K4 I don't know. The device I had was too old and didn't support that option. Just try them one after another and you'll probably find it.
Let me try clarify some things (although I don't know much about this).
The list of options extracted from FSP firmware v4.50 API.DLL is the following:Code: [Select]K5 GSM/EDGE Application GSM K5 ANALYZER FSPSpectrumAnalyzerLI
K7 FM Demodulator FM DEMODULATOR FSPSpectrumAnalyzerLI
#1
#2
K84 1xEV-DO BTS 1X EV DATA ONLY BTS FSPSpectrumAnalyzerLI
K85 1xEV-DO MS 1X EV DATA ONLY MS FSPSpectrumAnalyzerLI
K90 FSQ WLAN 802.11a WLAN FSQ-Wlan(LI)
K72 WCDMA 3GPP FDD BTS WCDMA BTS ANALYZER FSPSpectrumAnalyzerLI
K74 WCDMA HSDPA BTS WCDMA HSDPA BTS FSPSpectrumAnalyzerLI
K75 WCDMA HSDPA MS WCDMA HSDPA MS FSPSpectrumAnalyzerLI
K9 Power Meter POWER METER FSPSpectrumAnalyzerLI
K73 WCDMA 3GPP FDD MS WCDMA MS ANALYZER FSPSpectrumAnalyzerLI
K90 FSP WLAN 802.11a FSP WLAN FSP_Wlan(LI)
K90UP FSQ WLAN 802.11a,b,g WLAN UPGRADE
K76 TD-SCDMA BTS TD-SCDMA BTS ANALYZER FSPSpectrumAnalyzerLI
K77 TD-SCDMA MS TD-SCDMA MS ANALYZER FSPSpectrumAnalyzerLI
K30 Noise Figure NOISE MEASURE FSx-Noise(LI)
K82 CDMA2000 BTS CDMA2000 BTS FSPSpectrumAnalyzerLI
K83 CDMA2000 MS CDMA2000 MS FSPSpectrumAnalyzerLI
K8 Bluetooth BLUETOOTH FSPSpectrumAnalyzerLI
K40 Phase Noise Measurement PHASE NOISE MEASURE FSx-PNoise(LI)
K70 Vector Signal Analysis VECTOR SIGNAL ANALYSIS FSPSpectrumAnalyzerLI
#3
K50 Triggered Coverage Meas TRIGGERED COVERAGE MEAS
K51 Synchronized Stepped Sweep SYNCHRONIZED FREQ LISTS
%d days remaining trial period TRIAL PERIOD 180 HRS
K0 %d days remaining trial period TRIAL PERIOD 2000 HRS
K91 FSQ WLAN 802.11a,b,g WLAN ABG FSQ-WlanExtension(LI)
#5 FREQ LIMIT 31 GHZ
B%s Frequency Extension FREQ NO LIMIT
K92 FSQ 802.16 FSQ 802_16 FSQ-Wman(LI)
K52 Transducer Set REG_TP
K53 FFT Scan FFT SCAN
K901 %d days remaining trial period TRIAL PERIOD 2500 HRS
K902 %d days remaining trial period TRIAL PERIOD 3000 HRS
K92UP FSQ 802.16e FSQ 802_16 UPGRADE
K93 FSQ 802.16e FSQ 802_16E FSQ-WmanExtension(LI)
K903 %d days remaining trial period TRIAL PERIOD 3500 HRS
K904 %d days remaining trial period TRIAL PERIOD 4000 HRS
K100 LTE FDD Downlink LTE FDD DOWNLINK FSx-LTE FSx-LTE(LI)
K101 LTE FDD Uplink LTE FDD UPLINK FSx-LTE FSx-LTE(LI)
B29 Frequency Extension 20Hz FREQ EXT 20HZ
K15 Avionics Demodulator AVIONICS DEMODULATOR FSPSpectrumAnalyzerLI
K91N FSQ WLAN 802.11n WLAN 802 11N UPGRADE FSQ-Wlan80211n(LI)
K94 FSQ 802.16e MIMO FSQ 802_16 Mimo UPGRADE FSQ-WmanMimo(LI)
K102 LTE Downlink MIMO LTE DOWNLINK MIMO FSx-LTE FSx-LTE(LI)
