What did you buy today? Post your latest purchase!

[Oldtestgear]

I have been busy buying up even more test gear in the last couple of weeks. Not what I could honestly describe as " a score" as I paid  a fair price.

Not pictured are a Datron 4910, 3x Fluke 732A, plus a couple of high quality resistor standards by Welwyn but all included in my latest attempt to complete a home cal lab.
If anyone has information or manuals for the Datron 4901/4902S/4903 I would be grateful for any information about this antique setup. My plan is to upgrade my calibration equipment & sell whatever is surplus to get some of my money back before the next opportunity to spend comes along.  I hope that this will keep me happy for a long time but I suppose it all depends on what I find next.

Cheers

Phil

[armandine2]

arrived today, a 'pb' < 18-hours from online order:
an RS-135 4-20mA Loop Calibrator & Thermometer (description from Instructional Manual)

aesthetically not exactly a looker and non-calibrated - but so is the 121GW I've just hooked it up to, they are at least both in agreement.

[armandine2]

Something of an odd couple?

[armandine2]

couple made sensible with a wall port - the RS-135 is measure only for temperature

[RAPo]

A wavetek 2002A

[vk6zgo]

A wavetek 2002A
(Attachment Link)

Waaahh!! I want one!

I've been looking for them on eBay for years, but they are fairly rare.
We used to use them back in the day, when we ran out of RS SWOB Polyskops to take on maintenance runs.

The Polyskop was the "preferred option" & to be fair, is a bit more "user friendly", plus has that BIG screen, but a 'scope & a 2002A don't stretch your arms as much!

[jasonRF]

I just picked up a Picoscope 5244B on epay.  It is a 2-channel, 200 MHz scope with variable 8-16 bit resolution, 512 MB of memory and a built-in 20 MHz AWG.  Dave did a teardown of a model in this series (5443B) a bunch of years ago at a trade show.  I got it for $450 with the nice Picotech 250 MHz probes, which I think is a fair price since the retail was $1975 and the new version (5244D) goes for $2315.   However, the seller accepted my offer so quickly it makes me wonder if I could have gotten it for an unfairly low price!

In any case, it is quite the upgrade from the pico 2204a that has been my only scope for the past handful of years. 

[mnementh]

YALBOA:



mnem

[chickenHeadKnob]

I just picked up a Picoscope 5244B on epay.  It is a 2-channel, 200 MHz scope with variable 8-16 bit resolution, 512 MB of memory and a built-in 20 MHz AWG.  Dave did a teardown of a model in this series (5443B) a bunch of years ago at a trade show.  I got it for $450 with the nice Picotech 250 MHz probes, which I think is a fair price since the retail was $1975 and the new version (5244D) goes for $2315.   However, the seller accepted my offer so quickly it makes me wonder if I could have gotten it for an unfairly low price!

In any case, it is quite the upgrade from the pico 2204a that has been my only scope for the past handful of years.

You snagged a real bargain, don't second guess it. That is if it is in undamaged  working order.
me jelly

[jonpaul]

Tektronix 7L5 Spectrum Analyzer plug-in with OPT 25 tracking generator excellent condition but months to get payment, packaging  and shipping negotiations...finally hand carry on 11 hrs flights

Loading  in 7603 and 7904 Tektronix mainframes, the scopes needed astigmatism and geometry trim on Z axis PCB, for a bright, clear, focused and aligned display. Unearthed my old 7L12 as well

The 7L5 had A few flaky connections, after contact cleaning, in CAL, dated circa 1980!

Pix of both scopes and Spectrum Analyzers, with CAL Signal and HP 8640A with wideband FM modulation.

your thoughts?

[jasonRF]

I just picked up a Picoscope 5244B on epay.  It is a 2-channel, 200 MHz scope with variable 8-16 bit resolution, 512 MB of memory and a built-in 20 MHz AWG.  Dave did a teardown of a model in this series (5443B) a bunch of years ago at a trade show.  I got it for $450 with the nice Picotech 250 MHz probes, which I think is a fair price since the retail was $1975 and the new version (5244D) goes for $2315.   However, the seller accepted my offer so quickly it makes me wonder if I could have gotten it for an unfairly low price!

In any case, it is quite the upgrade from the pico 2204a that has been my only scope for the past handful of years.

You snagged a real bargain, don't second guess it. That is if it is in undamaged  working order.
me jelly

I know you are right.  And it works great - used tinySA as source and bandwidth is 200 MHz as advertised, high-resolution modes show great detail, signal generator is really nice,  etc.   The cosmetic blemish I was expecting based on the ebay photo turned out to be a piece of scotch tape on the front panel that just peeled off!  I am very happy with it. 

But My neurosis has included a bad case of the doubters disease for as long as I can remember….

Cheers!

Jason

[MegaVolt]

If anyone has information or manuals for the Datron 4901/4902S/4903 I would be grateful for any information about this antique setup.

This is a unique set. I envy you very much.

Here is everything that is on 4902:

[RAPo]

Picked up a second hand Hioki clamp on probe Model 9008

[mclute0]

I needed some new speakers for by my test bench and I came across some sales on Newark(Farnell) and I bought two sets of these Bluetooth ceiling speakers for $10.37usd (was $122.00usd) per pair.

For that price I am not expecting much, but they came today and I am unboxing now, will update here shortly.

