Subject: USB led
Camera: ThermalExpert Q1
Lens: 13mm f/1.0
Camera mods: additional ZnSe 50mm lens
Theater rehearsal...
ThermalExpert TE-Q1+, 19mm F1
Camera: Flir E4 (doctored)
Subject: Cat
Subject: JBC soldering iron handpiece
Subject: FT1000MP MarkV amateur transceiver
Subject: Cat with different palettes (ironbow&gray rainbow)
Camera: Seek Thermal on windows 10 (Thermovision 1.7.1)
Lens: Seek fixed
Image manipulation: crop, resize, noise
Camera mods: External protection, tablet pivot mount
Camera: ThermalExpert Q1
Lens: 13mm f/1.0
Playing with rainbow palette...
Car engine:
Old house and mountains:
Chips on the pcb:
Landscape:
Oh, man, I've wanted to do thermography on insects! I wish we could see how the colors on that butterfly correspond to its visible colors, to know how much of this is metabolically-generated heat and how much is absorption from sunlight.
Subject: Daughter in sandbox
Camera: ThermalExpert Q1
Lens: 6.8mm f/1.3
Image manipulation: Sharpen, Interpolation x2
Camera mods: None
Subject: Toyota Prius II, after drive with flat tyre
Camera: ThermalExpert Q1
Lens: 6.8mm f/1.3
Image manipulation: Sharpen, Interpolation x2
Camera mods: None
Subject: Hand trauma
Camera: FlirOne on Galaxy s5 (thermal camera +)
Lens: FlirOne default
Image manipulation:
Camera mods:
Took a tumble at work and smacked my hand good. Trauma seen on right hand, middle knuckle.
Ugh....make it home ok?
Do you mean i was able to repair it? Yes. a tiny hole... could be filled.
i am quite happy that a guy on a bicycle at the crossroad told me, one side on back was flat.
i drove for round about 30 minutes. Drive feeling was normal, but with windows down and radio off i was able to hear a difference.
Subject: Back Tyres after drive (right was flat, both with same scale)
Camera: ThermalExpert Q1
Lens: 6.8mm f/1.3
Image manipulation: None
Camera mods: None
Very interesting tenp difference!
A couple for me, Twin Otter before and after a flight...
TE Q1
Subject: various subjects
Camera:flirone on Galaxy s5(thermal camera+)
Lens: flirone
Image manipulation: cropping
Camera mods: None
Subject: Fake skull with neopixels inside
Camera: seek thermal on windows 10 tablet(thermovision)
Lens: seek default
Image manipulation: None
Camera mods: None
Subject: baby and a teacup
Camera: seek thermal on windows 10 tablet(thermovision)
Lens: seek default
Image manipulation: None
Camera mods: None
I like the stiched panorama a lot.
Almost strange that this is not board support of the FLIR software..
I attached two images made with the CAT S60 phone. ( not mine :-( )
1st is how the guys make fun to all who did not join for drinks.
2nd is my 250 quad in hoover flight. Front and Back props had different pitch, surprisingly this did not make a significant difference in temp of the motors or ESCs.
So the FLIR ONE iOS application allows for panoramic stiching and it appears to use the native iOS stiching method, however, without MSX blending enabled I have been unable to successfully stitch a thermal-only image.
Floor heating using a Flir One G2 iOS.
I also have this video of a board with a short circuit. Two transistors had a bad footprint. Causing a short.
This is what I show people when they ask
why I bought this.
People often ask me if i3 T.E. Q1 is good for PCB inspection.
I can only recommend it.
And since it has manual focus you don't need any additional ZnSe lens to get really close:
The subject is router board approx 15x10cm (4" x 6").
Camera: ThermalExpert Q1
Lens: 13mm f/1.0
People often ask me if i3 T.E. Q1 is good for PCB inspection.
I can only recommend it.
Me too
Subject: PC inside
Camera: ThermalExpert Q1
Lens: 6.8mm f/1.3
Image manipulation: Sharpen and Interpolationx2
Camera mods: None