« previous next »
Pages: [1]   Go Down

Author Topic: RIGOL DG1022 PROBLEM. help me  (Read 9893 times)

0 Members and 1 Guest are viewing this topic.

Offline hugos31Topic starter

  • Regular Contributor
  • *
  • Posts: 52
RIGOL DG1022 PROBLEM. help me
« on: May 25, 2014, 10:20:21 pm »
hello friends. accidentally; 24vdc introduced in CH1. currently; (channel 1).  not emit signal. only sale-15v dc  ..,,,,,,,,,,,,I keep track of the output circuit (channel 1) I found chip output signal (8-pin smd) with aluminum heatsink, id code cleared (scraped),,,, Please i need  code? for reeplazar
« Last Edit: May 25, 2014, 10:34:46 pm by hugos31 »
Logged
 

Offline hugos31Topic starter

  • Regular Contributor
  • *
  • Posts: 52
Re: RIGOL DG1022 PROBLEM.
« Reply #1 on: May 25, 2014, 10:21:22 pm »
 
« Last Edit: May 25, 2014, 10:27:31 pm by hugos31 »
Logged
 

Offline c4757p

  • Super Contributor
  • ***
  • Posts: 7799
  • Country: us
  • adieu
Re: RIGOL DG1022 PROBLEM.
« Reply #2 on: May 25, 2014, 10:24:45 pm »
We know what the front panel looks like - take a picture of the circuit around the chip!

It's probably just a high output current, somewhat high speed, high slew rate op amp. Check how it's connected. You might be able to substitute without knowing the part number.
Logged
No longer active here - try the IRC channel if you just can't be without me :)
 

Offline hugos31Topic starter

  • Regular Contributor
  • *
  • Posts: 52
Re: RIGOL DG1022 PROBLEM.
« Reply #3 on: May 25, 2014, 10:29:32 pm »
     id code cleared (scraped),,,,   test:  +15v  and ; -15v
« Last Edit: May 25, 2014, 10:39:40 pm by hugos31 »
Logged
 

Offline c4757p

  • Super Contributor
  • ***
  • Posts: 7799
  • Country: us
  • adieu
Re: RIGOL DG1022 PROBLEM.
« Reply #4 on: May 25, 2014, 10:35:25 pm »
Yeah, I'm pretty sure that's just an op amp. You're looking for something in the neighborhood of an LM7171, but with a thermal pad on the bottom.

Double-check that it's actually failed, though. Put it back in circuit, leave off the heat sink, set to a large output amplitude but do not terminate the output (the goal is to have zero current draw - nothing through the attenuators, as there would be at small amplitude, and nothing out the BNC - in which case it shouldn't need the sink), at low frequency. Probe the inputs and see if it behaves like an op amp.
« Last Edit: May 25, 2014, 10:37:16 pm by c4757p »
Logged
No longer active here - try the IRC channel if you just can't be without me :)
 

Offline hugos31Topic starter

  • Regular Contributor
  • *
  • Posts: 52
Re: RIGOL DG1022 PROBLEM. help me
« Reply #5 on: May 25, 2014, 10:37:58 pm »
  :-+ .  ok  I test  lm7171
Logged
 

Offline c4757p

  • Super Contributor
  • ***
  • Posts: 7799
  • Country: us
  • adieu
Re: RIGOL DG1022 PROBLEM. help me
« Reply #6 on: May 25, 2014, 10:39:32 pm »
No, please don't actually use an LM7171 - I said to find something with a thermal pad. That's just a bit too much heat for a 7171 (which is not available in a high power package).
Logged
No longer active here - try the IRC channel if you just can't be without me :)
 

Offline hugos31Topic starter

  • Regular Contributor
  • *
  • Posts: 52
Re: RIGOL DG1022 PROBLEM. help me
« Reply #7 on: May 25, 2014, 11:21:57 pm »
Logged
 

Offline kc9qvl

  • Regular Contributor
  • *
  • Posts: 149
  • Country: us
Re: RIGOL DG1022 PROBLEM. help me
« Reply #8 on: May 25, 2014, 11:41:52 pm »
OPA541  ???.  Please review the datasheet you posted.
Logged
 

Offline hugos31Topic starter

  • Regular Contributor
  • *
  • Posts: 52
Re: RIGOL DG1022 PROBLEM. help me
« Reply #9 on: May 25, 2014, 11:59:59 pm »
OPA551  https://www.futurlec.com/Linear/OPA552UA.shtml   :-//   +- 30v  is problema,,,,,,,,,,,,,can be   opa454........http://www.ti.com/lit/ds/symlink/opa454.pdf
« Last Edit: May 26, 2014, 12:25:58 am by hugos31 »
Logged
 

Offline kc9qvl

  • Regular Contributor
  • *
  • Posts: 149
  • Country: us
Re: RIGOL DG1022 PROBLEM. help me
« Reply #10 on: May 26, 2014, 12:34:57 am »
Compare the slew rate and gain bandwidth of the opa541 or 454 to the lm7172. The opa541 is not even the correct package.


Have you tested the opamp yet?
« Last Edit: May 26, 2014, 12:38:09 am by kc9qvl »
Logged
 

Offline hugos31Topic starter

  • Regular Contributor
  • *
  • Posts: 52
Re: RIGOL DG1022 PROBLEM. help me
« Reply #11 on: August 12, 2014, 10:48:47 am »
?  :-//
Logged
 

Offline rf-loop

  • Super Contributor
  • ***
  • Posts: 4105
  • Country: fi
  • Born in Finland with DLL21 in hand
Re: RIGOL DG1022 PROBLEM. help me
« Reply #12 on: August 12, 2014, 01:09:25 pm »
Quote from: hugos31 on August 12, 2014, 10:48:47 am
?  :-//

How difficult is is ask from Rigol? They perhaps have today some kind of customer care and service help?

« Last Edit: August 12, 2014, 01:15:56 pm by rf-loop »
Logged
I drive a LEC (low el. consumption) BEV car. Smoke exhaust pipes - go to museum. In Finland quite all electric power is made using nuclear, wind, solar and water.

Wises must compel the mad barbarians to stop their crimes against humanity. Where have the wises gone?
 

Offline slowolitus

  • Newbie
  • Posts: 4
  • Country: de
Re: RIGOL DG1022 PROBLEM. help me
« Reply #13 on: May 29, 2018, 03:16:43 pm »
THS3095 is the original IC
Logged
 
The following users thanked this post: bingo600, mcinque, tivoi

Offline Gandalf_Sr

  • Super Contributor
  • ***
  • Posts: 1729
  • Country: us
Re: RIGOL DG1022 PROBLEM. help me
« Reply #14 on: May 31, 2018, 10:22:24 am »
I wonder if hugos31 has reeplazared the OpAmp yet.
Logged
If at first you don't succeed, get a bigger hammer
 

Offline azemati

  • Contributor
  • Posts: 25
  • Country: ae
Re: RIGOL DG1022 PROBLEM. help me
« Reply #15 on: February 15, 2020, 08:25:50 am »
Hello everybody
There is an inductor in output section of DG1022, it has been crashed, is anyone know how the value is?
https://imgur.com/gallery/DzgQTzB
« Last Edit: February 15, 2020, 08:57:39 am by azemati »
Logged
 

Offline Dacke

  • Regular Contributor
  • *
  • Posts: 83
  • Country: us
Re: RIGOL DG1022 PROBLEM. help me
« Reply #16 on: February 15, 2020, 12:58:25 pm »
Quote from: azemati on February 15, 2020, 08:25:50 am
Hello everybody
There is an inductor in output section of DG1022, it has been crashed, is anyone know how the value is?
https://imgur.com/gallery/DzgQTzB

It's a common mode choke and the exact replacement part number is ACM4532-901-2P.   A while back,  I blew the same choke in mine as well.  Since it was difficult to find that exact one at the time,  I used a close replacement from Digikey  -  https://www.digikey.com/product-detail/en/wurth-electronics-inc/744235601/732-4221-1-ND/3672769  -  It has been working fine ever since.
Logged
 

Offline azemati

  • Contributor
  • Posts: 25
  • Country: ae
Re: RIGOL DG1022 PROBLEM. help me
« Reply #17 on: February 16, 2020, 06:43:10 pm »
My friend,
appreciate 🙏
Logged
 
Pages: [1]   Go Up
« previous next »

Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf

 


EEVblog Main Site EEVblog on Youtube EEVblog on Twitter EEVblog on Facebook EEVblog on Odysee