It includes 24v 2.5Amp 50/50hz power brick.

The instruction book says enter 0000 as the Bluetooth pin, but that doesn't work. Password printed on the back of the active speaker DOES work.

no base, but given the stated frequency response as 60hz-120khz that is no surprise, not being an enclosure right now doesn't help much me either me thinks.

with 30watts RMS per speaker there is not a lot of volume being driven by my windows10 desktop, but for ~10.00 for a pair, I am pretty happy right now.


https://www.newark.com/stellar-labs/50-16617/6-5-active-ceiling-speaker-pair/dp/25AC5146

[dl6lr]

Thought I would need a laser engraver, so I bought one. Atomstack A5pro+. This was cheap to start with. First test, laser power was a little high (from the database).

[tautech]

Thought I would need a laser engraver, so I bought one. Atomstack A5pro+. This was cheap to start with. First test, laser power was a little high (from the database).

Thread were member beanflying has some fun with his:
https://www.eevblog.com/forum/mechanical-engineering/40w-300x200mm-laser-cutter-engraver-vollerun/

[mclute0]

Next up from the UPS man today!


https://www.vevor.com/dc-stepper-motor-c_11221/vevor-nema-17-stepper-motor-83-6-oz-in-high-torque-2a-42x48-mm-for-3d-printer-p_010392030792


I bought five NEMA17 steppers from VEVOR. Includes wire stripper/cutters and electrical tape, not sure why since they have dupont connectors.

I always laugh at the stuff on that site, like the chicken plucker drill attachment and the "VEVOR Automatic Chicken Coop Door Opener Cage Closer Timer Light Sensor" and the "VEVOR Snow Melting Mat 10" x 30" Walkway No-Slip Heating Entrance Mat Waterproof 120v" but I saw these steppers and for ~$27.00usd with free shipping I decided to dive in for my next prototyping project, the "mostly 3d printed CNC"...

https://docs.v1engineering.com/mpcnc/intro/

I noted that steppers with the exact same listed specs and same part number except first two digits are 17 instead of 42 and the name is listed as Voron are available from
https://www.omc-stepperonline.com/

Also marked with CE cert labels.

[thm_w]

I bought five NEMA17 steppers from VEVOR. Includes wire stripper/cutters and electrical tape, not sure why since they have dupont connectors.

Oh it doesn't include the wire stripper, its equipped with a stripper:

【EFFORTLESS TO USE】- The stepper motor is equipped with a wire stripper commonly used by internal electricians, motor repairs, and instrument electricians to strip plastic & rubber insulated & cable core wires. Insulating rubber tape with excellent insulation performance and good adhesion to prevent leakage.

What a terrible thing to include with stepper motors. Someone out there is twisting wires together and then taping them up, making the worst connection on earth.

[beanflying]

Thought I would need a laser engraver, so I bought one. Atomstack A5pro+. This was cheap to start with. First test, laser power was a little high (from the database).

Big thing to be really careful with open Laser engraving or cutting is where the beam can go if reflected and what fumes/poisons is the material giving off. At minimum open doors and windows but far better put a proper cover over it with extraction to the outside both for your lungs and eyes.

So many MORONS with 'free' ones of theses on youtube literally blowing smoke up Bangoods ass while simultaneously sucking it into their lungs.  Play Safe 

[rdl]

I had to restart a computer today and when I did, for some reason it couldn't get a network connection. I noticed the LEDs on the switch it was plugged into were blinking in a mad, crazy pattern. I tried the usual fixes but only bypassing the switch and going directly to the router worked. I used the same port as the switch, so the router isn't part of the problem. My NAS was also plugged into the switch and to get it back I'd have to disconnect a printer. No real problem as I have only used the printer once or twice in the last year, but I decided to buy a new switch just to put things back as they were.

I got something around 10 years of use from the switch, so I didn't have any problem buying its successor. It's even cheaper.

https://www.amazon.com/gp/product/B00A128S24/



To ensure some future fun, I added the 8-port "managed" version to my order. Considering I now qualified for "free" shipping, it almost cost less than the 5-port version.

I'm thinking I should also buy some kind of back up router - just in case. Electronic stuff tends to fail at odd times for strange reasons. Last year, as far as I could tell, my cable modem died because of loud thunder.

[dl6lr]

Big thing to be really careful with open Laser engraving or cutting is where the beam can go if reflected and what fumes/poisons is the material giving off. At minimum open doors and windows but far better put a proper cover over it with extraction to the outside both for your lungs and eyes.

Used it outside for testing and probably will do so ever. Enclosure to come.
This atomar thing has no end stops    Homing will run the mechanics to the ends and then fail  So have to take a look if and where to attach switches. Laser reflection is greatly reduced as the head is only 2mm from the surface.

[RAPo]

Got a hioki af-105, fond memories from my youth.

[armandine2]

deleted by poster - not on topic

[mnementh]

A1 SIZE CUTTING MAT

   

https://www.amazon.com/dp/B08FM3ZP4V

Today I found this one; a 5-layer mat with a nice metric side, and with the current 20% discount it's only $26.

When it gets here in a few days I'll followup with real pics and first impressions. If you're needing a new mat, this could be a killer deal. No idea if those outside the US can find this one with similar discount. 

mnem
*scrubbing a paint sprayer*

[Ed.Kloonk]

Want.