Folks!
I just found a release document on the WEB which I machine translated to english. That document just goes up to rev. 2.31 2.32 is not included...
2016/12/8 V2.31
1, increased PCB software "Easy-PC" files into formats compatible with 11.10
2, mount complete the prompt box the next time you start automatically remove 11.11
3, manual, does not run when the nozzle down 11.11
4, increasing Visual precision adjustable bias (element coordinate deviations, element angle deviation) 11.28
5, modify 0402 needles suction bug 12.7
2016/11/5 V2.30
1, change the maximum acceleration
2, the keys function increase file editing (ESC, space, Delete)
3, delete the symbol prompt information "confirmed"
4, increasing the light switch
2016/10/8 V2.29
1, modify the file "posted" order bug
After stopping the machine needle 2, modified firing pin bug
3, scale accuracy of 0.0001
4, stack after stack, 6, 7th against (Beta2)
5, 802A disk cannot be located, set before the current bug (Beta3)
2016/10/5 V2.28
1, revised separate pin offset is not in place of the fabric stack Bug
2, open to give up other location data in the system setup parameters
3, increase the length of 16mm feed
2016/09/02 V2.27
1, modify components parameters table "description" column, do not select the same data change bug
2, depending on the camera on "Visual components" adding "Red Cross"
2016/08/20 V2.26
1. the software implemented two versions a, b, b, 802A, two versions
2. differences:
A software (1) system setup small stacks in the back behind the bar, and other parameters in the PIN offset parameter
(2) in the element information table in "stacks" column in less material behind stack options
(3) when the CSV file is loaded, a loaded b-file will report an error
2016/08/05 V2.26
1. increase the percentage of EFAC coefficient, fix x, y coordinates
2016/07/19 V2.25
1. amendments to the results did not automatically detect save bug
2016/07/09 V2.24
1. fixed limit trigger the buzzer doesn't alarm
2. the factory parameters depending on the test button to add the light source open
3. close the page when testing the nozzle automatically stopped
2016/06/27 V2.23
1. fixed stack-pin on the left offset parameter error
2016/06/07 V2.22
1. increase depending on camera "photo delay" or "camera exposure" parameter
2016/05/27 V2.21
1.IC stack sorting optimization
2016/05/04 V2.20
1.IC stack sets the current serial number can be read
2. swing PIN card
3. Add a separate needle for each stack offset
4.PCB configuration, automatically switches to manual mode and depending on the camera mode
5. change camera acquisition algorithms.
6. depending on the camera light on only when the test opens.
2016/03/21 V2.12
1. fixed two nozzles while feeding, the second device in the stack in the back angle errors
2016/02/21 V2.11
1. front material stack up to 30
2.ACC12:X10 Y7 Z15
ACC11:X7 Y6 Z12
2015/11/16 V2.10
1. the maximum acceleration
2. tray can use two suction nozzle and mounting
2015/11/12 V2.09
1. When you don't have to check the material, not in place waiting for inspection
2015/09/28 V2.08
1. fixed after the capture device, when moving to the posted position, determine the pressure, and z-axis down
2015/08/31 V2.07
1. fixed 2nd after Visual suction head, process errors of judgment
2015/08/24 V2.06
1. modify the English translation
2015/08/21 V2.05
1. fixed coordinate the IC Tray problem
2015/08/19 V2.03
1.24mm the strip width
2015/07/25 V2.02
1. fixed IC tray when Y=1, coordinates of confusion
2. fixed coordinate system parameters page camera location
3. modify LED errors
2015/05/28 V2.0
1. fixed needle drop BUG after a pause. The new version firmware.
2015/05/10 V1.25
1.IC Tray under plate increments
2015/04/29 V1.24
1. fixed IC Tray 1 sequence problem
2015/04/10 V1.23
1. fix rear stack 11~30 stack 1/2 suction nozzle only when a material problem
2015/04/07 V1.22
1. fixed load CSV file when the file because the device is empty alarm
2015/03/20 V1.21
1. increased needle fabric stack offset
2015/03/06 V1.20
1. fixed after the 2nd nozzle dump, repeat posted 1th bug
2.12MM set distance
2015/03/04 V1.19
1. fixed when the file is read, not read into the PCB configuration BUG
2015/02/27 V1.18
1. the parameters go to the coordinates from the manufacturer depending on the camera system parameters
2015/02/24 V1.17
1. can support Protues coordinates the export file
2015/02/12 V1.16
1. fixed camera manufacturers parameter coordinate automatic test BUG
2. fixed stack separate sort BUG
3. fixed read Candes coordinate export file error
4. increase can read the decimal point as a comma-file
2015/01/10 V1.15
1. fixed IC Tray data bug
2014/12/26 V1.14
1. increase the generated array functions
The position of the 2.PCB configuration increases the z-axis origin location
3. fixed the right-click menu sets the current camera position bug
2014/12/04 V1.13
1. modify the English version of the stack display error bug
2014/12/04 V1.12
1. revision of German regional data decimal points are replaced by comma bug
2014/12/02 V1.11
1. modify 0402 stack feed 2mm, needle drop coordinates error bug
2014/11/29 V1.10
1. support 802B double stack SMT machine
2. improved pre-stack functions
2014/10/30 V1.08
1. improved feature by camera device coordinates (consider MARK point transform)
2. Add a right-click menu and set the coordinates must be in a State of origin has been found
3. added support for Allegro export file
2014/10/27 V1.07
1. modify the parameter settings page, position run without prompting z is not zero-bug
2. change when the file is loaded, bottom mirrored error bug
3. remove manual run time, request the z axis at zero
2014/10/24 V1.06
1. modify the selected row appears error bug
2014/10/24 V1.05
1. revision of PCB configuration-5th Board Gets the camera position bug
2. change SN number display bug
3. modify the 1th nozzle nozzle feeding, feed 2mm,2 4mm, 2 a good nozzle suction error bug
4. Add the home button icon
5. increase the version number display