Each time I start the application as a regular user.
Anyways it is good that in my C:\ThermoVision_JoeC_V1.4.0.0RelFE the program works much better.
I am under Windows 10, 64 bit.
As for the histogram. Up to now I have thought that if I adjust the range manually I sent a
commands to the camera and camera adjusts its temperature range.
Based on your explanation about "everything", "only area" it seems it is not the case.
Can you please shed some light on this?
Despite my efforts to use Zadig as a open driver the images I get are not as good as what I get immediately by i3Systems USB driver.
Does i3Systems USB driver deals with the dead pixels itself?
I don't see my big bad pixel with the i3Systems USB.
From the things I have tried I was not able to understand/make it working:
- Deleting of the MinMAx measurement
- Time Plotter, what it is about?
I will play with visual blending using my web camera as a visual camera later.
Can you explain how well I have to align the view of the thermo and visual camera?
QuoteEach time I start the application as a regular user.
Anyways it is good that in my C:\ThermoVision_JoeC_V1.4.0.0RelFE the program works much better.
I am under Windows 10, 64 bit.
Thanks. But what do you mean with "works much better"?
As for the histogram. Up to now I have thought that if I adjust the range manually I sent a
commands to the camera and camera adjusts its temperature range.
Based on your explanation about "everything", "only area" it seems it is not the case.
Can you please shed some light on this?
Thank you Joe!
I will test some more later.
However once I got very strange result while I was doing the two point calibration.
The whole program got killed and the ThermoVision_JoeC.exe disappeared.
This was happening before with the old version too.
It is not a show stopper but it is strange.
The dead map behaves strange too. Once I got very good map but few minutes later it was bad see attachments.
Hi Joe,
Each time I start the application as a regular user.
I am under Windows 10, 64 bit.
Anyways it is good that in my C:\ThermoVision_JoeC_V1.4.0.0RelFE the program works much better.
Can you also use the i3 driver under windows 10 64 bit. ThermoVision works only with the zadig driver on Win10 x64
Is there a way to remember the settings in ThermoVision ? Everytime I reopen Thermovision I have to put all the settings back.
Joe-c, When I was doing calibration the whole Termovison got killed (from the task manager). I didn't get any error message. In addition my Termovision shortcut lose its icon so I have checked and ThermoVision_JoeC.exe was not there anymore where it was suppose to be.
I got this few time up to now and making the ThermoVision_JoeC.exe read only didn't solve it.
It may be something to my machine, let see if anyone else get this.
Hi Jeroen13,
Let me try to offload Joe-c and answer, Joe-c please correct me if I said something wrong.QuoteCan you also use the i3 driver under windows 10 64 bit. ThermoVision works only with the zadig driver on Win10 x64I tested with both i3 drivers and zadig and ThermoVision is working on my Windows 10 64bit.
Quote from: dpenev on Today at 08:36:38 AM
Joe-c, When I was doing calibration the whole Termovison got killed (from the task manager). I didn't get any error message. In addition my Termovision shortcut lose its icon so I have checked and ThermoVision_JoeC.exe was not there anymore where it was suppose to be.
I got this few time up to now and making the ThermoVision_JoeC.exe read only didn't solve it.
It may be something to my machine, let see if anyone else get this.
thank you for telling me.
after some tries I found a issue using the tab "Mapcal" from Calibration window. Did you use that?
If yes, this function works only if the TE was connected with the Zadig Driver, and the Camera Switch on top will stand on "Thermal Expert Q1" and not "Seek Thermal".
The "Create new GO-Maps" does the same (just more automatic).
And for the 2Point calibration, just use from "2 Point Cal." tab the blue box... Start calibration... get Low, get Hi... the results was below...Pass or Fail.
If not, please tell me what you have done to get this crash.
Did you use the Zadig or the i3 DLL Way?
What was the last Button you pressed.
Hi Jeroen13,
Joe-C has two versions of his software. In the full version there are some i3 dlls.
Check if you have i3system_USB_DLL_V2_1.dll and i3system_TE_dll.dll in your version
and if not copy from the full version or from the i3 SDK/software.
I believe I also copied exiftool.exe. Not sure how important it is
Regards
Dimitar
How did you manage that, Thermovision gives the following error with the internal driver: i3system_USB_DLL_V2_1.dll not loaded (0x8007007E)
Regarding the saving, I mounted the camera above my motorcontroller project and I want to keep it there for some periode. But every time I restart the program I have to redo all the markers and the color palette. It would be nice if it could be saved in a project file or something.
But the situation I get "ThermoVision_JoeC.exe" 'auto disappearing' I was getting pretty often.
I have not analyzed but it seems it was happening after I close ThermoVision_JoeC and restart the PC
It typically happend like that. I decide to test in the morning and I see that the shorcut icon is blank and I get no ThermoVision_JoeC.exe. I unpack the software again and next morning similar situation.
It is interesting that with the latest software and (probably with my "latest way of working")
I get no more from this issue.
Would it also be possible to enlarge the markers when you save an image, they are very small if interpolation is used.
Also some strange distortion appears in the new version. Measurement also differ.
... so I can explain it more later if you want.
I would be very grateful for futher information
Joe-C is a manual temp range possible ?
Now in the Version 1.4.x you have the option: "read only TempMap" and this was enabled by default. Just uncheck this Option, and you get the image from Byte Map
I think we should tell i3 about this issue...
If you want to compare the 2 Image frames, you should uncheck Menu->Options->"Use Settings from File".
How did you captured the CSV files?
I've put your csv file in my app for converting i3 csv files...