K103 LTE Uplink MIMO LTE UPLINK MIMO FSx-LTE FSx-LTE(LI)
K96 OFDM-VSA OFDM-VSA
K74+ WCDMA HSPA+ BTS WCDMA HSPA+ BTS
#4
K400 RFEX-F Launcher RFEX-F
K17 EX IQ Box EX IQBOX FSx-ExIqBox(LI)
K110 TETRA 2 TETRA2 FSQ-Tetra2(LI)
K10 GSM/EDGE/EDGE Evolution GSM/EDGE ANALYZER FSx-Gsm(LI)
K73+ WCDMA HSPA+ MS WCDMA HSPA+ MS
K104 LTE TDD Downlink LTE TDD DOWNLINK FSx-LTE(LI)
K105 LTE TDD Uplink LTE TDD UPLINK FSx-LTE(LI)
K106 LTE TDD/FDD Upgrade LTE TDD/FDD UPGRADE
K5UP GSM K5 Upgrade to K10 GSM K5 ANALYZER UPGRADE FSx-Gsm(LI)
K150 Support for User Calibration USER CAL SUPPORT
They are ordered according to the seeds table (used in the prog to generate licenses).
Also, in that .DLL we can extract a more complete seed (uint32) table than the one used in the original prog (post #7). I attach it below.
Those that are using the program should add the new seeds because they may be needed to enable other Options.
The FSH Option names can be extracted from the FSH firmware's API.DLL. If anyone sends me a current FSH API.DLL I might extract the complete list of Options.
When adding the Option seeds you should also make them TRUE so that all possibilities are calculated.
Hey Guys,
I have a ZVR, SN is 835068/005. and I found the SW sn \R_S\INSTR\INI\OPTOIN.INI
Is't anyone know how to decode it?
--------------------------------------------------------
4056071223; EMBED DEEMBED
0436723430; TIME DOMAIN
1234299954; CONVERTER 4 CHAN
--------------------------------------------------------
sn: 835068.005 id: 00 option key: 1542267991 desc: feat_0
sn: 835068.005 id: 01 option key: 2797899109 desc: feat_1
sn: 835068.005 id: 02 option key: 2277388772 desc: feat_2
sn: 835068.005 id: 03 option key: 2328386865 desc: feat_3
sn: 835068.005 id: 04 option key: 0302356071 desc: feat_4
sn: 835068.005 id: 05 option key: 3024766616 desc: feat_5
sn: 835068.005 id: 06 option key: 4252011699 desc: feat_6
sn: 835068.005 id: 07 option key: 4056071223 desc: TIME DOMAIN, B2, Time Domain Measurements
sn: 835068.005 id: 08 option key: 0436723430 desc: CONVERTER 4 CHAN, C4C, 4 Channel Converter
sn: 835068.005 id: 09 option key: 1234299954 desc: EMBED DEEMBED, K9, Virtual Embedding Networks
sn: 835068.005 id: 10 option key: 0493488890 desc: feat_A
Hi tv84,
I attached a API.DLL form a ZVR. could you decode the option from it?
Hi tv84,
I attached a API.DLL form a ZVR. could you decode the option from it?
I don't think so. Do you have examples of options for that equipment?
Hey Guys,
I have a ZVR, SN is 835068/005. and I found the SW sn \R_S\INSTR\INI\OPTOIN.INI
Is't anyone know how to decode it?
