Hi,
How to read / write the "DISP" file using DSO-USB-Tool. I proceed as follows:
I select the Read / write File (F4) tab and in the Filename field I entered "/ DISP" then I clik on the "Read from DSO" button. This method does not work.
Thank you.
did you installed the DSO drivers, and if which of them , the original or libusb?
On my computer libusb seems to works better (especially file/read write seems to be affected)
I'm looking for a oscilloscope which is going to be my first and the Tekway DSO1062B looks like a really nice device.
If I were to order a new one today, would I still be able to perform the UART hack? Or did Tekway block it off in a new hard/firmware revision?
If it still is possible I'll be ordering a new one from pinsonne elektronik asap
Hi
As the DSO-USB-Tool has a shell option to send comands to busybox. Is it possible to follow the procedure with that tool, without opening the case and soldering the UART?
For me is not a problem soldering, but this seems easyer.
Thanks
I'm looking for a oscilloscope which is going to be my first and the Tekway DSO1062B looks like a really nice device.
If I were to order a new one today, would I still be able to perform the UART hack? Or did Tekway block it off in a new hard/firmware revision?
If it still is possible I'll be ordering a new one from pinsonne elektronik asap
The answer seems to be yes, as nobody has said the contrary in the last posts.
Hi
As the DSO-USB-Tool has a shell option to send comands to busybox. Is it possible to follow the procedure with that tool, without opening the case and soldering the UART?
sure, move/copy will work, edit (vi) of course not because this is not a real remote shell. So when you need to edit
e.g. the logotype.dis they you can copy to flash drive/edit on PC, or read/write from DSO to PC over read/write function in that
tool or echo new line into file (in case that work).
I'm looking for where I can get a Hantek DSO5102B in the USA. I posted about it here:
LFS / WTB (USA) Hantek DSO5102B oscilloscope new or like newNot trying to intrude but thought I might get a few more responses if I post here, too, since there are so many in this thread that know a lot about this series of scopes. Thanks for humoring me.
Edit: Modified link to show topic title.
check circuit specialists
http://www.circuitspecialists.com/digital-storage-oscilloscopes
Thanks jebcom! Nice to have at least one option besides ebay, and their 30-day return option is nice to know about.
For anyone else, I'm still open to other sources or anyone's used model - please comment on my post in the Buy/Sell/Wanted forum if you have any help.
Now I'll stay out of this thread! Thanks again for letting me intrude.
as few people asked for it, attached BSDL files for:
- Tekway DST1000(A) - SoC S3C2410
- Tekway/Hantek/Voltcraft/Extech B/BM/BMV/S series DSO/MSO/Handhelds, S/N < 15000 - SoC S3C2440
- Tekway/Hantek/Voltcraft/Extech B/BM/BMV/S/P series DSO/MSO/Handhelds, S/N > 15000 - SoC S3C2416
The S3C2416_bsdl file is as well good for Owon SDS users.
Well I just changed my Voltcraft DSO-1062D to a DSO-1202D, and I think it went ok. I can select 4ns/div, so I guess it's ok now
Hmm, I followed this video:
I renamed the dst1062b file to dst1202b, adjusted sys.inf accordingly, and also adjusted tmpdst, logotype and logotype.dis.
Just in case it matters, here is the system information:
Model: DSO1202D
SW version: 2.06.3 (130306.0)
HW version: 10070x555583eb
EDIT: I do get an error that a logo file cannot be found for the 1202 version, but it boots up just fine.
I renamed the dst1062b file to dst1202b, adjusted sys.inf accordingly, and also adjusted tmpdst, logotype and logotype.dis.
actually it is only necessary to rename the /dst1062b to /dst1202b
and (if you need boot logo) edit the /logotype.dis file
Everything else will be automatically changed after two reboots after you remaned the /dstxxxx file
Just in case it matters, here is the system information:
Model: DSO1202D
SW version: 2.06.3 (130306.0)
HW version: 10070x555583eb
is your serial number higher than 15000? (the last numbers)
Btw, there is no such model DSO1202D, so copy paste error or you really typed wrong name?
