What did you buy today? Post your latest purchase!

[Specmaster]

Stick a trailer behind it and it could also become a boat transporter, bargain

[neo]

Stick a trailer behind it and it could also become a boat transporter, bargain

Not currently, it don't run and is roached. Besides i think that if i tried to tow a trailer with it the rear bumper might come off. As it is the front bumper is in a bad way i don't need two bad bumpers. 

Just a note, even though my birthday isn't for 6 months this was a birthday present. 
EDIT: Another note, this is my first car.

[beanflying]

Barring a further act of god, because this was an act of god to begin with, i bought the biggest boat anchor yet...

a '56 Chevy Bel Air Sports Coupe 

Not sure if owning Vintage cars or wooden boats is worse but your TEA budget is toast either way 

"Used" to own a wooden boat 

[neo]

Barring a further act of god, because this was an act of god to begin with, i bought the biggest boat anchor yet...

a '56 Chevy Bel Air Sports Coupe 

Not sure if owning Vintage cars or wooden boats is worse but your TEA budget is toast either way 

"Used" to own a wooden boat 

TEA ain't gonna die that easy, it may slow down or it may not. Entirely dependent on how happy with beans i am. 

In all seriousness i estimate once i sink six times what i paid for it into it i'll have the thing not only beautiful again but ready for the next 70 years... give or take some modifications vroom vroom

[URI]

My HP 6114 precision power supply arrived today.   

I told the seller to pad the device thick and sturdy to all sides -and he did!   
The outer cardbox was damaged on one side (I could put my hand in..) but the padding and some extra cardboxes saved it from also being damaged.

The 6114A has one flaw: It doesn't put out the voltage dialed in even though the voltage and current regulation seem to be working basically. And it has 50mV ripple on the output.
I put it on my repair queue and will start with it right away.   

[Specmaster]

Barring a further act of god, because this was an act of god to begin with, i bought the biggest boat anchor yet...

a '56 Chevy Bel Air Sports Coupe 

Not sure if owning Vintage cars or wooden boats is worse but your TEA budget is toast either way 

"Used" to own a wooden boat 

TEA ain't gonna die that easy, it may slow down or it may not. Entirely dependent on how happy with beans i am. 

In all seriousness i estimate once i sink six times what i paid for it into it i'll have the thing not only beautiful again but ready for the next 70 years... give or take some modifications vroom vroom

Once that's done it will be useful for TEA collecting purposes as well. If at all possible I prefer to collect my purchases in person. Stops the couriers playing soccer with them. [emoji23]

[neo]

Barring a further act of god, because this was an act of god to begin with, i bought the biggest boat anchor yet...

a '56 Chevy Bel Air Sports Coupe 

Not sure if owning Vintage cars or wooden boats is worse but your TEA budget is toast either way 

"Used" to own a wooden boat 

TEA ain't gonna die that easy, it may slow down or it may not. Entirely dependent on how happy with beans i am. 

In all seriousness i estimate once i sink six times what i paid for it into it i'll have the thing not only beautiful again but ready for the next 70 years... give or take some modifications vroom vroom

Once that's done it will be useful for TEA collecting purposes as well. If at all possible I prefer to collect my purchases in person. Stops the couriers playing soccer with them. [emoji23]

Not many things for sale in Missouri, sadly. 

[Inverted18650]

Had these made so I can tinker with a few ADC's I pulled from a "scrap". JLC sent me a nice SMD stencil as well. I have plenty so if you want one PM me.

edit: also started the K228 PCB on EasyEda. Anyone can check it out. I'll order the boards tomorrow and it usually takes a week to get here.

[gamalot]

New package from Digikey.

Capacitors for my Keithley 2001, two fans for 2001 and 3706, a relay to control my 3D printer, and a Nuvoton board. 

[PTR_1275]

My HP 6114 precision power supply arrived today.   

I told the seller to pad the device thick and sturdy to all sides -and he did!   
The outer cardbox was damaged on one side (I could put my hand in..) but the padding and some extra cardboxes saved it from also being damaged.

The 6114A has one flaw: It doesn't put out the voltage dialed in even though the voltage and current regulation seem to be working basically. And it has 50mV ripple on the output.
I put it on my repair queue and will start with it right away.   

