Nice bench japasetelagoas. What brand is that screwdriver set? Are they good quality? looks neat.
Hey bookaboo, that screwdriver set is made by a Brazilian company called Worker.
It was fairly cheap compared to the big brands down here, 100 BRL,roughly 30 USD.
The only "downside" that I can mention is that the print faded quite easily on the tools that I use the most as you can see on the image below. The Torx one and the big flathead that I barely use have their labels basically intact.
By the way, in case you wanna check out their catalog this is the link:
http://www.ferragensnegrao.com.br/catalogo/ferramentas-manuais/#pag_111
Japa, some of the more expensive stuff does the same. I have 4 Bondhus ball head torx drivers in my work toolbag. I use them regularly and the writing is worn off all of them. They work just as good without the writing as with and I paid as much for my 4 as you did for your whole set. Worn writing shows that they are being used and not looked at.
My excuse for a LAB
:
http://imgur.com/a/Uc6dk/allAlmost all drawers are full of parts/tools/whatever, also I have additional 3 overhead storage spaces for rest of my stuff....
Let's play a game: Find a scope in all this mess, usually to find something in this mess takes 2-6 hours
Let's play a game: Find a scope in all this mess, usually to find something in this mess takes 2-6 hours
Looks a lot like a Hantek DSO5000P series model:
Let's play a game: Find a scope in all this mess, usually to find something in this mess takes 2-6 hours
Looks a lot like a Hantek DSO5000P series model:
DSO5000B series toy with crashing horizontal zoom on deep memory
and a bit of how you are doing trigger
, need to replace with Rigol DS1000Z or Agilent DSOX2004A, can't decide which one to buy, rigol is 5.6 times cheaper...
The lastest configuration of my workspace in the basement. The shelf unit is made from veneered particle board which I acquired as cheap remnants. The edges are finished with solid pine and painted. Three of the bays are standard rack width.
The lastest configuration of my workspace in the basement. The shelf unit is made from veneered particle board which I acquired as cheap remnants. The edges are finished with solid pine and painted. Three of the bays are standard rack width.
The way you did the electrical wiring is fantastic. I really like that idea.
Hanging leads from a slotted rack is great. Did you make that or is there a source for it?
What are you guys doing to store heat shrink? I can't seem to come up with a good solution. Various options:
1) reel/roll. Problem is, doesn't work well for various diameters, don't roll nice when they crease and bend, or when it gets short (end of roll).
2) boxes. Basically a box for each with a hole to dispense from. Prob here is possibility of getting tangled inside.
3) chop them up into a tacklebox bin. Problem here is possible waste or issues when you need a longer length than pre cut, plus all the up front work.
4) hang strands. Heat shrink often comes in 4ft lengths. I'm thinking kinda like the slotted rack for leads but maybe use clothespins to hold each strand?
Hanging leads from a slotted rack is great. Did you make that or is there a source for it?
What are you guys doing to store heat shrink? I can't seem to come up with a good solution. Various options:
1) reel/roll. Problem is, doesn't work well for various diameters, don't roll nice when they crease and bend, or when it gets short (end of roll).
2) boxes. Basically a box for each with a hole to dispense from. Prob here is possibility of getting tangled inside.
3) chop them up into a tacklebox bin. Problem here is possible waste or issues when you need a longer length than pre cut, plus all the up front work.
4) hang strands. Heat shrink often comes in 4ft lengths. I'm thinking kinda like the slotted rack for leads but maybe use clothespins to hold each strand?
How about paper/carton tube that is used to carry A3 size drawings?
I'm using a bit of 3" pvc plumbing for my long stuff.
Same idea as the cardboard tube. Bit more rigid if you want to clamp it to something.
Hanging leads from a slotted rack is great. Did you make that or is there a source for it?
Looks like the OP made that one, but for an off the rack solution, there are the Pomona 1508, 4408, and 2708. The 1508 is good for general banana leads and such, and the 2708 works nicely for BNCs and scope probes. Middle Atlantic also make some similar ones that have variable-width slots, and some have little trays for adapters built in as well.
Hanging leads from a slotted rack is great. Did you make that or is there a source for it?
Looks like the OP made that one, but for an off the rack solution, there are the Pomona 1508, 4408, and 2708. The 1508 is good for general banana leads and such, and the 2708 works nicely for BNCs and scope probes. Middle Atlantic also make some similar ones that have variable-width slots, and some have little trays for adapters built in as well.