For the logotype.dis file, it is better to use something generic, like "hantek_DSO5202B", which
will give you then DSO5202B as model.
EDIT: I do get an error that a logo file cannot be found for the 1202 version, but it boots up just fine.
sure, but here somewhere in thread (haha) are all the logos you need (i think),
for the functionality it does not have any influence.
I renamed the dst1062b file to dst1202b, adjusted sys.inf accordingly, and also adjusted tmpdst, logotype and logotype.dis.
actually it is only necessary to rename the /dst1062b to /dst1202b
and (if you need boot logo) edit the /logotype.dis file
Everything else will be automatically changed after two reboots after you remaned the /dstxxxx file
Hmm, ok, that's good to know.
Just in case it matters, here is the system information:
Model: DSO1202D
SW version: 2.06.3 (130306.0)
HW version: 10070x555583eb
is your serial number higher than 15000? (the last numbers)
My serial number is lower than 15000.
Btw, there is no such model DSO1202D, so copy paste error or you really typed wrong name?
For the logotype.dis file, it is better to use something generic, like "hantek_DSO5202B", which
will give you then DSO5202B as model.
Well, my model number is DSO-1062D, so I just changed that to DSO-1202D
I'll change the logotype.dis file to hantek_DSO5202B, so I have a nice startup screen
EDIT: I do get an error that a logo file cannot be found for the 1202 version, but it boots up just fine.
sure, but here somewhere in thread (haha) are all the logos you need (i think),
for the functionality it does not have any influence.
188 pages...
I'll see if I can find them
EDIT: Removed serial number
you should maybe not post the serial here
Ok, havin the latest firmware (whcih is the case for you) you should have 2ns/DIV available if the
hack was successful, so there is something you did wrong.
EDIT: I do get an error that a logo file cannot be found for the 1202 version, but it boots up just fine.
sure, but here somewhere in thread (haha) are all the logos you need (i think), for the functionality it does not have any influence.
188 pages... I'll see if I can find them
I might have seen the post you'd be looking for just earlier today or yesterday. Wasn't able to find it quickly, but maybe this one will help:
https://www.eevblog.com/forum/chat/hantek-tekway-dso-hack-get-200mhz-bw-for-free/msg92830/#msg92830
Sorry, but:
What is the purpose? What I can modify with this BSDL file?
Hi!
Do you have any updated information about DSO5072P
You say: "there is complettly different SoC/new PCB"
Can this model be updated (hacked) with RAM memory?
Do you have any updated information about DSO5072P
You say: "there is complettly different SoC/new PCB"
Can this model be updated (hacked) with RAM memory?
bandwidth can be hacked for sure, what else no idea. All i have are some pictures from top PCB side,
but unfortunately no pictures from bottom side (i know 2ppl haveing P models, but for some reason they
not shot (yet? ever?) pictures from bottom side).
Here what i know so far:
If someone have one of these "P" models, please do a teardwon and shot some more pictures,
especially the bottom side of the PCB is complettly unknown yetupdated, check
https://www.eevblog.com/forum/testgear/hantek-tekway-dso-hack-get-200mhz-bw-for-free/msg264085/#msg264085
Thank you for the help guys! Now I have a 200MHz schizophrenic oscillosope (Hantek logo
).
Forgive my ignorance, but I just wondered... I can now select 2ns/div and 2ns is 500MHz. Does it have something to do with the sampling rate?
I can now select 2ns/div and 2ns is 500MHz. Does it have something to do with the sampling rate?
absolute nothing together
Hi,
Lo
i have a cheap Fluke 124 Scopemeter.
Fluke 124 costs 1700USD, cheap is something else.
Would a Rigol 1052 perform better than this old Fluke Scopemeter?
rtfm
I don't need all the multimeter option of the fluke?
is that a question? we don't know what you might need or not, that's up to you.
and recommendation?
open a new thread ...