Are the links on the back terminal strip there connecting the sense terminals?

[bitseeker]

edit: also started the K228 PCB on EasyEda. Anyone can check it out. I'll order the boards tomorrow and it usually takes a week to get here.

Looks good so far, all the way down to the silkscreened lethal voltage warning. Just the remaining bottom traces and then good to go. You mentioned you're going to have them made by JLC. I've been seeing them mentioned a lot lately. Looking forward to seeing their output.

Have you located a similar enough strain-relief clamp? I scoured Digi-Key and Mouser for a while, but didn't succeed, yet.

[ChrisLX200]

Bought a couple more spools of PETG 3D printer filament, one was a standard 1Kg size (blue) the other a 2.5Kg spool (black) which offered a big saving compared to a 1Kg spool. I should have expected it but the physical size of the heavy spool took me a little by surprise! There was no way it would have been mountable on the printer had I not modified it to use external spools, the spool rollers I made sit on a shelf above the printer.

Home made spool rollers


One big spool of filament




Edit: A cool idea I just had - one of the problems with many filaments is they are hygroscopic and need to be kept dry, they are transported in a plastic bag with dessicant inside. Of course, as soon as you take the spool out the bag it will start to deteriorate unless you take steps to prevent it (construct a dry box for example). With the spool rollers I figured I could just put the roller inside a large sealable bag, with dessicant, and the filament then pokes out through a tiny hole. It can be used this way and will stay dry. Seems to work fine!

[Terry01]

I don't have a 3D printer but understand the concept and that's a neat idea. Well spotted! 

[BravoV]

Few plumbing stuffs ... 

Also my 1st N type things.

[URI]

My HP 6114 precision power supply arrived today.   

I told the seller to pad the device thick and sturdy to all sides -and he did!   
The outer cardbox was damaged on one side (I could put my hand in..) but the padding and some extra cardboxes saved it from also being damaged.

The 6114A has one flaw: It doesn't put out the voltage dialed in even though the voltage and current regulation seem to be working basically. And it has 50mV ripple on the output.
I put it on my repair queue and will start with it right away.   

Are the links on the back terminal strip there connecting the sense terminals?

Yes, all links for normal operation are there.
I must admit, I thought of a fault like that in the beginning, too. 
But it wasn't: there are the original HP ones all in place. 

I found the (main) fault yesterday evening after my post:
It's a completely dead (one could think of Monty Pythons dead parrot here..  ) electrolytic capacitor in one of two rails for the control board A2.

Description here:
https://www.eevblog.com/forum/repair/hp-6114a-repair-(fault-regulation-seems-to-work-voltage-low-output-ripple)/

[edgelog]

The Quick 861DE. Almost the same unit as the Quick 861DW that Rossmann and Dave tested, but with more power, 1200W vs 1000W. It also delivers 200 L/min vs 120 L/min for the DW version. And, on top of that, it's slightly cheaper. Got it for 235 pounds UK ex VAT and ex shipping from kaisertech.co.uk.

[frozenfrogz]

The Quick 861DE.

That’s the one I have been drooling over for quite some time. One day it will replace my Aoyue int906C. One day...

[Terry01]

A 50 ml bottle of Topnik TK83 flux!  4 & 1/2 quids worth!! 

[djos]

I just ordered a brand new Pi 3 B+ and a case, from RS, to replace my WorkShop Pi Computer - it should be a nice upgrade from my old Model B v1.2.





also bought a bunch of various project parts too.

[TheSteve]

A box of goodies.

[tautech]

A box of goodies.

OOOHHH, nice find !

[HecticZA]

Bought a Magnum 2005 soldering station.

Also bought an Uni-t UT61E last month.
Both items probably won't rate that well against the more popular models, but both are a huge upgrade from what I had and I'm very happy with both.

Will now save for a Micro soldering iron for my soldering station, hot air station and I hope to get a variable power supply as well.

First of all I will have to buy some sort of scope. Due to Diabetes my eyesight is pretty bad.

Sent from my SM-N950F using Tapatalk

[0xPIT]

Bought an ES121 screwdriver. Loving it already <3

[kripton2035]

bought a cetus 3d printer. UK stocks are pretty tight so duno at all when it may arrive to me !

[VK5RC]

A box of goodies.

Christmas has come early!