The 'USB' Option at the Top changes the USB Baudrate.
Option 'Interface' selects the interface for internal connector (OFF/USB, WIFI, TTL, RS485)
and 'Baudrate' set the speed for it.
For WIFI interface, option 'Baudrate' is ignored and always used 115200
Both of these interfaces can work simultaneously.
That is, if you select the interface (WIFI, TTL, RS485), USB will not be disabled.
In that case, I'd like to make a couple suggestions for improved clarity:
Change "USB" to "Front Panel USB"
or "Front USB" (depending on the number of characters available)
Change the option "USB" to "OFF"
In that case, I'd like to make a couple suggestions for improved clarity:
Change "USB" to "Front Panel USB"
or "Front USB" (depending on the number of characters available)what for?
there is only one single USB...
Change the option "USB" to "OFF"From beginning it was OFF...
But other people ask me to change it to USB (if USB is enabled)...
May be just rename that options to
TTL Interface
TTL Baudrate
?
How do you restore the default firmware if you have an issue?
...Is the voltage ramp a built-in feature that can be changed in the firmware?
Hi UniSoft can you please open a new thread for this model and make these PDF's and the 5-day discount the 1st post?
Do you remember post #538 when senior member BravoV asked for this? Your efforts are AMAZING but mixing models on one forum thread is making things confusing and time consuming for members to get help for the original model 6006
Hi UniSoft can you please open a new thread for this model and make these PDF's and the 5-day discount the 1st post?
Do you remember post #538 when senior member BravoV asked for this? Your efforts are AMAZING but mixing models on one forum thread is making things confusing and time consuming for members to get help for the original model 6006
Hi Cliff,
I've been writing a manual for the RD6006, RD6012, and RD6018 with some assistance from UniSoft ...
I plan on posting an (almost) complete document soon - Probably Wed, not sure yet.
There are a few things I want to complete first, but it won't be 100% by then.
When I do, I'm going to put it in it's own thread, kind of a Fresh Start from the current Firmware Revision with everything I could parse out of this thread. I think this will help with what you're looking for.
I don't know if UniSoft would be posting new firmware changes in that thread - I haven't asked - But I hope to be able to keep the document up to date with the community's help.
Standby LED: Rename "Default" to "Pulsating"
Language: Rename "German" to "Deutsche"; "French" to "Francais"
MEM Hint Setting
Pressing a different Memory location button before the timeout value will display the values at the new location.
Can the old behavior:
"... a second click during this time will apply these settings."
Be put back in as an option?
ScrsaverBright Setting
Suggestion: Can the Brightness settings be made to line up with the 'Backlight' values?
Status Info Setting
Request: Can we have an option to choose what info gets cycled in 'Default' setting?
ie, I don't care about the raw ADC values, but may want Temperature and Battery Voltage to cycle through.
Can the firmware versions be unified into the same 'version' number, so only the Model number is different for each update?
Hi UniSoft can you please open a new thread for this model and make these PDF's and the 5-day discount the 1st post?
Language: Rename "German" to "Deutsche"; "French" to "Francais"OK
Standby LED: Rename "Default" to "Pulsating"
Language: Rename "German" to "Deutsche"; "French" to "Francais"OK
Language: Rename "German" to "Deutsche"; "French" to "Francais"OKThe translation of "German" to "Deutsche" is faulty, it should be "Deutsch"
@sunkmail: Please verify.
MEM Hint Setting
Pressing a different Memory location button before the timeout value will display the values at the new location.regress...
will fixCan the old behavior:
"... a second click during this time will apply these settings."
Be put back in as an option?The "Mem Hint" option controls this itself.
If enabled, the settings will be applied by double click.
(Only due to regress, does not work now)
Why need make a separate option for this?
ScrsaverBright Setting
Suggestion: Can the Brightness settings be made to line up with the 'Backlight' values?values of 'ScrsaverBright' are equal to values of 'Backlight'
OFF = Complete turn off the backlight.
0 = ‘backlight’ level 0
1 = ‘backlight’ level 1
2 = ‘backlight’ level 2
3 = ‘backlight’ level 3
4 = ‘backlight’ level 4
5 is not available (= ‘backlight’ level 5) cause have to sense...
Status Info Setting
Request: Can we have an option to choose what info gets cycled in 'Default' setting?
ie, I don't care about the raw ADC values, but may want Temperature and Battery Voltage to cycle through.There is no such option now.
Can the firmware versions be unified into the same 'version' number, so only the Model number is different for each update?I use the same version as a stock firmware...
ie: RD60062_V1.34.1m
where:
RD60062 - is a model
V1.34 - version, equal to the stock firmware
1 - subversion of custom firmware
m - if there is a letter then this is a beta (release will be V1.34.2)
Original software check the version for updates, so I have to keep the same version as a stock firmware
Standby LED: Rename "Default" to "Pulsating"
Language: Rename "German" to "Deutsche"; "French" to "Francais"OK
I second, and forgive me to nitpick a bit, but "Deutsch" (without the e) and "Français" (with the accent) would be best.