I got my ds2202a-s today,
4) my hardware version is 1.2.2.0.2, but other A models have 1.0.2.0.2?, is that also due to the Signalgen?
These are stopped displays, In run mode the varying trigger scanning causes the sampling to collect a series of sample along the sin display and if not a sin wave(step function) the DSO will create a sin wave overshoot.
Note : At 2.5 samples/ cycle the frequency will be accurate but Vpp is NOT.
AS EV says very few points
I think it is due to the overlap of many waveforms slightly different each time, and the wave intensity processing. Like the persistence effect.
Note: Test now with average acquisition mode and only 2 averages.
I'm unable to infer from that screenshot what is surprising to you.Why do you think that there is nothing unusual?
I got my ds2202a-s today,Where did you buy a S2000A-S version? Didn't think they were released yet. Not listed at online distributors like http://rigolna.com and http://batronix.com
Edit: they are listed at http://www.tequipment.net/rigol/series_ds2000a-series/ but without prices.
What's the price difference between the S and non-S models?4) my hardware version is 1.2.2.0.2, but other A models have 1.0.2.0.2?, is that also due to the Signalgen?Most likely.
I can enter it in the formula line of course but the "Apply" button stays grayed out as long as "log(...)" appears in the formula. The status of the button usually changes from grey to white when a correct formular has been entered. Any idea?
I can enter it in the formula line of course but the "Apply" button stays grayed out as long as "log(...)" appears in the formula. The status of the button usually changes from grey to white when a correct formular has been entered. Any idea?
Have you downgraded and tried the v.01.01.00.02 FW? It's likely a bug - and so would be good to know the extent of it.
not yet. Maybe one with v.01.01.00.02 on his system can try it out (Math -> Operate -> Advanced ->Expressions)?
Everything seems to work but not the logarithm function.
I am not able to use Log(CH1) or anything else using "log()" (even "log(10)" is not working).
I can enter it in the formula line of course but the "Apply" button stays grayed out as long as "log(...)" appears in the formula.
Everything seems to work but not the logarithm function.
I am not able to use Log(CH1) or anything else using "log()" (even "log(10)" is not working).
I can enter it in the formula line of course but the "Apply" button stays grayed out as long as "log(...)" appears in the formula.Tested it on my DS2072A and yes, "Apply" grayed out while log() is in formula even if syntax is correct.
Device: DS2072A converted to DS2202A, HW: 2.0 (1.0.2.0.2), SW: 00.02.01.00.03.
Thanks for your enthusiasm - but you're running the same FW as us, which has already been tested. We're looking to see if anyone with v.01 FW can test it.
Have downgraded to 00.01.01.00.02 again.
Bug with Log() dissapeared.
While you are reporting bugs, not that I can say this is a bug, when you first power on the unit all lights light up except the CH1 for some reason. If they are come on as a function test at power up, shouldn't CH1 also light too?
While you are reporting bugs, not that I can say this is a bug, when you first power on the unit all lights light up except the CH1 for some reason. If they are come on as a function test at power up, shouldn't CH1 also light too?
Please does DS2000 or DS2000A with latest firmware have cursors in XY mode?
That looks like tracking mode. I meant a feature like this.
Have downgraded to 00.01.01.00.02 again.
Bug with Log() dissapeared.
Have downgraded to 00.01.01.00.02 again.
Bug with Log() dissapeared.Thank you. I already passed this bug to Rigol and they verified it and said it will be passed to the engineers. However: Marmad you should still pass it over to Drieg as it will not be a mistake to report it through two different channels = chances for a correction are higher.