GT650M and GTX660M are based on GK107 which is a Kepler generation chip. You can use the soft-straps in the BIOS to change the device ID, same as on earlier Fermi and Tesla GPUs...
FF FF FF 7F 00 00 00 00 FF FF FF 7F 00 00 00 80
which doesn't look like any bootstrap i've seen in Fermi bioses.Not sure if anyone is still following this topic, but I would like to request some help identifying R1-R4 on this card. The card is an Asus GT640-DCSL-2GD3. I have posted pictures below showing U10 and the surrounding resistors. Please let me know if you need any more information!
Thanks!
Has anybody checked if the modifying the cards removes the limit on the number of simultaneous nvenc encoding sctreams available? GeForce cards are limited to 2 simultaneous H.264 encoding streams, but Quadro/Grid cards are supposed to be able to handle more.
(Note: NVENC only exists on Kepler and Maxwell GPUs, there is no support for it on Fermi and earlier GPUs.)
Hi all,
Recently I've just bought a Asus GT640-2GD3 thinking that the PCB and resistors placement should be the same as 1GD3 but apparently it's not. I've tried to locate the R1 - R4 eg R543 resistor but I cannot find it on the board. Could you help me out here please to identify the resistors to change this to Grid K1? Thanks a million in advance. I've attached the images as well Do kindly let me know if it's not sufficient
wow, comeback to this thread after 3 years makes me feel so nostalgic! O0
I'm going to do a hardmoding with my GTX 750Ti (Quadro K2200 counterpart). Hopefully all the electrical engineer lessons and stuffs gained through the last 3 years could help me understand "this world" a bit more! But before touching it, there are a couple of "million" questions that I wish to be enlightenThanks for your help!
- Can anyone give me a full instruction (or short hints) on how to track down these strap registers?
- Did anyone here successfully mod the Maxwell generation to their quadro counterpart?
- Can anyone provide me the high res picture of the quadro K2200 pcb?
I would also like to post a BIG THANKS to everyone that has donated so far, we are at $300 with $700 remaining at the time of this post.
I plan to video the modification of the GTX690 with before and after benchmarks which will be posted on YouTube. I will also record the process of finding the hardware straps for the other GPU through deductive reasoning and simple testing that is relatively safe to the hardware. So if you want to see this, throw a little into the pool so I can get a card I can safely do this on.
Once we have all the information all figured out I will trawl through this thread and compile everything into a single post making it easy to reference.
I'm going to do a hardmoding with my GTX 750Ti (Quadro K2200 counterpart).
wow, comeback to this thread after 3 years makes me feel so nostalgic! O0
I'm going to do a hardmoding with my GTX 750Ti (Quadro K2200 counterpart). Hopefully all the electrical engineer lessons and stuffs gained through the last 3 years could help me understand "this world" a bit more! But before touching it, there are a couple of "million" questions that I wish to be enlightenThanks for your help!
- Can anyone give me a full instruction (or short hints) on how to track down these strap registers?
- Did anyone here successfully mod the Maxwell generation to their quadro counterpart?
- Can anyone provide me the high res picture of the quadro K2200 pcb?
I'll send you the picture in 2 days tops with the quadro K2200 pcb . I have a video card Asus GTX750Ti and I want to mod it to make a Quadro K2200 so be able to GPU Passthrought on my ESXi 5.5 server. without that mod, my VM Windows 7 not stop showing error 43.
My pc specs: ESXi 5.5 u2 on Core i5 4690, 8GB ram, ASRock Z97 Extreme6 with dual NIC support(onboard intel and realtek both gigabit) with Asus GTX750Ti https://www.asus.com/Graphics-Cards/GTX750TIOC2GD5/
LE: Pictures suck, i told the guy who sell this video card to make a better picture with the upper-right corner where the screw seems to have attached something, that's where resistors seems to be sticked on pcb; I'll post that picture when i get it. I'll post a picture soon with my gtx750ti also
Later later Edit: I uploaded more pictures..still the pictures are not good. I will get to a client who has this card in his workstation and i'll make some good quality pictures.