--------------------------------------------------------
4056071223; EMBED DEEMBED
0436723430; TIME DOMAIN
1234299954; CONVERTER 4 CHAN
--------------------------------------------------------
maybe
feat_0 = 'HARMONIC MEAS', 'B3', 'Harmonic Measurements'
feat_1 = 'MIXER MEAS', 'B4', 'Mixer Measurements'
feat_2 = 'NONLINEAR MEAS', 'B5', 'Nonlinear Measurements'
feat_3 = 'REF MIXER PORTS', 'B6', 'Reference Mixer Ports'
feat_4 = 'POWER CALIBRATION', 'B7', 'Power Calibration'
feat_5 = '4 PORT MEAS', 'B99', '4-Port Measurements'
feat_6 = 'QUARTZ MEAS', 'BXX', 'Quartz Measurements'
This is an old public algorithm.
test Feat_2+, if all OK - test b3-b4 too,
in newer devices - these numbers(0 or 1) used for demo.
now r&s used new long key.
many know how to create new too,
but no one wants to share it to public ))Code: [Select]sn: 835068.005 id: 00 option key: 1542267991 desc: feat_0
sn: 835068.005 id: 01 option key: 2797899109 desc: feat_1
sn: 835068.005 id: 02 option key: 2277388772 desc: feat_2
sn: 835068.005 id: 03 option key: 2328386865 desc: feat_3
sn: 835068.005 id: 04 option key: 0302356071 desc: feat_4
sn: 835068.005 id: 05 option key: 3024766616 desc: feat_5
sn: 835068.005 id: 06 option key: 4252011699 desc: feat_6
sn: 835068.005 id: 07 option key: 4056071223 desc: TIME DOMAIN, B2, Time Domain Measurements
sn: 835068.005 id: 08 option key: 0436723430 desc: CONVERTER 4 CHAN, C4C, 4 Channel Converter
sn: 835068.005 id: 09 option key: 1234299954 desc: EMBED DEEMBED, K9, Virtual Embedding Networks
sn: 835068.005 id: 10 option key: 0493488890 desc: feat_A
I have a R&S ZVB8 2 port Vector Network Analyzer, but I can't see any options file (SWOPT.DAT or similar). Under 'Info', no files are loaded that indicate which file it could be.
I could really use the ZVAB-K2 Time Domain option - does anyone have any good suggestions? The serial-number is 6-digits.
To be honest, I can't even see where I would load a valid software option key.
I have a R&S ZVB8 2 port Vector Network Analyzer, but I can't see any options file (SWOPT.DAT or similar). Under 'Info', no files are loaded that indicate which file it could be.
I could really use the ZVAB-K2 Time Domain option - does anyone have any good suggestions? The serial-number is 6-digits.
To be honest, I can't even see where I would load a valid software option key.
Hi Jacod,
I don't have the ZVB yet. I download the firmware form RS and than extract all files.
there is a DLL file "OptionKeyServices.dll", I guess this Dll is work for the option key.
for the SW option key, you should search *option*.* or *opt*.* in D disk. in my ZVR, it's "Option.ini".
and check the serial-number on "info" hard key manu.
I have a R&S ZVB8 2 port Vector Network Analyzer, but I can't see any options file (SWOPT.DAT or similar). Under 'Info', no files are loaded that indicate which file it could be.
I could really use the ZVAB-K2 Time Domain option - does anyone have any good suggestions? The serial-number is 6-digits.
To be honest, I can't even see where I would load a valid software option key.
Have tried all the options with variations mentioned in these pages to no avail.
I've been reading through this thread - anyone know the situation with the more modern series of R&S equipment (e.g. RTE / RTO series of scopes).
R&S seem to base their designs on a couple of platforms, with occasional "mid-life" upgrades of the underlying HW (and OS - usually embedded Windows of some kind). The RTE / RTO platform is common and Win7 / Win10 embedded. with license key support for temporary and time limited licenses as well as portable licenses and license de-activation.
Anyone confirm whether these can be played with?
Hello,
did anybody try to enable options for signal generators like SMIQ, SME?
I did try different combinations on a SME which expects a 6-digit activation key without luck. The serial number is same as the others xxxxxx/xxx.
Any hints are highly appreciated.
BR,
Dimce