Recent Posts

1

Microcontrollers / Re: Looking for information on TEST pin and ways to DUMP mask ROM of PIC1650 PIC16xx

« Last post by jpanhalt on Today at 09:34:56 am »

Interesting read (link #1).  Link #2 might help.  I did not g through the whole thing.

https://www.eejournal.com/article/a-history-of-early-microcontrollers-part-9-the-general-instruments-pic1650/

http://bitsavers.org/components/gi/PIC/1983_PIC_Series_Microcomputer_Data_Manual.pdf

What tools to you have to read it?

2

General Technical Chat / Re: What did you buy today? Post your latest purchase!

« Last post by tautech on Today at 09:34:38 am »

From RS
Small antistatic mat.
Antistatic gloves
25x 3W 3535 SMD LED's
HMC1118LP3D RF switches ..... any guesses what for ? 

3

EEVblog Specific / Re: EEVblog 1612 - Siglent SDS1000X HD 12 bit Oscilloscope Teardown

« Last post by shapirus on Today at 09:30:27 am »

While going frame by frame, you can see that the 2354 updates on each frame, while the 1024 usually displays a single waveform for 2 frames.

That's interesting. And we know that the SDS800X HD have crippled resolution of the displayed (but not captured/stored) waveform. I wonder if the 1000X HD does the same. And if the 800X HD has that frame rate reduction too.

That would mean they have some unfortunate bottleneck in the screen image rendering path.

4

Microcontrollers / Re: Looking for information on TEST pin and ways to DUMP mask ROM of PIC1650 PIC16xx

« Last post by woofy on Today at 09:23:21 am »

The only info on the test pin I have says "Test input not normally used".

5

Projects, Designs, and Technical Stuff / Re: role of optocoupler for biasing drain of amplifiers

« Last post by xvr on Today at 09:21:45 am »

> You said i should put a zenner diode .
did you meen in parralel to the power supply?

No. In series with R2 in my schematic

As for temperature raise, it calaculated as power, dissipated in MOSFET multiplayed by Temperature resistance (55W/C by your calculations). Power dissipation is I^2*Rdson

Graph in question shows changes of Temperature resistance via pulse characteristics.

Tja & Tjc are temperature resistancies from chip junction to ambient (this is case of bare chip in air) and for chip junction to case (this is variant of chip attached to ideal heatsink)
As you understand there is no such thing as ideal heatsink, so in later case you shoul add Temperature resistance of heatsink itself to Tjc to get real value

6

Projects, Designs, and Technical Stuff / Re: a high side load switch made from n channel and p channel mosfet working princip

« Last post by moffy on Today at 09:18:48 am »

When 'enable' is low then Q1 is 'off', and the gate of Q2 is pulled up to its source by R2 and it too is 'off'. When 'enable' is high then Q1 is 'on' and the gate of Q2 is pulled down to 0V turning Q2 'on'.

7

Jobs / Re: Contract Job - EEVblog: Making Shorts/Reels

« Last post by Exwallid on Today at 09:18:39 am »

Your post about the contract job opportunity at EEVblog is like music to my ears! It's fantastic to see opportunities like this pop up, especially in a community where talent and expertise are valued.

8

EEVblog Specific / Re: EEVblog 1612 - Siglent SDS1000X HD 12 bit Oscilloscope Teardown

« Last post by golden_labels on Today at 09:13:10 am »

While going frame by frame, you can see that the 2354 updates on each frame, while the 1024 usually displays a single waveform for 2 frames.

9

3D printing / Re: could anyone please print me a microscope Head adaptor ring

« Last post by davebb on Today at 09:09:33 am »

Today The post women had my adaptors from mendip_discovery,Thanks Again,
The Adaptors fit very well, it is a shame that the ABS one failed half way through as it is a tighter fit with the ali spacer, but the other is fine just a little bit more play but still very good, why i wanted the long size is to hold the LED Ring Light,
if i mount the ring light to the lens i can use the ABS Adaptor, i am very happy with your great work Roger,
Thanks Again,
Dave 2E0DMB

10

Beginners / Re: Quickly Triggering Sensors - need an oscilloscope? what specs? (AU)

« Last post by xvr on Today at 09:06:25 am »

Sure, if you can find one - it's obsolete by Discovery 3