-
Complete MOBILE board assembly setup up for grabs:
https://www.ebay.com/itm/374464695348
You could take it on vacation. -
I'm actually impressed.
-
Quote
SMT Line
Neoden-style paste printer
Inspection conveyors (qty 2)
Samsung CP40LV with tape, tray, vibe, and 3d printed cut tape feeders
No-name 8 zone mesh belt oven (3-phase, configured for single 3x 60A)
SlimKIC II thermal profiler
AgnosPCB Inspection station with raspberry pi 4
Dishwasher with DI water filter kit
?? 3D printed parts?
Raspberry Pi? -
?? 3D printed parts?
Raspberry Pi?
That inspection system is just a photo capture software that then does A/B comparison in the cloud with a few extra features.
Raspberry Pi is more than fine for that.
Yea it is not a high-end bit of tech but the software works for a lot of people.
I don't use it myself but quite a few people I communicate/work with do use it commercially.
3D printing parts for pick and place is also fine. Some stuff does not feed well so ends up going onto a tray-like feeder setup for cut tape.
This is not a multimillion-dollar setup. Got to lower your expectations somewhat 😂 -
Pfft may not ship to Australia
-
Yes, 3D printing or CNC routing custom trays for pick and place is very common regardless of the vintage of the machine.?? 3D printed parts?
3D printing parts for pick and place is also fine. Some stuff does not feed well so ends up going onto a tray-like feeder setup for cut tape. -
Wow! Going for $6300 so far, that's a GOOD deal on the Samsung CP40 machine alone!
Jon -
Wow! Going for $6300 so far, that's a GOOD deal on the Samsung CP40 machine alone!
Jon
I have a Samsung CP60L machine with ~50 8mm feeders in chicago I'll sell for $6300 if anyone interested. -
Where were you 2 years ago??!!?? When I started on my quest to upgrade my P&P machine, I saw a CP45 at a local auction and was very impressed. But, the bidding got a bit high. Then, I bought a Quad QSA30A from an auction in Austin TX. That is a Samsung CP30 with Quad electronic feeders and Quad flying alignment cameras. It has some serious software quirks, but now I have got it pretty much figured out.Wow! Going for $6300 so far, that's a GOOD deal on the Samsung CP40 machine alone!
Jon
I have a Samsung CP60L machine with ~50 8mm feeders in chicago I'll sell for $6300 if anyone interested.
But, I ended up spending WAY more than I had anticipated on this venture - about $7500 or so - to get the feeders and repair parts for the machine.
The Quad feeders are a bit fiddly to thread and unload, but seem to work pretty well. I had a Philips/Yamaha CSM84 before, and the feeders were VERY easy to load and unload, but had really weak cover tape pulling and that was a CONSTANT issue. I did get a look at the Samsung feeders used with the CP45, they looked "OK", kind of similar to the Philips/Yamaha ones. how do your feeders deal with assorted tape quality?
The Quad electronic feeders can be programmed for component pitch and pickup position with buttons. The old Philips/Yamaha feeders only did 4 mm advance on the 8 and 12mm tapes, but the 16mm and wider could be set for 4-8-12-16 mm advance by moving the air cylinder mount. I kind of liked that you could SEE what the part pitch was set to without installinng the feeder on the machine.
One of the things that I really hate about the Quad feeders is that the reel hanger is a separate piece from the feeder. I liked that on almost all other machines, the reel is hung from the feeder so it comes off the machine as one unit.
Jon
-
Complete MOBILE board assembly setup up for grabs:
But you have to paint a text on the trailer saying: "This is not a meth lab!"
https://www.ebay.com/itm/374464695348
You could take it on vacation.