Recent Posts

1

Test Equipment / Re: Choosing between entry-level 12-bit DSOs

« Last post by Fungus on Today at 05:46:40 pm »

I'd like to know what the Siglent does on a real AM waveform, too.

Feed in the 220MHz signal at 500MSamples/sec. but add some AM modulation and see if it reproduces it (eg. 16MHz modulator).

2

Microcontrollers / Re: How to create custom bootloader in esp8266

« Last post by tellurium on Today at 05:45:36 pm »

Well, yeah, but then it is quite unclear what "if button is pressed, enter the programming mode" means. The description goes about a simple bootloader that either boots a firmware, whatever it is, or "enters a programming mode" - which is, I believe, a built-in ROM bootloader in the programming mode. Note that OP mentions "OTA", but there  is nothing really about OTA in the description.


OP, you do not describe your task well enough, apparently because you don't understand it well enough. You need to refine your description.

3

Test Equipment / Re: Second bench PSU, am I thinking about this correctly?

« Last post by krby on Today at 05:44:47 pm »

If you have the space you could pick up something like an Agilent 6624A for very little money on ebay.
This particular unit has four isolated channels and they were used in automated test equipment setups.
They do not have banana plug sockets and the UI isn't great (LCD is hard to read) as they were meant to go into test rigs or system use and were usually remote controlled.
They are of high build quality, but are obsolete, so many installations have taken them out of service once Agilent (Keysight) stopped servicing them. All of this makes them a great deal.
If you don't feel like having to repair it from the get go, you should probably not get the absolute cheapest. Look for good vendor ratings.

Thanks for the reply! What would the advantage be to something like the 6624A vs a new (but cheap) linear supply? I guess better accuracy, regulation and ripple than a Korad? Since I'm new at this (and likely don't know what I'd be missing) I thought 1mV-3mV ripple is great for what I have planned. I really would like to be able to control it easily without a laptop or PC attached.

4

Microcontrollers / Re: How to create custom bootloader in esp8266

« Last post by kripton2035 on Today at 05:43:04 pm »

https://randomnerdtutorials.com/esp8266-ota-updates-with-arduino-ide-over-the-air/

5

Other Equipment & Products / How does the JBC (and clones) Soldering Station Sleep Mode Work?

« Last post by Astray on Today at 05:42:45 pm »

Hello,
I'm trying to get a better understanding of the JBC and Aixun T3A/T420 cartridge type soldering stations connections and how they work to put the soldering iron into the sleep mode while it's connected to its stand.

I remember reading a post (or maybe watched a video) about it but I've been unable to find it again even after searching the forum and googling. There was a breakdown of all the connections to the handle from the stand and the main station.

What is electrically happening when the outer metal part of the handle connects to the stand? What kind of voltage, current, and/or signal is it sending back to the main station?

I would like to know this information to make it easier to modify my soldering station and out of curiosity's sake too.

Thanks!

6

Manufacturing & Assembly / Re: Advice on adding missing parts to an assembled board

« Last post by Kean on Today at 05:42:35 pm »

You could make an extra layer for a custom stencil.  Copy the paste layer and add cutouts around the componets that JLC will place so the stencil won't hit them.

Apart from the massive difficulty this could cause during additional stenciling, which will depend on which parts are placed and which areas need additional paste...

If you order such stencil from JLC, make sure to specify that they use the stencil apertures as provided, else they will typically window pane the larger cutouts.

7

Projects, Designs, and Technical Stuff / Re: Corrosion on DIP pins

« Last post by strawberry on Today at 05:42:01 pm »

wont split open but rust will get to bondwires if it continues
even solder is tarnished 

I wouldn't be surprised if the caps had leaked, and the electrolyte is the reason for the rust.

capacitors are not as corroded

8

Projects, Designs, and Technical Stuff / Re: ESR meter with extended scale.

« Last post by iet on Today at 05:41:47 pm »

As you know, the ESR of a capacitor can react to the heat of your hands. And the result may not correspond to the actual value. In addition, to obtain the most reliable result, very reliable contact between the probes and the legs of the capacitor is necessary.
Therefore, a simple device was made to install and measure the ESR of capacitors.

9

Open Source Hardware / Re: ESP32 Ethernet, Wi-Fi & Serial Gateway

« Last post by tooki on Today at 05:41:37 pm »

Looks nice!

Some questions/comments:
- choosing to use the bare ESP32 IC is a bold move, because that means you have to seek regulatory certification yourself for the radios. (One of the big advantages of using an ESP32 module is that they’re already certified worldwide.)
- why USB mini-B and not USB-C?
- what are the two different Ethernet port versions?
- the datasheet has a typo, the RTC crystal should be 32.768kHz, not 32.758kHz.

10

Beginners / Re: Photodiode output emulation

« Last post by KrudyZ on Today at 05:41:08 pm »

This depends very much on how accurate you want to model the PD behavior.
The simplest would be to use a function generator and a resistor.
This works if your PD is zero voltage biased and your circuit can work with either side of the PD being at Earth ground as that's where your function generator ground will usually be at.
You are of course missing quite a few secondary effects of the PD, such as junction capacitance and non-linear behavior if voltage develops due to the TIA not maintaining the zero bias (during transients).
The latter also affects the accuracy of the current. To minimize the effect, you should set the output voltage of the function generator as high as possible and then adjust for the desired current by picking larger resistor values (ideal current sources have infinite source resistance and infinite compliance voltage).
That being said there are many PD configurations where what I described would not work, so we would need to see your schematics.