Probemaster sells a smallish one, but it's only $3.00 so a person could afford a few of them. And I believe they have free (USA) shipping on all orders.
http://probemaster.com/probe-test-lead-storage/
Let's play a game: Find a scope in all this mess, usually to find something in this mess takes 2-6 hours
Looks a lot like a Hantek DSO5000P series model:
Yes it's a Hantek, my DSO5202B is exactly like that.
Hanging leads from a slotted rack is great. Did you make that or is there a source for it?
Looks like the OP made that one, but for an off the rack solution, there are the Pomona 1508, 4408, and 2708. The 1508 is good for general banana leads and such, and the 2708 works nicely for BNCs and scope probes. Middle Atlantic also make some similar ones that have variable-width slots, and some have little trays for adapters built in as well.
Probemaster sells a smallish one, but it's only $3.00 so a person could afford a few of them. And I believe they have free (USA) shipping on all orders.
http://probemaster.com/probe-test-lead-storage/
Those Probemaster test lead holders are nice. They sent me one for free with my last probe order. It's made from a flexible but still rigid enough vinyl/plastic.
Hanging leads from a slotted rack is great. Did you make that or is there a source for it?
Looks like the OP made that one, but for an off the rack solution, there are the Pomona 1508, 4408, and 2708. The 1508 is good for general banana leads and such, and the 2708 works nicely for BNCs and scope probes. Middle Atlantic also make some similar ones that have variable-width slots, and some have little trays for adapters built in as well.
Probemaster sells a smallish one, but it's only $3.00 so a person could afford a few of them. And I believe they have free (USA) shipping on all orders.
http://probemaster.com/probe-test-lead-storage/
Those Probemaster test lead holders are nice. They sent me one for free with my last probe order. It's made from a flexible but still rigid enough vinyl/plastic.
I would prefer this to metal, much less likely to fray or nick the cable insulation.
Hanging leads from a slotted rack is great. Did you make that or is there a source for it?
Looks like the OP made that one, but for an off the rack solution, there are the Pomona 1508, 4408, and 2708. The 1508 is good for general banana leads and such, and the 2708 works nicely for BNCs and scope probes. Middle Atlantic also make some similar ones that have variable-width slots, and some have little trays for adapters built in as well.
Probemaster sells a smallish one, but it's only $3.00 so a person could afford a few of them. And I believe they have free (USA) shipping on all orders.
http://probemaster.com/probe-test-lead-storage/
Those Probemaster test lead holders are nice. They sent me one for free with my last probe order. It's made from a flexible but still rigid enough vinyl/plastic.
I would prefer this to metal, much less likely to fray or nick the cable insulation.
Or you can DIY it as I did on my Instructables.
http://www.instructables.com/id/Turn-Your-Optic-Disc-Tray-Into-a-Cable-Hanger/
Hanging leads from a slotted rack is great. Did you make that or is there a source for it?
Looks like the OP made that one ...
Yep, made from some 5/8" pine leftover from another project. Pretty easy to make if you have access to a table saw. The fingers are glued on and held with a nail. I used spacers to keep the fingers neatly aligned until they dried.
Finally moved
all most of my stuff to the new mancave/corner. Installed some LED strips under the shelves. Hooked up the ESD connectors. And finally gave the fume extractor a try (it works!). Still plenty of things to do, but getting there, slowly
That looks really nice, dvdouden!
I like the white and clear making.
What about the cabinet under the table? Is there still place for your legs or do you pull it out when work is to do?
Cheers
hammy
Thanks!
[...] What about the cabinet under the table? Is there still place for your legs or do you pull it out when work is to do? [...]
No room left at all, but neither is there under the soldering part of the bench. I'm not sure if it will become a problem or not, haven't spent much time at the desk yet. If my back starts to complain then I'll have to find a different spot for the cabinet, but so far it's proven useful: connectors in the top drawer, ICs in the second, passives in the third, unfinished projects in the rest
Haven't posted mine in a while, so here's how it looks at the moment with most of the stuff turned on to emit the appropriate colored lights for the photo.
Haven't posted mine in a while, so here's how it looks at the moment with most of the stuff turned on to emit the appropriate colored lights for the photo.
It's so neat and tidy!
I'm relieved to see you have safety glasses at hand, to protect your eyes from neatness overload.
Here's about as neat as mine ever gets: