!! Took about 30 minutes or so to dump the memory and then used rigup on the resulting memory dump. Few seconds later I had my key. Now I've got an optioned MSO2202A!
Just a point of advice for anyone looking to do this. Don't waste your time or money with the cheap chinese USB Blaster clones... I had an Olimex adapter overnighted and it is currently dumping the memory without issue (Running Ubuntu 14.04LTS 64bit). I'll report back after getting it dumped and trying to do the key generation whether I run into any problems, but so far it has been FAR less painless then mucking about with that chinese crap I bought the first time.
AND... COMPLETE SUCCESS!! Took about 30 minutes or so to dump the memory and then used rigup on the resulting memory dump. Few seconds later I had my key. Now I've got an optioned MSO2202A!
I tried Ubuntu, Windows, gdb, and urJTAG.
Just a point of advice for anyone looking to do this. Don't waste your time or money with the cheap chinese USB Blaster clones... I had an Olimex adapter overnighted and it is currently dumping the memory without issue (Running Ubuntu 14.04LTS 64bit).
Are you using the blackfin toolchain?.If so, which one?
I have an old IBM laptop that has Ubuntu 32 bit installed.
Hi guys,
First of all, congratulations for your tremendous work, very impressive!
I'm preparing the future hacking of the MSO2072A I intend to order and started to download everything to comply with the Slappy_g procedure. Problem: Avast anti-virus software is detecting a malware (win32:EVo-gen) in the Blackfin Toolchain for windows .exe. Is it a false alert and can I in your opinion download safely this file (which is not so easy with Avast running...)?
Thx in advance,
Denis
Might be getting somewhere but I'm stuck again...
After much frigging around, I finally managed to get my Bus Blaster running. Now it's connected to the MSO2072A and talking to the BF526.
The problem appears to be that the readmem command always tells me that it can't dump the contents of external memory, it seems not to matter what range I type in for the second value, I tried 0x0000FFFF, the response is still exactly the same as the dump below. I'm trying to follow Slappy_g's instructions on page 3 of this topic but I always get the response below. What are the missing steps 4,5 & 12? Any ideas?
Hi guys,
First of all, congratulations for your tremendous work, very impressive!
I'm preparing the future hacking of the MSO2072A I intend to order and started to download everything to comply with the Slappy_g procedure. Problem: Avast anti-virus software is detecting a malware (win32:EVo-gen) in the Blackfin Toolchain for windows .exe. Is it a false alert and can I in your opinion download safely this file (which is not so easy with Avast running...)?
Thx in advance,
Denis
@Slappy_g
Your post gave me some hope as I have been trying to get the Olimex ARM-USB-OCD working on Windows 7 32 bit.
Following your post I swapped out the Olimax drivers for the WinUSB ones using Zadig, now I'm seeing a warning message about TD0 being stuck at 0.
Did you encounter this in your travels?
Do you know if its possible to test communication with the Olimex ARM-USB-OCD device without attaching it to a TAG connector?
I had that problem when I installed the 'H' version on Win 7 64 bit, and it all came down to the drivers
I stumbled across these drivers (H version) and after installing the drivers and following Slappy_g's excellent write up am now fully up and running
If you try and run the program NOT connected to the JTAG header it will come up with an error message, but not the TDO stuck one.
Good luck, you will get there eventually!!
Andy